Reviews
Very precisely made
Beautiful shaft, extremely well made, the fit is very precise and it gives a very secure feeling when torqued up, It greatly adds to the appearance of my machine, I'm very happy with it and I feel it offers good value, I also have the JB Power front wheel shaft and the JB Power swingarm pivot shaft, View detail
Tail Bulb replacement for KSR's Fender Eliminator Kit
I purchased a used KSR80, but the previous owner installed a Fender Eliminator Kit, and the tail lamp is a Lucas type.
There was a Trouble with Tail Bulb immediately after purchase.
I removed the Lens to see the model of the Lamp to replace it, but unlike the usual Double Bulb, the head was a Small Rhinoceros Bulb.
This Type was not sold at Home center or Car Shop 。 Maybe MotorcycleParts specialty stores have them, but I can't find any near me. 。
However, because the length of the Tail Bulb was different, it interfered with the Lens, causing the Lens to chip, melt, and consume more power due to its higher wattage.
I had put it off because it was inexpensive but the shipping and other things made it needlessly expensive, but I had some shopping to do at WeBig, so I bought it as a package deal.
After installation, there was no interference (obviously), and since the Watt number was lowered, the power consumption was also lowered, eliminating the concern factor.
I am planning to eventually switch to LEDs, but there is a barrier of full-wave rectification, so I may end up putting it off.
View detail
It gets pretty hot.
As expected of a genuine product. The grip is comfortable. The temperature rises to the point of being hot when set to high. I survived one winter with winter gloves and this grip heater. In the middle of winter, there may be nothing better than electric heated gloves (I have never used them, so I can't say for sure...), but the best thing is that it is easy to use without the hassle of connecting an electric cord to the glove when using it, and it extends the use season of Pairslove leather gloves, which I use most during the touring season. The biggest advantage is that I can extend the use season of Pairslove leather gloves, which have been my most favorite during the touring season. After all, it is nice to be able to use familiar gloves that winter gloves and electric gloves do not have. There are cheaper external products available, but if you want to use them for a long time, genuine products have a different sense of security. We highly recommend them. View detail
![Aluminum Billet Handlebar End [GrooveType]](https://img.webike-cdn.net/catalogue/images/127179/BEGV_TS.jpg)
Fits: SUZUKI DL1000 V-STROM250SX
Car-specific installation kit?
As a result of the installation, there is a 7mm gap (see photo) at the Knuckle guard mounting point, and it rattles when driving.
This is happening because the thickness of the Color Guide for the car-specific installation kit is 12mm and Large!
In the end, to eliminate the 7mm gap, we purchased a K-CON M6 18Φ 5mm thick aluminum spacer and installed it to eliminate the gap.
In addition, the DL1000 V-STROMSX bar end attachment part is described in the instruction manual as a type that compresses the rubber between the bolt and the handlebar and crimps it to the handlebar, even though it is a type with a screw cut on the end of the handlebar (the parts list does not show such a construction). (Even the Parts List does not show such a structure.)
Thinking that perhaps a mounting kit for another model was mistakenly included, I inquired at the ManufacturerSite, but received no response (I was disappointed because I had been using the Manufacturer's Lever until now).
The quality and texture of the product are highly evaluated, but the mounting kit is not good enough.
Dear Webike.
Not because it was a SPECIAL PRICE.
View detail
for Race, it seems.
I didn't like how thin the swing arm of the NS-1 was back then, so now that I'm a large person, I decided to secretly buy one without telling my wife and secretly install it.
The design looks good, the Installation Instruction Manual is missing and I know that I have to buy it.
"For Race" and the enclosed handwritten paper stated (^_^;)
I thought it was very important information that I wanted to know before I bought the car. I am a little worried.
View detail
Fits: YAMAHA YZ125, YAMAHA WR125, YAMAHA TY250 Z SCOTISH, YAMAHA DT200 WR
Quickly to run
With the Front12T, you will be running Quickly, both on forest roads and in town.
It is affordable and I feel the effect of the replacement.
View detail
I miss the colors and design.
Good old-fashioned color and design. View detail
![Seat Cover [SK-110V]](https://img.webike-cdn.net/catalogue/images/13570/32632935_TS.jpg)
Fits: KAWASAKI Estrella RS, KAWASAKI Estrella RS Custom
Stretched well.
