Reviews
scratch-resistant
It was put up to prevent Tank from being scratched. View detail
Easier Knee grip
This will be a reReview.
Immediately after delivery, only the side cover was attached, but later the tank side was also attached because the legs hit the tank side when the vehicle body is supported by the outer legs with the ass shifted, such as when driving on a mountain pass.
The positioning was done without any particular instruction manual, and the position of the legs was determined by straddling the tank, making sure not to miss the point where the legs hit the tank, and fine-tuning the position so that the line of the tank would be consistent with the line of the tank.
As with the Side cover section, when attaching, peel off the backing paper gradually to prevent air bubbles from entering, and apply it from the center outward in a way that releases air.
Although I am rather clumsy, I think I was able to apply it reasonably neatly.
As a result of driving on the pass, the Tank was well supported during Cornering and had the expected effect.
Especially in the forward leaning posture of SS, it is somewhat easier to support the upper body by having a good knee grip.
As I wrote in my last Review, [Color] Even though it is called Clear, I am a little dissatisfied with the Cream coloring.
A little more transparency would be nice without destroying the design of the car body.
View detail
It is a good item
[How is it used? It's been a month since I installed it on the Meter panel of my NINJAH2SXSE (2021 model).
Was the one you received as per Image? The size is perfect for the Meter screen. I was worried about damage to the screen since the Meter is an LCD panel, but I am now feeling more secure.
Was the installation difficult? It's easy. It is the same way as the film on a cell phone screen. A small amount of detergent was enclosed in the bottle to wet the adhesive surface during installation. I did not see any Instruction Manual. I diluted it and used it. I sprayed it on the adhesive surface and pushed out the water with the included spatula, which I rubbed lightly to avoid scratching the surface of the film. Moisture was absorbed with Tissue.
How was your experience with it? I have been using it for a month now and I have no problems. There are a few small bubbles left, but no problem in use.
[Accessories] A bottle containing a small amount of detergent and a spatula are included.
[Was there anything that disappointed you? Nothing in particular. It is just a Film, so the cosmetics are rather expensive (2 stars). The shape is perfect and even an amateur could apply it well, so I am satisfied (4 stars overall).
View detail
There is also some gripe feeling.
Recently, SmallWound has become prominent on Tank!
I told myself not to worry about it because it was a training machine and I used it heavily, but I found an outlet product and stuck it on for prevention& protection.
The result was a Large success. The cut was quite precise, and by carefully removing air bubbles while adjusting the cut, I was able to achieve a generally clean finish.
Although it is not a GripType, it seems to have a non-slip effect and has some grippy feeling.
The work is to clean the surface thoroughly with Seat for removing oil from the attached kit, and then apply a liquid detergent diluted in the same way as for WindowFilm. (Container is also included.) Spray generously on the paste surface and Film and adjust the position.
The included spatula for pasting is just the right size and easy to use, but it seems to have two sides, so if you make a mistake, a wound will remain as shown in the image. (It is hard to see due to the reflection.)
Because of the complex shape of Z, we divided it into parts and removed air bubbles from the center outward.
To be sure, I left it for a day after the water dried to check the adhesion and took it for a test drive. There were no parts that were about to peel off, and the adhesion was firm, so there was probably no need to worry.
If it can be applied neatly, it will look good, and even slippery materials such as synthetic fibers can be used to hold the tank in place. (Not compared to GripType...)
The instruction manual is not included in the package, so please check the manual before preparation, and be prepared to work carefully and sparingly.
View detail
I love it!
I am satisfied with the outstanding Hold performance and the Large change! View detail
Fit for purpose
I chose the clear film despite being put on a black tank. The manufacturer claims the pads will take on a slight blue colour against black background.. but it's not really noticeable for me. It did take a bit of effort to push the majority of air bubbles out during installation. The colour block on the tank is still nicely visible, so that's a bonus. Make sure you know where your knees tend to sit & move on the tank before fitting the pads & allow this to guide your fitting location on the tank. View detail
The price is reasonable and the effect is decent.
Each car is Exclusive Design, or the price is high.
However, considering the difficulty of installation and the effect after installation, it was a good purchase.
I think I did.
I have read in other reviews that the adhesion is weak.
If it is done, it will adhere properly to the tank and resin parts and is strong enough.
After installation, I drove the car and it was very easy to get a good grip on the knee.
Ride quality and operability have improved.
View detail
Fits: HUSQVARNA Svartpilen 125, HUSQVARNA Svartpilen 200, HUSQVARNA Svartpilen 250
PetitCustom
I didn't want to put Wound on the Mud black part and I was worried about wearing Knee grip. But I bought it because I found it more tiring to drive for more than 30 minutes with the Knee Grip.
I haven't run the car yet, but it was easy to install without losing much of the design. It was a bit confusing to find the right direction to put it on, but as expected from Exclusive Design, it fit perfectly here! I was a bit confused about the direction to put it on, but as expected of Exclusive Design, it fit perfectly in the right place! Now I can use the knee grips without hesitation.
