Reviews
Fits: KAWASAKI Z900RS, KAWASAKI Z900RSCAFE, KAWASAKI Z900RS, KAWASAKI Z900RSCAFE
I don't feel much.
I don't feel it much. I don't feel a huge change in the gear shift. I feel like the gear stops significantly when I go up from 1st to 2nd. View detail
photographic prints that you can take home with you
With OEM, the footpeg interferes with the footpeg when the foot is lowered, so I purchased this to eliminate this problem with Rear Sets.
There was no instruction manual and it was difficult to install. (Amateur work, about an hour for Small) The position can be adjusted from 4 levels,
Large Variety Satisfaction
View detail
I'm satisfied!
I like the look, the texture, and the build quality of OverRACING!
If I had to make a complaint, I would say that it would be better if the position could be selected a little more. Also, I wish the Instruction Manual was a little easier to understand, because when I follow the Instruction Manual, I end up removing the parts 4 to 5 times.
View detail
Fits: HUSQVARNA TC250, HUSQVARNA TC310, HUSQVARNA TC450, HUSQVARNA TC510, HUSQVARNA TE250, HUSQVARNA TE310, HUSQVARNA TE450, HUSQVARNA TE510, HUSQVARNA TXC250, HUSQVARNA TXC310, HUSQVARNA TXC450, HUSQVARNA TXC510
It also looks gutted and lowered.
The purpose of purchasing the Lowdown Link was not for footing or other issues, but to use the MOTARD vehicle completely as a road racer.
I put it on the picture, but I measured the ride height change from the rear axle to the exhaust system area, and it was 2.4 cm lower.
*This is not a correct measurement method and should be used only as a reference.
The amount of Front protrusion is also changed accordingly.
The look is now gutsy and low, and the atmosphere is to my liking.
It is important that you actually run and feel better.
Next, Spring rate will be changed after the actual run.
View detail
Fits: HONDA Today, HONDA Today, HONDA DIO(4Cycle), HONDA DIO(4Cycle)
Repair is completed at a low cost!
Installed on ThirdMotorcycle's Today that goes to the nearby Convenience, replacing an OEM OEMRear Suspension that had been scuffed up and deteriorated. The price is very low, but I have had no problems with it! I am Large satisfied with the low price and the refresh! View detail
Ride quality has changed drastically!
I was tired of the fluffy ride characteristic of OEM and finally replaced them with new ones! I am smiling to myself in the helmet because I can turn the curves on the mountain pass with a good feeling every time I make a turn! Once you install it, you will never go back to OEM suspension! View detail
I don't know.
Riding the CB250R, I thought, NORMAL footpeg, when I put my foot down.
The footpeg is just out of the way... sweat.
The CB250R really doesn't have a wide selection of kazutam parts.
And MORIWAKI
The instruction manual says to float the rear tire and pull out the shaft...
Sweat
CBs have a short sidestand that makes them lie down a lot, and when you pull out the Shaft, the Swing Arm shifts.
I had a lot of trouble doing it by myself, and if I wanted to do it by myself, I felt it would be better if I read your friend and we did it together.
I was afraid that the Motorcycle would fall over.
I would have chosen Silver for the Rear Sets because I am concerned about fading, but since the bike is Black this time, I decided to go with Silver.
Black is selected
It's raining today, so I can't ride, but it's nice to get back on the bike.
I would be happy if Shift feeling would change too.
Things are clean and Parenthesis is good.
View detail
More Classical
I replaced it with a new one that I thought would fit SR400.
It is secured with a single Plus screw, but it is aligned with the outside of the OEM's two Screw holes.
View detail
Fits: HONDA CB1000 SUPER FOUR (SUPER FOUR), HONDA CB1000 SUPER FOUR (SUPER FOUR), HONDA CB1000 SUPER FOUR (SUPER FOUR), HONDA CB1000 SUPER FOUR (SUPER FOUR), HONDA CB1100, HONDA CB1100, HONDA CB1100, HONDA CB1100 BLACK STYLE, HONDA CB1100 BLACK STYLE (ABS), HONDA CB1100 E Package, HONDA CB1100 EX, HONDA CB1100 EX, HONDA CB1100 EX, HONDA CB1100 EX <ABS> (Special Spec.), HONDA CB1100 RS, HONDA CB1100 RS, HONDA CB1100 RS, HONDA CB1100 <ABS>., HONDA CB1100 <Infinite Edition>., HONDA CB1100 <Type I>.
Replaced with a new one
Cheaper than OEM, but quality is sufficient to replace NTB nature
Stable quality.
View detail
Ride quality changes.
It arrived about 3 months after purchase.
I thought I might not be able to see much of a difference because of the use for city driving and touring, but that was not the case at all.
With the OEM suspension we had been using, there was a tendency for the car to bounce when stepping on the gap, and for the body to swing back and forth a large amount when breaking and re-accelerating, but after the replacement, these problems disappeared and the ride became very firm and secure.
Motorcycle is over 20 years old, so the same may be felt with OEM suspension OH, but we are very satisfied with the high quality appearance of this product.
Although not specified in this case, it appears that Lowdown and other Orders can be made at the time of ordering.
View detail
It is easy to install.
Installation takes only one minute! View detail
It is a quintessential KOOD product!
Smooth movement of the vehicle and lightness of the Wheel's rotation were immediately apparent after installation.
It is pricey, but I am glad I replaced it.
The Rear side was replaced at the same time as the Front side was replaced.
