Reviews
StylishUP more bad
[How is it used?
Optimized for waiting ride in Touring
Was the one you received as per Image?
Large satisfactory, good looking
Was the installation difficult?
Anyone can install it easily.
How was your experience with it?
Satisfied with good rear visibility.
[Included Parts:were they on?
no problem
[Was there anything that disappointed you?
None
Point and hang of installation
Increased tightening after installation
Availability and comprehensibility of Instruction Manual/Points to note/Items to be purchased together/Opinions and requests to the Manufacturer
View detail
Satisfied.
I am a SR400FI user. I purchased the above product to replace it with the SR500 genuine up handlebar while using it as a Hurricane handleset. It is installed without problems because it is +10cm higher than the genuine product. Will be purchasing more for the future. -------------------------------------------------- -------- SR400FI user. Previously, I purchased the above product to replace it with SR500 Genuine Handlebar while using it as a hurricane handleset. It is +10cm than genuine products, so it is installed without any problem. We will buy additional for later. Powered by Google Translator View detail
Praise!
It leans forward a little, but not so much that it's tight, and the Corner is not too bad. I think the Large is strong enough for long distance touring. View detail
Fits: KAWASAKI BALIUS2, KAWASAKI BALIUS, KAWASAKI ESTRELLARS, KAWASAKI ESTRELLA
Not as good as OEMs
Even though I tightened it on the meter gear side, there was a small gap, so I installed it with an O-ring over it to prevent water from getting in.
I think OEM is the best choice for Speedometer unless you are concerned about Mesh.
View detail
Fits: HONDA glom, HONDA glom
Posture changes
Product Name
HURRICANE HURRICANE Forward Conti2 type Φ7/8 inches Handlebar
Item Number
HB0038B-10
Vehicles
Grom ( JC61 ) 2015
Number of man-hours
About 1 hour
Required Tools
Torque wrench, hexagon socket, Hexagon socket, Extension bar, Combination wrench, -Driver, Hammer, Pliers, etc. would be perfect.
Why did you choose this product?
When we installed Grom's Rear Sets, we thought it would be better to change the handlebar as well, so we chose this one. I also found many people on the Net who had chosen this handlebar for their Groms, so I decided to purchase it.
Was the one you received as per Image?
It was as shown in the Image, only with Handlebar.
Was the installation difficult?
I think it is easy because the mounting holes are already drilled. However, if you don't organize and move the Cable system, it doesn't fit very well. It took me a long time to fix that part.
How was your experience with it?
The posture has been changed to an aggressive posture. By changing the position of the hips, you can go from a forward leaning posture to a comfortable upright position.
[Was there anything that disappointed you?
Nothing in particular. I would be happy if it were cheaper.
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
View detail
HURRICANESlot cable
I purchased this one because OEM Parts has been discontinued.
Brand strength and no quality issues at all.
Replacement requires time since the carburetor needs to be removed and installed.
View detail
Fits: YAMAHA MT-09, YAMAHA XSR700, YAMAHA XSR900
XSR900
Great handlebar for xsr900. Install was great and easy. Took about an hour to do. Cheap and very fast shipping. Highly recommend View detail
It's adjustable, so that's helpful.
Because NORMAL is not adjustable
It's exhausting.
I'm not sure about the NORMAL thin Size.
Select this item.
Both aperture & droop can be adjusted to bring the Position closer to the ideal.
Not much to see, but the design texture could use a little more.
Just speaking of HURRICANE, this is the Design. w
In the past, there used to be a Quick Release separate handle, but I don't see it anymore.
The replacement of separate handles requires a certain amount of knowledge and tools, etc.
As a precaution, it is better not to Cut the length
Since it is Limit in Clutch's Switch, etc.
As for working Access... well, there are many ways to do it.
View detail
Before Separate handle
Purchased to reverse mount on SR400.
When changing the position from NORMAL to a separate handle, I thought about using a separate handle, but then I took a breath. This product was the best for making use of the NORMAL Throttle Wire, Clutch Cable, etc. to tilt the car forward. There was no problem with the position, but I was not satisfied with the appearance, so I ended up using a separate handle. Positioning is different from the Separate handle, which is clipped on to the Handlebar above the Top Bridge, so it is necessary to check the interference between the Switch box and the Tank.
View detail
While you are shopping
It is just a decoration, if you like.
There is no sense of discomfort as if it had been attached from the beginning.
It is completely self-satisfying because no one but the person himself notices it.
View detail
Fits: KAWASAKI ER-6n, KAWASAKI NINJA400 (2014-), KAWASAKI Ninja 650
Fender Eliminator Kit
It arrived earlier than I expected, which was a big help. The instruction manual for installation is difficult to read … I thought it would be better to make it a little larger. I am very happy with the quality of the product and the price. View detail
Black Pill Installation
About Pin for Switch box 。 On the Left (Blinker) side, it is enough to measure the distance of the hole from the end of the STD Handlebar, but on the Right (Kill switch) side, the switch box is Large, so if you take the distance from the end, you will not get Mirror. 。 Rearview mirror stay was temporarily fixed and the pin position of the switch box was reflected from there. 。 We wanted to minimize the overhang as much as possible.
