Reviews
No problems with compatibility, no complaints if Screws and Nuts are included!
The OEM inner cowl was damaged and I had to replace it (the front of the knee was broken when I straddled the cowl). Meter Material:Carbon Style and the look and feel of the product may be more like a Match than an OEM. View detail
A-tech single seat cowl&seat
Received my single seat cowl and seat today and I'm very impressed with the quality of the items,I've offered the cowl up the the bike and the paint is a good match, the only reason it's not getting 5 stars is the time between buying and receiving the item. View detail
Quite a sense of Upgrading!
The installation required removing the rear of the Exhaust System, but either way, the ScrewQuantity:The work was only increased by 2pcs, so it took less than 30 minutes.
The appearance of the upgrade is great, the feel with the tire is even, and the precision is perfect.
Basically, we will not run in the rain, but we will consider installing a Fender Eliminator depending on how far we can prevent Tunnel and other springs from splashing up.
View detail
Lots of interference.
Purchased to prevent stains rather than to receive Oil.
Material:It is made of FRP and weighs 580g.
As is, there are no nests or hickeys, but there are many Small scratches and scuffs, so it is painted.
Lightly polished with #1000, sprayed with a buffing compound, and painted with 2-component urethane.
Cut because it interferes with Bracket and Hose near Side Stand, although it is not mentioned in other reviews.
Cut because it interferes with the IndonesiaFull Exhaust System that is being installed.
It was difficult because there were many parts to cut and a lot of cutting.
Prepare cutting and cutting tools for those who purchase them, as they are difficult to use with manual tools.
View detail
Difficult to install
Installed to prevent dirt. Selected because it was a good looking shape similar to SBK among various companies.
It is made of FRP and weighs 390g.
There are Small scratches and scuff marks on the surface as it is.
There were no nests or sink marks, so I lightly sanded the paper with #1000, sprayed it with a buffing compound, and painted it with 2-component urethane.
The OEM Fender has a hose through the hole, so it cannot be removed without removing the Caliper or cutting the Fender.
Cutting the inside is not noticeable, so it is cut and removed.
The collar had to be attached on the inside, so it was difficult to align it, even more so since there were so many things to overlap since I had also attached an under rear fender.
And since the collar for the front hosebracket is not included, I am worried that it might get twisted when tightened.
Sponge is included to prevent the bracket from rubbing, but it is better to have a separate rubber plate since it is likely to be scuffed and ruined soon.
The shape is good, but it takes a lot of care to install.
View detail
The delivery time is still long,..,
Sharp STD shape is good, but rounded SPL is even better parenthesis.
The delivery time is −1 because of the long delivery time.
In the end, we waited more than six months.
View detail
Effective against heat
Purchased for heat protection.
Material:I thought it would not be a perfect Fit since it is a Carbon product, but it is perfect except for the footpeg area.
It also blocks heat and is comfortable in the summer.
View detail
Used as Oil receiver for Circuit run
I installed it on my Ninja 250SL that I ride for Circuit Racing.
Since it is a dedicated product, it can be basically simply installed, but there may be some interference depending on the exhaust system being used.
I had OEM Exhaust System and YOSHIMURA Slip-on Silencer, but there was a little bit of shaving part.
View detail
Fits: SUZUKI GSX1300R GSX1300R HAYABUSA(GSX1300R HAYABUSA)
Fairly reasonable price
GSX1300R GSX1300R HAYABUSA Installed on a 1999 model
I don't know what the impact is, but the price of carbon parts from various companies has skyrocketed. (or rather, no longer rampant). In the midst of this trend, the Carbon rear fender can be purchased at a price that is sensibly comparable to conventional fenders.
I don't know if the price is actually going up or not because I don't follow the market.
Design is as you see it.
It covers the rear tire as a rear fender and also covers the drive chain.
There is no problem in terms of accuracy, and if you are not particular about it, it can be ponned as it is.
Personally, I didn't want to damage the Swing Arm, so I put Sponge on the contact surface. I felt guilty about tightening the Carbon directly with the Bolt, so I enlarged the Bolt hole to M8 and installed it by floating it with an M8→M6 conversion collar and RubberWasher, I installed the bolt with some minor modifications.
Functionally, I do not know because I have not yet driven in the rain, but as a Fender, the width is narrow and the antifouling function is a little unsatisfactory.
However, the appearance is SMART for that reason.
The GSX1300R HAYABUSA does not have a Rear Fender in OEM condition, so the Rear view is uncomfortable, especially when the Exhaust System is changed to Single Silencer.
In addition, the difference in texture between the adjacent chain cover and the resin is a concern with many carbon rear fenders, but this product can also serve as a chain cover with just one fender.
So, it is an excellent looking custom product.
The Neck is a Tie Wrap fixation, but there are no screw holes that can be used to fix the Tie Wrap in the first place, so that point is unavoidable.
This was also the first time for me to purchase A-TECH carbon parts, and I was not disappointed with the quality of the carbon.
I think the quality is on the high side, as even Brand products from well-known places can be disappointing.
Although you will probably have to wait for a certain period of time after ordering because it is made-to-order, you should first be thankful that they still lineup custom parts for motorcycles that have been on the market for almost 25 years.
And the price is relatively reasonable. (This is only based on recent trends.)
I can fully recommend this product to others.
View detail
It takes quite a while to reach the..,
I had heard rumors that they are a manufacturer with a long delivery time, but I wonder how they are doing as a manufacturer in this day and age if it really takes this long. It is not like electronic parts.
As a result, satisfied with the product.
