Reviews
Fits: HONDA XR250, HONDA XR250 Baja, HONDA XR250MOTARD, HONDA CRF250M, HONDA CRF250L
If you want to slide forward of Chain Slider, it is possible.
I bought this to slide the Chain Slider forward with the rear sprocket change.
The Guide is attached with the front two Bolts and secured to the Bracket with the rear two Bolts.
The Chain Slider will be on the inside of the bracket, so the clearance between the chain and the slider will be compromised. As you can see in the picture, the Chain Slider cannot be installed on the inside of the bracket, but on the outside.
As a Guard, I think it works well for impacts from the outside, but from below it's subtle.
View detail
Fits: KAWASAKI NINJA H2R, KAWASAKI Ninja H2 SX SE, KAWASAKI NINJA H2 SX, KAWASAKI NINJA H2, KAWASAKI NINJA H2R, KAWASAKI Ninja H2 SX SE, KAWASAKI NINJA H2 SX, KAWASAKI NINJA H2
On the heels of Carbonization
The accuracy of Parts is not bad. However, BoltQuantity:Is it natural that it's just a 2pc part? I'm just satisfied with the appearance of this Part. View detail
Fits: KAWASAKI NINJA H2R, KAWASAKI NINJA H2, KAWASAKI Ninja H2 SX SE, KAWASAKI NINJA H2 SX
Slightly difficult to shape and install
At the time of purchase of the Rear Fender of the company, the Image around the Swing Arm
I bought this along with the Swingarm Guard to unify them.
It is made much thicker than other Parts, and it is very chunky.
The strength is considered to be quite high.
It is a shape, but the edge of each side seems to come out in the photograph, but it is a shape that arrives
The outline of Parts is the same as OEM, but there is almost no edge on each side.
It was a rounded shape.
This may be the case with this one, but it is the same as the picture, H2SX!
I thought it was similar to the OEMParts with the Edge effect of the
I was quite disappointed.
In addition, when it installs, OEM is made along the Swing Arm shape, and there is a sense of discomfort.
It is not, but this seems to be attached distortedly because of the shape that the part is a little off.
It looks like
If you look at the parallelism between the Chain and the Body, you will see that they are parallel.
It doesn't seem to be wrong.
I can understand a little gap if it is a large size part, but for a part of this size.
I felt that the details were a little sweet.
Installation is the most difficult of the three Parts I purchased this time.
The addition itself is just a matter of widening the hole a bit to allow the OEM collar to pass through.
If you don't find the right direction to spread the bolt, it will be difficult to tighten the bolt.
There are two Bolt locations, one on the side and one on the bottom.
First I removed the OEM, then I aligned it and tried to find a direction to widen the hole.
It is better to
If the Bolt is misaligned as described above, it will be difficult to tighten.
However, if the collar is made into a long hole, it will not fit in the hole.
It is thought that it does not stop tightly.
Once the hole expansion is complete, run the OEM Color through the RubberWasher that comes with the
Insert the bolt from the reverse side into the hole of this part, as opposed to the OEMParts installation.
Stop.
There is one point to note when removing the OEMParts and installing thisParts.
The Bolt here is quite hard because of the powerful screw lock agent.
Also, the lower Bolt stops at a slight angle from front to back.
Therefore, it is necessary to make sure that the direction of the screw and the position of the hex do not deviate when removing and installing.
Make sure the bolt direction is straight and push it in firmly to turn.
The Bolt has a slightly low head, so the Hex is shallow, and if you're not good, the Bolt's
It will lick the hexagonal part.
