【Eazi-Grip】Knee grip support TANK GRIP PERFOMANCE Review
I love it!
I am satisfied with the outstanding Hold performance and the Large change!
Responses
Other reviews
Easier Knee grip
This will be a reReview.
Immediately after delivery, only the side cover was attached, but later the tank side was also attached because the legs hit the tank side when the vehicle body is supported by the outer legs with the ass shifted, such as when driving on a mountain pass.
The positioning was done without any particular instruction manual, and the position of the legs was determined by straddling the tank, making sure not to miss the point where the legs hit the tank, and fine-tuning the position so that the line of the tank would be consistent with the line of the tank.
As with the Side cover section, when attaching, peel off the backing paper gradually to prevent air bubbles from entering, and apply it from the center outward in a way that releases air.
Although I am rather clumsy, I think I was able to apply it reasonably neatly.
As a result of driving on the pass, the Tank was well supported during Cornering and had the expected effect.
Especially in the forward leaning posture of SS, it is somewhat easier to support the upper body by having a good knee grip.
As I wrote in my last Review, [Color] Even though it is called Clear, I am a little dissatisfied with the Cream coloring.
A little more transparency would be nice without destroying the design of the car body.
View detail
Knee grip is easier and upper body fatigue is reduced.
I was going to use a Knee Pad to prevent slipping because my body shape is such that the Knee Grip is located at the side cover area, and I had used a Stomp Grip on my previous car and had a good feeling about it. However, the EasyGrip was selected this time because the range of the pad in the side cover was too narrow and it was not in the position I wanted.
Purchased PRO from shape etc. (Circuit) and the color should not spoil the Design as much as possible. [Color] I chose Clear.
I had compared the images with those of the G model up to the 2011 model, and I thought that there would be no problem installing it on the 24 model, and I was right.
Since there is no Instruction Manual for installation, I could not figure out the correct position to put it, but I put it at the position shown in the picture based on the Seat, Cowl shape, and the knee position when straddling the seat, etc.
Since there are protrusions on the surface and the Side cover is also in a phase, it is Large strange to install to prevent air from entering.
I felt like I peeled off the protective Seat on the back side little by little and managed to stretch it by pressing it from the Center toward the outside.
Despite these difficulties, the difference in knee grip between with and without the pad is enormous. Without the pad, I had to press my ankle against the heel guard to support my body, but now I can support my body at two points, my knee and ankle, which considerably improves my sense of fatigue even after running the same distance.
Currently, only the side cover portion is attached, but we plan to attach the tank side portion as needed in the future.
The only complaint is, [Color] It's a bit like Cream, even though it's Clear.
further [Color] It would have been better if it was Clear.
View detail
Great
As others have commented, it is a good product.
Grip force is very good and stable.
When we contacted the Manufacturer for instructions on how to remove and apply the product, we received SPIDI and detailed explanations.
I would like to buy the same product next time.
View detail
Less noticeable and high gripping power
[How is it used?
For ZX6R. For Touring and Circuit driving in Mountain Pass.
Was the one you received as per Image?
It was a Red colored LinerTape, so at first I thought it was a Red color, but I was wrong. [Color] It was Clear
Was the installation difficult?
After degreasing well, I put the pen in position before attaching. The work itself is easy, but once attached, it is difficult to remove, so I proceeded carefully. If air bubbles are formed, it will not look good.
However, there was no way to deal with the bumps caused by Cowl's Sticker, and some air bubbles appeared.
How was your experience with it?
I was torn between this and Stomp Grip, but I went with Stomp Grip because the warts are less noticeable and the Pad area on the lower side where it is attached to the Cowl side is larger.
The pad area on the tank side is not so important, in fact, it could be eliminated.
The Stomp Grip has a small pad area on the cowl side and was designed for relatively large-patterned people.
[Included Parts:were they on?
Seat for degreasing and Stickers are included.
View detail
Knee grip is easy to do, but Pants are attacked
PRO [Color] I purchased Clear. It makes it very easy to get a good knee grip.
On the other hand, Denim-type pants will be attacked and the pants will eventually tear.
Also, there are dye marks on the Pants (Parts cleaner will remove them).
Black would not have minded.
The edges of the Decal will remain airborne.
View detail