Reviews
Fits: HONDA monkey, HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey, HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey
GORILLA.
I replaced the Sprocket and the Nut was rusty and disgusting.
You haven't seen anyone?
Maybe so, self-satisfied.
It's cheap and Nut is a consumable product.
It would be horrible if it came off in a nudge or something.
View detail
I couldn't fit it on the CRF250L.
Can I fit a DRC Spo ROCKET before I buy it? I asked about it. Because word of mouth said it was Taper so I couldn't wear it and it was a waste of money! Of course I told them about the word of mouth. In reply this item is Large sturdy! It fits! I'm going to contact the manufacturer and ask for a picture of the product. Please send me a picture of the item and I will send it to the Manufacturer. → Please send it to me by designated courier service by cash on delivery. I've been waiting for 20 days....Moreover, they told me to remove the OEM and install it, but it was impossible for me to install it on my spare wheel. I stopped because it's a waste of time and fuel, I got an email apologizing and that's it. The products etc. are cheap and convenient to shop at, but what about this response? Minus 5 as a response to Shop rather than a product! Well, it's convenient, so I'll continue to use it, though! View detail
Fits: HONDA MONKEY
Changed from the same ManufacturerGold!
I used to use the same Manufacturer Gold Nut before, but the screw thread became wrong and this is the one I purchased a replacement It's light and looks great It's best not to close it too hard View detail
Taper bolts needed to fit the Sprocket
Since the KLX230R's OEMSprocket is a straight bolt Purchased to install a DRCSprocket
Quality is fine, no snags in the hand-tightening stage
The Hexagon Bolt was not easy to lick
Hang of the work hard to lick, Hexagon Bolt with a proper tool to the extent that it is held down and It is better to tighten it on the Nut side
You can have an OEM Taper bolt, but the cost performance is It's good and no doubt
View detail
I'm a bit of a wreck
I bought it for my KLX250
I use DRC's products a lot, and so does Sprocket
I felt like the OEM Bolt was getting sucky
I ordered it when I was on a side trip
View detail
Fits: KAWASAKI KSR1, KAWASAKI KSR2
The product was guaranteed to fit, but it doesn't fit
I bought it for the KSR2 and actually installed it, but the M6×16mm is the Quantity:Less than 2pc
M6× I had three too many 30mm
It was an expensive product, but I did my best to buy it because it was guaranteed to fit
It was a disappointment
It is currently being supported by We-Big, but the M6×16mm BoltQuantity:I can get 2pc
That would be most helpful, but..
View detail
Fits: HONDA MONKEY
If the price is a little lower, it's a good choice
I used the same product Gold as this one
You can remove and put it on and off every time you do the setting
Because I applied a little force when I tightened it, I ruined a Screwball mountain
I'm going to re-purchase the blue one this time
Since DrivenSprocket spacer is also installed, this time without washer I'll install it
(I'm changing the Bolt, which is a little long, but when I put in Washer, it doesn't take until the end to get the Nut
View detail
Fits: HONDA MONKEY
Just the right amount of tightness!
We did a RearDrivenSprocket exchange for MONKEY
I had to remove and install it about 3 times because it was a little bit displaced
One of the threads was ruined because I tightened it too much
Material:It's Aluminum, so it's better to tighten it appropriately
I'm currently a Gold Sprocket and will buy Blue again
View detail
Fits: HARLEY-DAVIDSON DYNAFamily, HARLEY-DAVIDSON SOFTAILFamily, HARLEY-DAVIDSON SPORTSTERFamily, HARLEY-DAVIDSON TOURINGFamily
Perfect for dress-up
I bought it to replace the Sprocket
The Chrome finish makes it perfect for dress-up
Of course, it's strong enough to be used with confidence
View detail
I'm impressed
Includes 6 Taper bolts and lock nuts for Sprocket mounting Quantity:Set。
Now I can install the Sprocket on my WR250 It looks rustproof and a very good buy
View detail
DRC's Sprocket
I bought the DRC Sprocket so I bought it, but the Bolt is flat while the Sprocket is flat Taper, the holes are governor, Garbage, I used the OEM one as it is View detail
Fits: HARLEY-DAVIDSON TOURINGFamily, HARLEY-DAVIDSON SOFTAILFamily, HARLEY-DAVIDSON DYNAFamily
Installation could not be done.
I attempted to install it at 1977 FXShovel but it was a little Large.. It is unknown whether the original one is an OEM, but there are also such things. Harley. View detail
No problem so far
WR 250X I exchange Bolt at the same time as Sprocket exchange of 2007 year.
I am driving without trouble for now without looseness.
View detail
Same as OEM
Sprocket's Flange nut. I also searched for Nut of the same shape not for Motorcycle, but because it does not change much, buy it here.
Lock nut so it will not be loose.
View detail
It is consumable parts.
Rear sprocket We exchanged at the same time when exchanging.
If this price is exchanged everything will not be regrettable.
Rigid feeling ? Fit feeling is also good.
All Quantity : Set so it's safe.
View detail
enough
OEM is too expensive when exchanging, so use this.
There is also a reputation for easy licking, but I think that work is probably only bad.
It's enough.
I have never Trouble so far.
I will keep using it for the future.
View detail
Pretty nut
It is a set of shine nut. Good quality. It make my bike become very stylish. Very nice coating. I am happy with that. Thank you. View detail
Renthal used for 48 Sprocket installation!
NORMAL's Bolt is 10 mm and Renthal 48 Duo Sprocket can not be installed, but this Bolt solves! Off car is a salvation Bolt who is supposed to think Renthal's big sprocket is cool! W View detail
It may be better not to rust.
I am glad that you do not have to loose Parts.
The item itself is also light and solid. Stable even when applying force close to twice the specified Torque. Breaker bar seems to be losing.
View detail
Very good
After replacing with Bore Ace's Sprocket cover, I was concerned about the rusted Nut.
When exchanging it, it makes us feel better..
Because it covers the entire Shaft, we do not worry too much about future rust.
Also, Washer comes with it, it is saved.
I bought it was a correct answer.
View detail