The appearance of KOOD products clearly shows how well they are made.
View detail
It is a quintessential KOOD product!
Smooth movement of the vehicle and lightness of the Wheel's rotation were immediately apparent after installation.
It is pricey, but I am glad I replaced it.
View detail
To replace genuine products
The original gear change lever has rubber rolled up in a roll shape, but since I frequently change gears, the front rubber often rattles, so I purchased a POSH product. I like the design of the genuine product more, but I like that this product comes in 2PCS. -------------------------------------------------- -------- The original gear change lever has rubber rolled up in a roll shape, but since I frequently change gears, the front rubber often rattles, so I purchased a product made by POSH. I like the design of the genuine product more, but I like that this product comes in 2PCS. Powered by Google Translator View detail
I am more then satisfied with the positive and direct feel now felt when changing through the gears
About quality and texture - The shift guide from G-Craft uses a sealed bearing unit and is made from billet aluminum with detailed machining and a silver anodized surface finish, the quality from the overall fit and finish is perfect. About the feeling of use - I was unimpressed with the overall feel of the original setup for the gear shifting as it felt vague. The transformation with the simple addition of this shift guide is amazing and I am more then satisfied with the positive and direct feel now felt when changing through the gears. Products to buy together - A product to purchase that will also ad in improved gear shifting is an adjustable shift rod that will allow you to perfectly position the gear lever to your desired position using the rest of the original rearsets. Difficulty of installation - The installation of the shift guide is a intermediate task that took 1 hour to complete. Some mechanical aptitude and the use of basic hand tools is what is required to secure the shift guide over the shifter shaft to the engine case. Cost performance and comparison with other products - I find the cost of all the products G-Craft sell to be on par when compared to what most other companies sell their products for but this is not the case with the shift guide as there are quite a few cheaper options available here on Webike. About shipping and packaging - With there being no cost difference between sea freight and EMS for the shift guide, I chose EMS for an earlier arrival date. The part was extremely well protected while being covered in bubble wrap and surrounded with air pillows in a sturdy cardboard box. Any concerns, cautions, or advice when purchasing - Webike Japan is the first place I look to for all my motorcycle needs. From service parts to performance products and even motorcycle gear and apparel, Webike always seem to satisfy my needs in regards to availability and pricing. View detail
Installed on JA10CUB110PRO
I wanted to do something about a Front fork that was too soft and bought one that was 10mm longer than the OEM Spring but would be usable.
As a result, the 10mm longer road was applied to the Pre-road, and the posture when riding became high on the Front and low on the Rear.
A YSS 15 millimeter long rear suspension was also installed separately to improve the balance of the car body.
I used Motul #20 fork oil instead of the specified YSS #20, which I have on hand, so I think the damping is a little weak.
I am very satisfied with the spring replacement because I have converted to a front disc brake and now I have a firm grip.
View detail
Costa's strongest?
I had no complaints with OEMNormal step, so I replaced only the footpeg with HURRICANE's one.:Pair (for Left and Right) I decided to purchase this product because it was inexpensive with Type, which uses Normal pedal.
The included instruction manual clearly explained the procedure for replacing the Brake Side for ABS vehicles, so I was able to install it smoothly.
Repair Parts was fully supported, the quality was good, and I was satisfied with the better parenthesis.
View detail
Higher than BABY FACE
Except for the footpeg and heel plate (and color), it is the same as BABY FACE. The cost is about 12,300 yen higher than BABY FACE, so the cost performance is not good. I am satisfied with the color and position.
The car Both SidesChange arm uses the original OEM Product, but of the 9 companies I checked, only BABY FACE and YOSHIMURA did not make a dedicated change arm. I was concerned that the shift rod was leaning, so I installed Striker's Change arm and adjusted it by 2mm with a washer, and it became almost parallel to the car body.
Well, I don't think there is anything wrong with it being tilted, but I am concerned about the way it looks.
Footpeg is made by JagerLauftK.M.T. I like it, so I changed it. Also, the Brake Switch Bulb on the Right Side looks like an afterthought.
I wrote what it is, but I like it a lot.
View detail
Thanks!
Thanks to the wide range of lineups, it is nothing short of a miracle to find an external suspension lineup on a 30-year-old and superb Minor car.
The performance is also better than the crappy OEMSuspension!
View detail
Fits: KAWASAKI Z1 (900SUPER4), KAWASAKI Z1-R/Z1-RII, KAWASAKI Z1000, KAWASAKI Z1000 MkII, KAWASAKI Z2 (750RS/Z750FOUR), KAWASAKI Z750FX, KAWASAKI Z900 (KZ900), KAWASAKI Z750FX, KAWASAKI Z1000, KAWASAKI Z1-R/Z1-RII, KAWASAKI Z1 (900SUPER4), KAWASAKI Z1000 MkII, KAWASAKI Z2 (750RS/Z750FOUR), KAWASAKI Z900 (KZ900), KAWASAKI Z750FX, KAWASAKI Z1000, KAWASAKI Z1-R/Z1-RII, KAWASAKI Z1 (900SUPER4), KAWASAKI Z1000 MkII, KAWASAKI Z2 (750RS/Z750FOUR)
Replace rusted Bolt and Cap Nut
The mounting bolt and cap nut of the rear suspension have rusted and were replaced to refresh them.
The replacement was done at the same time as the AxelShaft, so it is incidental.
It doesn't look much different at a glance, but I feel better when it is clean.
View detail