Reviews
I like it there!
it's for the cb125r, but I installed it on the cb250r as well! The part that holds the Visor may need to be modified (^^;)
Boltetc. was bought at Home center and painted by RubberSpray I painted it in
View detail
Fits: YAMAHA MT-09, YAMAHA MT-09, YAMAHA MT-09 SP, YAMAHA Tracer 900, YAMAHA MT-09 Sport Tracker, YAMAHA MT-09 Street Rallye, YAMAHA XSR900, YAMAHA Tracer 900
If it's a processing premise "Yes" (laughs) If you're going to use it as is None 。
I bought this for MT-09 2017
From the front, it's beautiful, but from the back, the BALI's cutting method is too crude and cheap I did
The connection part with the OEMRear Fender was connected without any discomfort, but the aforementioned BALI was not a concern I filled the connection part with Pate and painted it in OEM color after shaving It's a nice finish
If you buy it as a Base material for processing prerequisites "Yes" I think so
In the case of rain, mud splashes are no longer a problem for small rain, so it is effective I felt the
However, when we ran in the downpour, it was still a horrible mud-splattered mess, so the whole thing was It was only a slight improvement
View detail
Fits: YAMAHA MT-09, YAMAHA MT-09, YAMAHA MT-09 SP, YAMAHA Tracer 900, YAMAHA MT-09 Sport Tracker, YAMAHA MT-09 Street Rallye, YAMAHA XSR900, YAMAHA Tracer 900
Functionally, it's fine
It is generally what I expected
It's small, but it reduces the amount of water and mud splashed up to keep the dirt inside the rear fender in check It can be reduced
However, as far as quality goes, the end face is still sawed off, so if you accidentally cut your hand and You need to be careful because you might not be able to do so
It is advisable to round the cut edges with Sugar Crystal sandpaper before installation It is
View detail
Fits: HONDA VFR800X Crossrunner, HONDA VFR800X Crossrunner
In general×
I processed the return immediately after I arrived and opened the package
Installation/accuracy:I haven't installed it, but it's a 3Combo with paint peeling, BALI and Wound
Quality and Texture:Unbearable to see Level
Shape:I don't even want to look at it in detail
Feeling:unopened and unused
Cost performance:the cost performance is too bad in terms of quality
View detail
Fits: KAWASAKI Z1000, KAWASAKI Z1000, KAWASAKI Z1000 SX, KAWASAKI Z1000 SX
Mud splash protection after Fender Eliminator
Quantity:Pair (for Left and Right) s exhaust system and stopped at Bolt and Push rivet Remove the Inner fender; clean the OEMInner fender and put it in the middle Temporarily fasten and align this product using the pre-drilled bolt holes Use it to drill the holes for the Rivet that comes with it; there are four Rivets included, but they look It was going to be bad, so I'm going to use Quantity:2pc. I used only the set Once the hole is drilled, remove it and put it in Reverse side (Surface in contact with Tire) Degrease the
Double-sided tape is attached to the product, but in my experience, this kind of pre-pasted tape is not I don't trust some things, so I added 3M's Double-sided Tape for super-strong external packaging You can install it without any gap After fixing it with both sides and Plastic Bolt and Rivet, you can install it to the car in reverse order
You can extend the Fender by about 15cm, and it will be finished like an OEM Mud splattering in the rain is more common than with Other Brand Products that replace the entire fender I think it will have an effect on
View detail
Fits: BMW S 1000 RR, BMW S 1000 RR, BMW S 1000 RR, BMW S 1000 R, BMW S 1000 R
It's better than a material than a material,.
It is an ABS Plastic item of Carbon's appearance, which looked like Carbon, but I bought a willingness to buy because of this design nature and the goodness of making the details.
It was awesome to see! If you want greedy, it would have been better if you let your shape be able to hold the Rear brake line.
When attached with Fender Eliminator, it is pretty wonderful!
View detail
BODY STYLE front fender extension
The product seems to be made from decent quality plastic and is molded to fit the front fender of the 2017 Suzuki SV650 ABS. Instructions included are in German and comes with 4 tiny snap-on fasteners which need to be drilled onto the fender. Not wanting to drill holes, I instead attached the mudguard using the 3 double sided-tape already attached to product, although I think that wouldn't suffice so I stuck more 3M double-sided tape for extra insurance. In hindsight, epoxy would've probably worked better. Time will tell if this thing holds. IMHO, this product is over-priced for what it is. View detail
It's expensive
The price is high for a non-Carbon I regret that I would have been better off with Magical racing The only good thing about it is that Parenthesis is a nice breeze … installation is a problem It's probably the only thing that's keeping me alive View detail
Satisfied w
Thick Color : It is a firm build with UnpaintedABS. It is divided into two with Chain Guard. Although the attachment part of the Exhaust System side is Tie Wrap fastening to the Base of Double-sided Tape, it is easy to install firmly because it is easy to build. To install the Chain Guard remove the footpeg. Bolt On can be done to a degree that one hole has been expanded.
Since I can do work pattern painting free of charge, I bought without trouble, but if I ordinarily asked Kotetsu shop, it costs 10000 ~ 20000. Probably w
View detail
Fits: BMW C 650 Sport, BMW C 650 Sport, BMW C 600 Sport
Inner fender falls short
I'm debating if this fender is worth $200 when it barely covers up just a few inches above the swing arm. What happened to inner fenders that actully cover the tire?? View detail
It became a good feeling with unity with Body color
I wanted to purchase it with the same product of 17 year NINJA1000, but because it was a complete sale notation, I bought it with daring, as it is possible to install it for Z1000.
