Reviews
Easy to Ime Chain
I want to brighten up the Tire section a bit,
To match Body's Red.
MDF Mirror red 6mm is attached.
I forgot to buy the Sticking Gauge for Rim Stripe, so I'll put it on by feel.
Well, I was able to do it just fine.
View detail
MDF Rim stripe 4M Red
Used for 10Inch wheel of ADDRESS V100
Selected because it was good to use it on the GSX-S of the Main vehicle.
You can choose the width of the rim sticker according to the vehicle Image.
This time, 4mm width is recommended as it tightens the foot.
View detail
It's easy to paste.
I used it on my friend's Scooter. After degreasing and applying it properly, it did not come off even if I washed the car hard. I used to put a cheap product from another manufacturer on my friend's Scooter and it came off in less than a week! View detail
Due to budget constraints...let's start with Shroud.
[How is it used?
I wanted to Refresh Shroud, which was full of scuffs and scratches and was given to me by a friend, It's OEM Decal." I purchased a Graphic decal made of MDF, which is less uncomfortable to say.
It was too tight for my budget to buy a full set, so I decided to buy a quantity this time.:Pair (for Left and Right) Only the Shroud section of the
Did you receive the item as per the Image?
Decal is thinner than FACTORY EFFEX, but slightly thicker than OEMDecal, and is expected to be more durable.
MDF's Decal system was previously used for KLX125 and RimDecal, so I have a sense of security.
The product was just as per Image with just the right design, not too flashy and not too plain.
Was it difficult to install?
This kind of work... has a strong sense of tedious work rather than difficult work, and I am Quantity:Pair (for Left and Right) It took about half a day just to apply two sheets, including the adjustment of the position of the "A" and "B".
If you are familiar with the process, you may be able to do it in 30 minutes~1 hour.
How did you like it?
The decals are of high quality with no gapping of the molds.
The adhesive strength is high, and if it is applied firmly at first, it will hold up to high-pressure cleaners better than OEMDecal, so it is easy to use. (It is not absolutely impossible to peel off. Please keep in mind moderate spec.) It is easy to wash the car after playing in the mountains.
As mentioned above, the adhesive strength is so strong that it can adhere without any problem even on top of scratches on the shroud, etc., and the difference between the scratches is not noticeable, making it ideal for concealing wounds. (This does not apply to deep gouging Woundetc.) 。
Was "Included Parts:" attached?
Only Decal is taped to a cardboard to prevent it from losing its shape, so please peel it off before working on it in the mansion.
Were there any disappointments?
No personal.
Although the pasting process is a little Large strange when you are not used to it, the hard work will be rewarded when you see the finished exterior.
Other items that would be helpful
Point and hang of installation
Work slowly and unhurriedly in a dust-free environment.
Spray the backside of the Decal and the object to be attached with a mist spray diluted with a neutral detergent, and position the Decal and the object to be attached by displacing it, and then remove any air or moisture that may have entered between the Decal and the parts little by little.
I think it can be applied beautifully without wrinkles by applying heat to curved surfaces with a dryer or similar tool.
In advance on YouTubeetc. Motorcycle Decal Paste. I think you can work with even more confidence if you check out the video by searching for (MDF's video is also attached around the middle of Webike's product introduction section) 。
[Availability and clarity of the Instruction Manual
Instruction Manual is included with illustrations.
But as I mentioned above, if you watch the video and then take on the challenge, you won't need the Instruction Manual.
[Notes]
Object to be pasted (Shroud and Side coverretc.). Clean and degrease the surface of the "P" before attaching it.
The rest of the work should be done as described above, referring to the video.
[ITEMS TO BUY TOGETHER
Chemicals for degreasing (parts cleaner, silicon-off, etc.), spray bottles for misting, rubber spatula for degassing & dehydrating, etc., will help you to work smoothly.
[Opinions and requests to Manufacturer
I am fully aware that it is a good product, but it would be even easier to purchase if it were a little cheaper.
View detail
For those who want one point for the suspension...
I am a Rim Sticker Large lover, so I have applied Large stickers on my motorcycle for many years, but I always buy MDF's split type stickers because I think they are very good and easy even for an amateur like me.
When you look at it up close, it may not look like a nice circle, but when you look at it from a distance and while the tire is rotating, it already looks like a large body circle, so it's OK! I put it up with a forgiving attitude.
View detail
I appreciate that they can be purchased individually.
[How is it used?
This product was purchased to refresh WR250R, which has more Small scratches due to playing in the mountains.
Decals for each Part are sold individually, so you can choose the Quantity:I appreciate the ease of being able to purchase Sets and RoseRose.