View detail
Fits: MV AGUSTA F4 1000S, MV AGUSTA F4-750, MV AGUSTA F4-BRUTALE, MV AGUSTA F4 1000AGO, MV AGUSTA F4 TAMBURINI , MV AGUSTA F4 BRUTALE910S , MV AGUSTA F4 BRUTALE 910R , MV AGUSTA F4 1000R, MV AGUSTA F4 1000S SPR, MV AGUSTA F4 SerieORO , MV AGUSTA F4 RR1078, MV AGUSTA F4 1000R312, MV AGUSTA F4S, MV AGUSTA F4SPR, MV AGUSTA F4R, MV AGUSTA F4 SENNA
1078
It was just like the image. I am satisfied with it. View detail
Fits: MV AGUSTA F4 1000S, MV AGUSTA F4-750, MV AGUSTA F4-BRUTALE, MV AGUSTA F4 1000AGO, MV AGUSTA F4 TAMBURINI , MV AGUSTA F4 BRUTALE910S , MV AGUSTA F4 BRUTALE 910R , MV AGUSTA F4 1000R, MV AGUSTA F4 1000S SPR, MV AGUSTA F4 SerieORO , MV AGUSTA F4 RR1078, MV AGUSTA F4 1000R312, MV AGUSTA F4S, MV AGUSTA F4SPR, MV AGUSTA F4R, MV AGUSTA F4 SENNA
1078
It took a long time to get it delivered, but I was able to install it almost Bolt On and I am satisfied with the quality. I am very happy with the quality. View detail
Refreshing to look at.
The performance does not change, but the appearance is refreshing. View detail
Replaced for DAYTONAAdjustable rear shock installation.
Replaced OEM to install DAYTONAAdjustable rear shock. I'm very happy with it and it's more stylish than OEM. It would have been better if the paint was Plating… View detail
no problem
Bolt On is a must have for circuit driving. View detail
Installed for regulation support
It's one of the few tzmAftermarket parts. I was able to install it securely without any sticking. View detail
I knew you'd want a dedicated one!
[How is it used?
It is used for YZF-R25 that has been converted to Racer.
Stand Hook to be tightened together is MORIWAKIEngineerRing's Stand hook roller.
Part Number:05210-10350-00
Was the one you received as per Image?
It was just like the image!
Was the installation difficult?
Nothing too difficult, just take the Bolt off and put it on!
How was your experience with it?
It's good to have a dedicated product. I used to use the one of A-TECH (This was also a dedicated product...) I was using the one of
At the time of the race car inspection, the person who inspected the car told me that this (A-TECH) was too far back and it was useless. So I bought this product to replace it.
This product is firmly offset to the front side, and it plays a role as a chain guard firmly.
The guard part is also solidly built, and the material is thick plastic, so I don't think it will be damaged or broken.
[Included Parts:were they on?
There was not. It is the content of the photograph of the product Page.
[Was there anything that disappointed you?
Not really!
View detail
Fits: YAMAHA YZ 450F, YAMAHA YZ 250F, YAMAHA WR 450F
Repair Parts is also available.
The structure is simple, and I think there is no large difference in function and life compared with the thing of ZETA. (ZETA products are also being used in other cars)
The WearPad's arrival was erratic, and the ZETA was no different.
It is good if you check it frequently, but it takes time to procure in Troubleetc. (More than a few weeks) In some cases, it is recommended to purchase Repair Parts as well.
WearPad is a common part for other models, so I think it can be used for other models.
View detail
It's a different model of car, but it's not impossible to use.
[How is it used?
I used it on my YZF-R25 that I use in Race because it is required to be installed in Race regulation.
Since the delivery date for the R25 was long, I chose this one that was in stock.
Was the one you received as per Image?
I'm very happy with it.
Was the installation difficult?
It is very easy to co-tighten with Bolt.
I could have co-tightened the Stand Hook Bolt, but it would have been too far back on the R25 to make sense.
As you can see in the picture, it's lame, but I used Universal Bracket to bring it to the front side.
How was your experience with it?
It does the bare minimum of what I need it to do. Unfortunately, I'll be going to Spare when I receive one for my R25.
The upper side should be secured with Swing Arm and Double-sided Tape.
[Included Parts:were they on?
Comes with a 6Bolt
[Was there anything that disappointed you?
Not particularly
I don't really recommend it, because it's not a Manufacturer-inspired installation.
I think it can be used for any kind of car depending on your ingenuity.
The accuracy of the product was not bad. It was thick enough and chunky enough.
You can use it with confidence in terms of strength, and Bolt can be tightened firmly.
View detail
Fits: KAWASAKI NINJA H2R, KAWASAKI Ninja H2 SX SE, KAWASAKI NINJA H2 SX, KAWASAKI NINJA H2, KAWASAKI NINJA H2R, KAWASAKI Ninja H2 SX SE, KAWASAKI NINJA H2 SX, KAWASAKI NINJA H2
It's a small part, but it stands out!