I bought Tucker to reupholster my old motorbike, and I didn't have the budget to spend tens of thousands of dollars on OEM or custom-made stuff, so I decided to do it myself at a low price. The thickness and texture of the seat is not as good as OEM, but I regretted that it looked cheap when I received it, but after I stretched it, it looks beautiful. The ride quality is also better. Even if I applied anti-slip coating, after applying the brake, it was gapping in front of the car but now it is stable and easy to drive without sliding. The material that looked cheap is now shiny and beautiful. I've never done any DIY before, so I'm a beginner and I'm too lazy to watch YouTube, but I can get by even if I do it haphazardly. Now I'm planning to reupholster it again and put Nylon in it for rain protection and Gel Zab under the Seat for long distance protection. View detail
Fits: KAWASAKI ER-5, KAWASAKI GPX600R, KAWASAKI KLE500, KAWASAKI KLF220, KAWASAKI Eliminator 600, MAGNI 1000 Australia2, MOTOGUZZI 1000 Ditna RS, bimota YB-4, bimota YB-6, bimota Dietsch 1000, bimota Flannel 1000, HONDA CB1100F, HONDA CB1100R, KAWASAKI 1000GTR, KAWASAKI 250TR, KAWASAKI EN400, KAWASAKI EN500, KAWASAKI EX-4, KAWASAKI FX400R, KAWASAKI GPZ1000RX
Idling stabilized?
I changed the oil as part of maintenance, and it seems to have stabilized the idling, but I don't feel that the power is increased. I really don't know if the period to change the oil was too short and the oil was not so deteriorated, but it is an old motorcycle and I will replace the oil as soon as possible. Next time I will buy a Torque wrench and tighten it with the specified Torque. View detail
Fits: HONDA CB1100, HONDA CB1100 RS, HONDA CB1300SB, HONDA CB1300SF, HONDA CB1300SUPER FOUR SP, HONDA CB1300SUPER BOLD'OR SP
General Slider
The car was delivered with DAYTONA's Engine Guard installed.
Because I scraped it just by driving normally on a mountain road,
Changed to Slider.
I am concerned about Damage to the Motorcycle in the event of a fall.
View detail
Fits: YAMAHA MT-25, YAMAHA YZF-R3, YAMAHA MT-03, YAMAHA YZF-R25
It looks better now.
Model YZF-R25
The Rear is quite dirty and it is now clean. the Brake Caliper is OEM and the Pad is DAYTONA, but I am glad I replaced it. The braking power is normally increased and I am satisfied.
View detail
Easy to install!
Installation was easy.
Japanese Vehicle Inspection Correspondence, but I think the sound is too loud.
But it's cool, so I'm satisfied.
View detail
Large satisfied
Installed in CHALY.
It needed a little modification for the CUB, but it is quite good for a little flippant shopping.
View detail
Fits: KAWASAKI Ninja1000, KAWASAKI Z900, KAWASAKI Z800, KAWASAKI Ninja1000SX, KAWASAKI Ninja ZX-6R, KAWASAKI Ninja650, KAWASAKI Ninja400, KAWASAKI Ninja250, KAWASAKI Ninja ZX-25R
It's easy.
Seal for easy installation!
The light blue reflection alone has a custom feel!
I loved it.
View detail
Fits: DUCATI SCRAMBLER DS FASTHOUSE, DUCATI SUPERSPORT 620, DUCATI MULTISTRADA 1200 PIKES PEAK, DUCATI MULTISTRADA 1200 S, DUCATI ST3, DUCATI SPORT 1000 S, DUCATI MONSTER 795, DUCATI DIAVEL 1200, DUCATI SCRAMBLER NIGHTSHIFT, DUCATI SCRAMBLER MACH 2.0, DUCATI SCRAMBLER CAFE RACER, DUCATI SCRAMBLER DESERT SLED, DUCATI SCRAMBLER ITALIA INDEPENDENT, DUCATI SCRAMBLER FLAT TRACK PRO, DUCATI SCRAMBLER URBAN ENDURO, DUCATI SCRAMBLER STREET CLASSIC, DUCATI SCRAMBLER CLASSIC, DUCATI SCRAMBLER FULL THROTTLE, DUCATI SCRAMBLER ICON, DUCATI SUPERSPORT 750
The maintenance improvement after installation and the visual design is great, but …...