As a result I was able to install it without any problem in mounting.
Body color and unified feeling comes out, it is good for the appearance Accent, and the OEM ratio also improves the function.
I am very satisfied..
View detail
Fits: BMW S 1000 R, BMW S 1000 RR, BMW S 1000 R, BMW S 1000 RR, BMW S 1000 RR
Is it supposed to be a price ρ (т ωт`) イジイジ
I thought that the extension part and the parts that fill the mysterious hole of OEMInner fender were connected, but it was a separate part.
Installation Instruction Manual comes with, but in the Instruction Manual for Front, in addition, German ('? Ω ? `)
Since I can not use it, I will attach it by my own interpretation (ω - ´★)
View detail
Fits: SUZUKI GSX-R 1000, SUZUKI GSX-R 1000, SUZUKI GSX-R 750
Design buffer
It falls to FenderBattery case which was lowered and attached before
I bought a BodyStyle price is high but Design?
Although the design is slightly different from the photo
90% for Battery case
I installed three holes like Tie Wrap for installation.
Product is Material color.
View detail
Fits: BMW S 1000 RR, BMW S 1000 RR, BMW S 1000 RR, BMW S 1000 R, BMW S 1000 R
feel well.
I mounted it in S1000RR for 17 years.
Bolt position was also able to be mounted easily with high accuracy.
I feel more powerful than NORMAL and I like it with Race ish feeling.
View detail
Fits: SUZUKI Travel Edition, SUZUKI GSX-S 1000 GT, KTM 1290 Super Duke GT, KAWASAKI Versys 650, HONDA NT1100, DUCATI Multistrada V4 Pikes Peak, DUCATI Multistrada V2S, DUCATI Multistrada V2, BENELLI TRK 800, BENELLI TRK 502 X, BENELLI TRK 502, KTM 1290 Super Adventure S, KTM 1290 Super Adventure R, DUCATI Multistrada V4 S Sport, DUCATI Multistrada V4 S, DUCATI Multistrada V4, HONDA NC750X, YAMAHA XSR700, YAMAHA Tenere 700, DUCATI Multistrada V4 Rally
For Fender Eliminator?
It was doubtful that the corresponding model was abnormally large, but it was understood that the item arrived.
How to install Direct attachment with Double-sided Tape to the back of Number.
Material included : PlasticScrew (Diameter about 5 mm) And Nut is also available, but to use it has a long base plate below Number
Drilling is necessary.
Product is Material : Since it is not heavy in Plastic, even in a state like Direct pasting, if it is degreased and the surface of laminating is sufficient
It seemed not to be peeled off.
Since Double-sided Tape has already been pasted, peeling off extra parts is a hassle when attaching to Plate like photo.
Moreover, it is better to change the thickness of Double-sided Tape because Screw makes it easier to open the top lamination.
I installed it with NORMAL's Fender, but as if the width got wider as I looked behind
It seems that there is no point that the clearance between the other and the original Fender is Large and it seems to be visible.
If you do not devise any way to use it, you will hit each other with vibration and rattling sounds.
It is subtle whether people interested in Fender Eliminator are interested.
View detail
seems not fit HONDA CB500X
the hand guard collide with the windshield at the end turning. And there is a lot of free-play not fixed as firm as I expected. I then have to remove it to change another one! View detail
Fits: BMW R 1250 RS, BMW R 1200 RS, BMW R 1200 RS
Satisfied with price
I tried buying it by comparing the price with the competitor's product.
Paper File, adhesive, cleaning cloth was also included.
It is satisfying to purchase cheaply because there is no Large in the function.
View detail
Looking from the front ... ... White ??
Protecting the whole product Seal is being done and I am doing it as a chitin.
Four Screws and NutQuantity : 2pc. It is attached only by the exchange of Set, there is neither Gap of the Screw hole nor the match with the vehicle body resin Color, it has no discomfort
Cost performance is ... star 0
I want a personality different from the others, unable to buy unscheduled gold when it does not happen
View detail
Fits: KAWASAKI Z1000 SX, KAWASAKI ZX-10R, KAWASAKI Z1000 SX, KAWASAKI Z1000 SX
I am very satisfied.
It is necessary to drill the existing Fender and process the attachment part of the Brake line fixing Gold tool.
If you are not confident, you may as well leave it to PRO!
How to get dirty by rain running will be considerably reduced.
Looks also seemed to have come from the beginning!
View detail
As one of the options
This product is thick enough not to distort by wind pressure
Because the protection Film was in the state
The impression of quality was good.
Foreign products are rich in many things ...
Although windproof, it is the shape that the running wind hits the index finger while holding the Grip.
Because I am away from Grip, there is winds involved, but I think that the effect was good.
Grip heater, electrothermal Gloves, Handlebar Coveretc.
I wish I could be one of combinations and options.
Since the part which becomes outside the car body with replacing NORMAL part is only big Large, I think that Clearance at the time of Full Stare is no problem, but people who are changing Screen or Handlebar need Small workmanship It may be.
I am changing both, but I just finely adjusted.
View detail