I have an Inner fender made by Speedra, and I bought their Drive chain guide.
Spec. is the same as Fender, twill weave with gloss. The look is definitely better than OEM plastic parts.
In my case, I was able to replace it with Bolt On without having to modify the hole processing at all. However, the quantity:2pc. If you have a HexaWrench for Ratchet, it is easy.
It is a small part, but it is unexpectedly conspicuous, and I think that it is a reasonable price if it is thought that it is made of Dry carbon.
View detail
Fits: YAMAHA YZ 450F, YAMAHA YZ 250F, YAMAHA WR 450F
I'm not sure it's functional.
Protection is no problem. 。 It's a two-piece structure, and I like it because it's simpler than other manufacturers' products.
There is no damage that becomes impossible to run even if it hits, and I think that it is difficult to give stress to the attachment part of the Swing Arm.
However, the decrease is early! I think that it is too early even if Repair Parts comes out however.
It is a pity that it seems to take longer than expected when it is also out of stock.
View detail
Chain Guard
Parenthesis I hope you are feeling better 。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。 View detail
Carbonization with TSR products for peace of mind
If you're promoting carbonization, this one's for you!
It's an inconspicuous place, but it's highly self-satisfying.
I compared it with OEM Product, but I chose this one for its design and material.
(OEM is better in cost and firmness.)
I'm sure there are actual safety considerations, but I have no way of experiencing (or wanting to) that effect, so I don't know.
but I trust the product because it is produced by TSR.
In the introduction Page of the product, it is fastened with the screw of the attachment, but I use it with Stand Hook.
I didn't have any problems with tightness.
The delivery time was 2 months, so I waited patiently, but in my case, it took less than a month.
View detail
Fits: KAWASAKI NINJA H2R, KAWASAKI Ninja H2 SX SE, KAWASAKI NINJA H2 SX, KAWASAKI NINJA H2, KAWASAKI NINJA H2R, KAWASAKI Ninja H2 SX SE, KAWASAKI NINJA H2 SX, KAWASAKI NINJA H2
Satisfied?
Material:Carbon product, clean and good installation.
It's just expensive...
But I'm satisfied.
View detail
Fits: KAWASAKI NINJA H2R, KAWASAKI Ninja H2 SX SE, KAWASAKI NINJA H2 SX, KAWASAKI NINJA H2, KAWASAKI NINJA H2R, KAWASAKI Ninja H2 SX SE, KAWASAKI NINJA H2 SX, KAWASAKI NINJA H2
Installation is Large
The holes are not in the right position or thickness.
Anyway, the adjustment is Large strange.
The included RubberWasher makes no sense.
It is written in the Construction Manual that the holes may need to be adjusted, but it is not that Level.
View detail
Fits: KAWASAKI ZZR1100, KAWASAKI GPZ900R
Can't you just half install it?
I'm looking forward to installing it on my zzr1100, and I'm surprised!
I can't reach the front attachment point.
The back part only sticks here …
For zzr1100 and zzr1100 Swing Arm cars... wasn't my zzr a zzr? (Laughs)
There seems to be a difference depending on the year, but they don't seem to grasp that since it even comes with an installation screw.
But I was willing to pay the price to buy a curved aluminum plate at this price if I wanted to imitate it
It's a shame you can't get it right.
I wish you could respond to this in some way.
If you're just sorry for the text, well, that's just the way things are.
I think that's about it.
For now, we will produce the installation part with the aluminum plate.
View detail
For Regulation.
It is installed for race regulation.
There are various types of Chain Guard, but the only type of Machine I have is the one that is co-tightened to the Rear Stand Receptacle, or the one that mounts to the Swing Arm by drilling a hole.
To be honest, I don't feel comfortable with the Swing Arm type that makes a hole in the Swing Arm, so I bought this one. To be honest, I don't feel comfortable with the Swing Arm type, so I bought this one.
By co-tightening, the position of the STAND receiver can be changed to QUANTITY:Pair (for Left and Right) You can use a spacer, such as Washer, for the other one. Balance is better.
View detail