Outside of supported model year (2BL-PC40) Screws can also be fixed to the limit. However, there is some interference with Cowl and Rear Sets. (Exactly with no Clearance) 。
View detail
For Dress-up
I don't race or anything, but it looked cool, so I put it on.
Since we did not feel the need to use carbon, we chose FRP, and the weight was about 650g.
There were some nests and wrinkles, but they were not exposed, so they were painted with Urethane Matte Black.
When I purchased the company's Under Cowl for 10R in the past, I was careful to handle it with Pe LePera, but this product has many rib-shaped folds and lines with the same thickness, which gives it a rigid and solid impression.
The 10R was not shaped in line with the frame and was prone to cracking, but this product is shaped to fit the cowl and frame firmly, which is a good thing.
The fit is good, but the hole for the well nut was gapped by half a child, so I corrected it with File.
The Cowl is covered from the front edge to the rear tire, which may have a rectifying effect.
The Rear Suspension Link area, which was hidden by the lunch box due to the installation of the Full Exhaust System, is now exposed, and since the engine area is also covered, it is likely to have an anti-fouling effect.
The thermal barrier Tape that comes with the product has a minimal area, so it is better to purchase an additional one.
A little more volume at the rear end would have been better.
View detail
Role of car model compatibility information
The rear inner fender of my GSX-R1100K was getting old, so I bought a new one from A-TECH.
Since it is FRP, I am very satisfied with the lightness as well as the quality of the texture. Except for one problem….
The size of the Chain Cover is not wide enough for the 160 tire width, and the Chain Cover is gapped on the outside.
I am not thinking of returning it because I have given up on the idea of using it for other vehicles if I can use it because it is an old car now.
However, when I ordered a Front Fender, I received an 18-inches for the first half of the year on a 17-inch K-type. (Processed) What is the meaning of the car model compatibility chart that you select when ordering? I honestly have a feeling that it is not a good idea.
View detail
Fits: SUZUKI GSX1300R GSX1300R HAYABUSA(GSX1300R HAYABUSA)
I purchased this product for both heat protection and dress-up.
The fit is slightly floaty….
However, it looks like Carbon and is ideal for dress-up!
I bought it for heat protection, but I don't know how effective it is because the temperature doesn't go up where I live this time of year, but when I touched it after coming home, it didn't feel so hot, so I think there is a big difference between having this Cover and not having it!
We will continue to use the product as is!
View detail
Chain Guard
The system was installed in order to comply with Circuit's vehicle regulations.
The Bolt holes were easily installed without any misalignment, etc.
The gap between the Bolt and the Sprocket is narrow and there is no interference, but a shorter Bolt would be better.
The protruding corners look bad.
View detail
Some processing is required.
Overall, the product is of good quality, but because it is FRP, the holes were misaligned in some places due to deformation and needed to be corrected.
Although it fits the Upper Cowl effectively, I was a little disappointed that there is a large gap between it and the Guide wing.
View detail
NinjaZX-10RRCarbon SeatWing
Normal, which does not fit in at all, has a Large keyhole, so it is naturally processed by File.
I have been purchasing a wide range of A-TECH Carbon products from exterior to Mirror for a long time!
Quality is commercial Material:It is No. 1 among Carbon products.
View detail
A-TECH's Core guard is Parenthesis good!
Little Quantity to fit the Radiator type:Pair (for Left and Right) Just angle it and replace it with 4 Bolt.
It prevents stepping stones and looks good Parenthesis!
I personally like A-TECH's Mark very much!
It was the right choice for A-TECH!
View detail
First plain weave Carbon
Carbon parts have always been twill weave, but this time, I purchased plain weave Carbon for the first time because it was in stock.
I am satisfied with the presence of Carbon parts.
Position is also improved because it is backed 50mm back!
View detail
Safety.
Purchased to match Race regulation.
Installation itself is simply tightened with a bolt, but be careful not to overtighten.
I would like to see a Torque notation.
View detail
It adds to the atmosphere of the Custom car.
Here is an imprementation for a '90 C ZZr1100.
Meter panel is Color for C-type ZZr1100:Unpainted resin is obviously cheaper than the D-type, and when exposed to ultraviolet rays, it becomes white and has a texture that is hard to look at. The resin can be kept clean to some extent with regular use of a resin luster revival agent, but it is a 30+ year old motorcycle to begin with, so … it is not a good idea to use a resin luster revival agent.
I decided early on when I started riding my ZZr to get the Carbon Meter Panel from A-TECH, and I'm glad to see that they produce handmade exterior parts for 30+ year old Motorcycle's. I have no choice but to buy it.
So I placed an order with Webig in February, but the delivery date was mid-August, six months later. Well, we are not in a hurry, so we waited patiently, but half a year is a long time no matter what we think.
The parts we received were beautiful plain weave Carbon, and they were solid. [Color] The installation work was done by myself. The installation work was done by myself. Although the assembly accuracy was not as good as the OEM parts, I did not have to file the screw holes to make them larger. I was happy to see that the installation was completed without any modifications to the screw holes, which I had expected to be done by machining. If I wanted to perfectly match the chili, that would be a different story, but for now, I am satisfied with the results.
I like the carbon inner panel because it gives the car a custom look and feel. It looks very cool. It is very cool.
The only drawback is the delivery date and the small window to access the reserve tank for Coolant. A-TECH's Small window cannot open the Reserve tank lid, so it makes no sense at all. If you just want to inspect it, just shine a light on it. Well, Coolant replenishment is not a work to be done so frequently, and I dare to say that there are some drawbacks.
If you have a C type ZZr1100, it will give you a great atmosphere. Personally, I am glad I bought it.
View detail