View detail
Knee grip
I didn't have a setting on my Stomp Grip, so I was looking for something else and found it cheap, so I bought it. View detail
Eazi-Grip Meter Protection Film for Z650RS
The MeterFilm from another company was made of a thin underlay-like material, and there were many places where air could not escape, but this product is a flexible material, and air escaped immediately using the included Spray and spatula.
Spray so positioning is easy.
Only the middle Film has a slightly different terminal shape, but this does not appear to be a problem.
View detail
good product.
It's before riding, but the material and make are good. But the bottom brand part hole is not good. It was easy to attach and it was good to feel the resistance of the pad. View detail
![Tank Pad/Tank Grips [Pro]](https://img.webike-cdn.net/catalogue/images/67249/Suzuki-GSXS1000-2016-Black-Pro_TS.jpg)
You can feel the effect.
Without leather pants, my knees would slide forward even when I was gripping them, but now I can firmly grip my knees with Jeans without slipping.
The price is also relatively reasonable.
Double-sided tape can be used to attach the product quite strongly.
View detail
Position to come Exactly in Hang-Off posture
[How is it used?
Mainly Winding, mountain passes
Was the one you received as per Image?
Yes.
Was the installation difficult?
Since the pasting is FreeHand, the difficulty level is proportional to the person's personality.
How was your experience with it?
In the normal riding position, it hardly hits the pad, but in the Cornering posture with the hips slightly bent down, it hits the thighs EXACTLY and makes it easier to hold the body.
[Included Parts:were they on?
Alcohol for degreasing, ManufacturerSticker, LogoSeal, etc. are all included. The only other thing that would be nice to have is a masking tape.
[Was there anything that disappointed you?
Not sure yet how durable or how much it will deteriorate over time, but Grip was as good as expected.
View detail
If you don't mind doing your own processing, it's pretty good.
Grip feel is better than I expected. View detail
![Tank Pad Tank Grip [Pro]](https://img.webike-cdn.net/catalogue/images/40996/PRO730BL_01_TS.jpg)
Grip force
Grip power is very good, I chose PRO. View detail
![Knee Grip Perfomance [Black/Clear]](https://img.webike-cdn.net/catalogue/images/58833/EVO437CL_01_TS.jpg)
Eazi-Grip(EVO) vs STOMPGRIP(VOLCANO)
Quality and texture:Eazi-Grip Grip force:Eazi-Grip > STOMPGRIP
Eazi-Grip is made by die-cutting Large Seat and the cross section is left uncut, while Eazi-Grip is made by die-cutting Large Seat and the cross section is left uncut.
STOMPGRIP has a rounded cross-section and warts are not placed on the edges.
Eazi-Grip is gripped by both Material and warts, whereas STOMPGRIP does not grip as much with MaterialSingle Body.
The uncut cross section of the Eazi-Grip has an unpleasant snag because the wart is also severed.
The warts on the edges are better if they are cut off with Nipperetc.
The material itself is gripped, so dust adhesion and clothing dyes will stick to it.
So far I have been able to remove it with Parts cleaner, but I don't know what will happen as it deteriorates over time.
As I write this, STOMPGRIP seems better, but the reason I chose Eazi-Grip is because of its shape. (Paste position) It is
On ZX-6R, in case of STOMPGRIP, you need to have Rear Sets on or about 90cm inseam to have your feet hit the sticking position.
When purchasing, it is better to confirm which position you want the Grip to be in, and to confirm the photo of the sticking position firmly with Net.
View detail
Fits: KAWASAKI Ninja400, KAWASAKI Ninja250
Grip with Jeans without any problem.
Ninja400 (2020) Used for
The footpeg of Ninja400 was too low, so the footpeg was replaced with an external one immediately after purchase, and the footpeg was increased by 6cm from NORMAL.
This may be why there are no problems with the pasting points.
Height is 160cm.
View detail
![Tank Pad Tank Grips [Evolution]](https://img.webike-cdn.net/catalogue/images/38018/Suzuki-GSXR1300-Hayabusa-1999-2016-Black-Evo_TS.jpg)
Benefit from Knee grip support
I was worried about the Knee Grip Pad for my GSX1300R HAYABUSA (EJ11A) between OEMPad and this one, but I ended up choosing this one. The color and texture were better than I expected. The functionality of the pad is also good, as I can hold the tank firmly between my knees, and I felt that a knee grip support is a necessity. View detail
satisfying thing
It has a very good Grip feel to it.
It is easy to use because it did not slip on a rainy day.
View detail
![Tank Pad Tank Grips [Pro]](https://img.webike-cdn.net/catalogue/images/67249/Yamaha-MT-09-2013-2015-Black-Pro_TS.jpg)
Grip power is outstanding!
[How is it used?
Used in Main for city driving.
Was the one you received as per Image?
The Image was as shown in the Image, but there was a Package crush, which was a little disappointing.
Was the installation difficult?
Silicon-offSeat was included and installation was quick and easy.
How was your experience with it?
Grip force when knee gripping is excellent.
[Included Parts:were they on?
It was all there.
[Was there anything that disappointed you?
The range of hits is too small for the position I usually sit in.
It would be great if a Seat could be added that could also be attached to the Frame section.
View detail