It's no surprise that Doka's dry Clutch is a natural choice for OpeningCover.
Wet Clutch cover. [Color] When set to Clear, the Impact of the visual design is the best!
However, when the difference in temperature is extreme, condensation and emulsification on the Glass surface is very severe. When the difference in temperature is extreme, condensation and emulsification on the glass surface is very severe.
It's dirty and you can't see what's inside, so it's kind of a bad parenthesis (laughs).
However, switching to this Cover will super reduce the hassle when changing clutches!
Since only the clear part is removed from the O-ring, there is no need to peel & attach the liquid gasket.
OIL is also hardly reduced, so that's great to think about!
I think the price is about the same considering the design and quality of workmanship.
What others think of this price for this part is...
View detail
![[Repair Parts] Lock Set [Z641NM]](https://img.webike-cdn.net/catalogue/11160/66524_image_TS.jpg)
Fits: Others E470, Others E370, Others E340
GIVI is still good
Motorcycle top cases are all the same, right? You may think, "What's the difference between a motorcycle top case and a top case?
However, the difference is that GIVI has a good lineup of repair parts.
I believe Top case does not need a key.
It is troublesome that both GIVI and other Manufacturers have a mechanism that prevents the lock from coming off unless it is locked.
GIVI, in fact, can be unlocked with a little modification,
However, this process will result in a demerit that will make it impossible to lock the door,
In the first place, I think it is strange to put something that is not good to be stolen in Motorcycle's Top case.
When you remove the key, you will see red plastic on the reverse side, so you just need to cut the part that is caught by the key.
At any rate, the Impression this time was that GIVI is a good company with a solid lineup of Repair Parts.
View detail
Fits: Others Wire clutchCompetition model, SUZUKI RMX450, SUZUKI RM-Z, SUZUKI RM, KAWASAKI KLX450R, KAWASAKI KX-F, KAWASAKI KX, YAMAHA WR-F, YAMAHA YZ-F, YAMAHA YZ, HONDA CRF-X, HONDA CRF, HONDA CR
Definitely lighter.
I had been using OEM Clutch for a long time, but it was too heavy and tiring, so I replaced it with this one.
To install, remove all the originally attached clutch lever and holder, leaving only the wires in place, and then install.
The dust cover is screwed on, so it must be disassembled and assembled before installation.
Also, the Clamp portion is rotated so that it is less likely to break than a regular Lever or OEM.
The Nut that adjusts the distance of the Lever is also hexagonal, a spec. that can be firmly fixed in place.
I prefer to set it quite far away, but it feels quite light when I pull the lever, I don't know if it's because of the Ratio or some other secret, but I think you can feel it the moment you hold it.
View detail
Easy to install, but ???.
Installation is easy, and the design fits well with the car body without any discomfort. However, I think that the reflector should be included from the beginning since ACTIVE also manufactures a reflector. View detail
YOSHIMURA Fender Eliminator Kit
Item arrived..super fast shipping.3 days arrived.check and all item is in order.never been disappointing.highly recommend.thank you team webike.awsome job.5 ⭐ View detail
SM LINEFender MD44 installed
As per the impressions of our predecessors, the MD38/44 can be installed without any body modification.
Reasonable price and VisualUp, no complaints!
However, in my case, I have prepared the following additional components
Spacer:6.2mm ID x 15mm OD x 6mm L (qty:4)
Bolt:M6 x 30 (qty:2)
Flat Washer:M6 x 22 (qty:4)
When MD38/44 is installed, the spacer thickness should be at least 6mm to avoid interference with the car body. The outer shape may be a little larger than 15mm.
It is fastened with 4 OEMBolt, but for some reason, Quantity:I also bought Bolt because each 2pc is a different length (my used one) and when I put Space on, the shorter one doesn't reach.
When tightening from the tire side, the bolt groove on the FenderBody is large, so the washer is also large. 22mm larger than the bolt groove will cause the washer to ride up.
For your information.
View detail