The inner wall of the BackMirror Clamp was filleted to avoid the SWCondor welds.
Drilling a pin hole can be done within 5 minutes without special tools if you turn the drill slowly after punching a pin.
I can open it. 。 When drilling, the side to be drilled was placed on top and the CenterPost was tightened.
Since the handlebar grip was still new, a long Phillips screwdriver was inserted through the gap to create a gap, and parts cleaner was sprayed on it to remove and reuse it.
After installation, it is clearly comfortable in terms of Position.
View detail
Size is different
I ordered an M6 and received an M5 even though the bag said M6.
I couldn't wait to replace it, so I drilled the holes myself with a Drill and re-cut the screws with an M6Tap and installed them.
View detail
Throttle Cable
I bought it because of its Brand power.
Some compromises have to be made because OEM Product has been discontinued.
View detail
For Z125 Pro
The Rear Sets and STD Handlebar were not in the right position.
I bought this Handlebar around April 2022, but the color I wanted:Black's delivery time, at that time, was more than six months,
We had no choice but to use a color with a fast delivery date.:Chrome plating was used, and the Fork cap and Stem Nut were replaced,
I think the appearance of the PlatingHandlebar is no longer incongruous.
(Photo 5) Plating color plastic cap of (Photo 4) The first one is attached to the position of the second one, but one of them came off at some point,
Posh Bar End (031072-11-10, color) with the same Handlebar diameter:Titanium) was mounted in that position.
Handlebar color:Also for Black (Photo 5) It has a Plating color Cap of (Photo 5) Cap of the
If you want to change the Handlebar to the same color or Colorful, I think you can pull out the Cap and change to this kind of Bar End.
When installing the handlebar, I used a Made by HURRICANE 25mm Handlebar Up Spacer that I originally had.
As a result, when the Handlebar is cut off at the end with the foot in the Knee grip position, Tank,
The Bar End did not hit the foot, and a Clearance of about 2 cm was created.
The passenger's posture is tilted forward. On the other hand, the arms are extended, so the upper body is no longer cramped.
I have used it for 1 year and 2 months and I am satisfied with it!
View detail
Fits: HONDA CB1100, HONDA CB1000 SF (Big One), HONDA CB-1, HONDA CB-1, HONDA HORNET600, HONDA HORNET250, HONDA ZOOMERX, HONDA JADE, HONDA glom, HONDA glom, HONDA X4, HONDA X4, HONDA X11, HONDA VTR250, HONDA VTR1000FVTR1000F FIRESTORM, HONDA VTR TypeLD, HONDA VFR800, HONDA NSR250R, HONDA NSR250R, HONDA NSR250R
For Z125 Pro
I took the opportunity of replacing the Z125 Pro Handlebar and incidentally replaced the Stem Nut.
For the price, I think it has a dress-up effect, and the appearance is Refreshing.
I think it matches with DAYTONA and Front fork cap.
When tightening the Nut, it is best to take care not to damage the Nut itself.
Also, if the tightening Torque is met, there is no concern that it will loosen.
It has been about 1 year and 2 months since installation and I am satisfied with no problems.
View detail
Fits: HONDA NC700S, HONDA GL1500GOLD WING, HONDA GB250 CLUBMAN, HONDA CBR600RR, HONDA CBR600F, HONDA CBR1100XX SUPERBLACKBIRD, HONDA CB750, HONDA CB400SUPER BOLDOR, HONDA CB400SUPER BOLDOR, HONDA CB400SUPER BOLDOR, HONDA CB400SF, HONDA CB400SF, HONDA CB400SF, HONDA CB1300 SF, HONDA CB1100 RS, HONDA CB1100 EX, HONDA CB1100, HONDA CB1000 SF (Big One), HONDA CB-1, HONDA HORNET600
Looks Upgrading:??
The NORMAL feeling is not bad, but this one is more Upgrading??Cost is not bad either! View detail
z900rs only
When choosing a handlebar for the z900rs, I compared six HURRICANE handlebars in person and decided on the Conti2 model.
I am very grateful that HURRICANE has so many varieties to choose from, and I can choose according to my taste.
The mounting holes were also neat.
I have long arms, but it is much easier to ride from the OEMHandlebar. I wish I had changed it sooner~.
View detail
Fits: KAWASAKI BALIUS2, KAWASAKI BALIUS, KAWASAKI ESTRELLARS, KAWASAKI ESTRELLA
If the length is suitable, it can be used for other vehicles!
It was 40mm longer than ESTRELLAOEM, so we diverted it to another Kawasaki vehicle.
Cable ringing was minimal and the mesh texture was good.
The mounting part is only lightly tightened with pliers.
If it is weak, it will come off while driving and the Cable inside will fall. (Experienced)
If it is strong, it will be damaged because the mounting part is thin.
View detail
CondorSW
With the OEMHandlebar, my arms were open and I was leaning forward halfway, and after an hour my arms were numb and my back was a little sore, but this has improved!
The position of the brake lever is a little delicate, but I think it can be handled by Lever.
I am installing it without Spacer.
View detail