Was the one you received as per Image?
The thickness of Decal is a little thicker than OEM, so it is easy to apply and seems to be durable enough, which is promising.
The product was just as in Image with good design and color.
Was the installation difficult?
More than difficult. "A tedious process." Sense is strong and Sense and patience are tested.
I don't have Sense, so I had to work only with patience and it took me about an hour just to put it on the Swing Arm...
How was your experience with it?
The decal was finished to my great satisfaction, with no gapping of the mold and high quality of the decal.
The Decal itself is also durable, so there is no tearing or peeling after a few falls (although it is hard to hit obstacles because of the Swing Arm where the Decal is attached).
It has high adhesive strength, and if it is applied firmly at first, it can withstand the water pressure of high-pressure washers better than OEMDecal (it is not absolutely impossible to peel off. Please keep in mind moderate use), making it easy to wash the car after playing in the mountains.
As mentioned above, the adhesive strength is strong, so if there are some scratches on the exterior, etc., it will adhere without problems (to a certain degree), so it is good for concealing Wound.
[Included Parts:were they on?
Instruction Manual for Decal and pasting is enclosed.
[Was there anything that disappointed you?
The hard work is rewarded when you see the exterior of the product after it has been applied.
Other items that would be helpful
Point and hang of installation
Work slowly and unhurriedly in a dust-free environment.
Spray the backside of the Decal and the object to be attached with a mist spray diluted with a neutral detergent, and position the Decal and the object to be attached by displacing it, and then remove any air or moisture that may have entered between the Decal and the parts little by little.
I think it can be applied beautifully without wrinkles by applying heat to curved surfaces with a dryer or similar tool.
MDF has a YouTube video site that shows how to apply Decal (you can also check Webike's product introduction section), so you can work with more confidence if you watch the video before you start the process.
[Availability and clarity of the Instruction Manual
As mentioned above, an Instruction Manual on how to apply the paste is enclosed.
Well, I don't think you need Instruction Manual if you watch the video before taking on the challenge.
[Notes]
The surface of the object to be applied must be degreased thoroughly before applying the adhesive.
[ITEMS TO BUY TOGETHER
I think you can work smoothly if you have parts cleaner, silicon-off, etc., chemical for degreasing, spray bottle for spraying, rubber spatula for degassing and dehydration, etc.
[Opinions and requests to Manufacturer
Quantity:I would appreciate a little more savings on the purchase of Set, please.
View detail
Newer homes are better.
I had a used MOTARDWheel that I had to replace the Tire, make it Tubeless, and even replace the Spoke for rust on the Spoke nipple, because I got to the point where I couldn't back out of it,
I've already decided to add Rim stripe to make it Beauty by the way.
Rim wounds were smoothed with BlueMagic. After that, degrease with Brakes cleaner.
As when I pasted MDFRim stripe before, I cut the entire base paper into strips and pasted them with FreeHand without using detergent because I wanted to avoid moisture as much as possible because of the hollow wounds.
After all, it was easy to paste Stripe while removing it.
The stripe is not smooth in some places due to some wounds, but since it is a used wheel, it can't be helped, so we have to put up with it.
I think the new home will be more Beauty, and I think it will also prevent Wound.
work process
1 Smoothing by gentle Gold genus polish.
2 Brakes cleaner is used to degrease and wipe down the surface three times to complete the surface preparation.
3 Cut Stripe into strips.
4 Position the Rim and attach the end about 2CM.
5 While holding there and peeling off the base paper, pull up the one to be positioned at an angle of about 30 degrees, and crimp it while holding it with the other hand.
Overlap the overlapping area by about 1.5 CM, press down again, and start.
Finally, Finish while inspecting for air bubbles and floaters while pressing down with the thumb.
Lately, I have been doing it this way without Gauge.
tools used
Compound and Gold polish, Brakes cleaner, Bent Scissors (Kyosho's well-known polycarbonate body for radio control - Scissors for cut) White Driving glove.
I felt that Takasago's ExcelRim was better for Off-Road's 15mmStripe because it didn't have any indentations or anything.
View detail
The rugged black wheel has a little bit of color, don't you think?
The vehicle is NT1100 White.
I think a delicate design is more suitable for this motorcycle than a sporty design,
We selected 4mm White.
The folded portion of the special affixing Gauge was slightly modified to fit the full circumference of the Rim.
Even though I am clumsy, it turned out beautifully, almost like it was supposed to.
It also comes with three Manufacturer Stickers, which is a nice touch. (I'm glad).
The secret is to use a thin detergent water as per the instructions, and it can be reapplied two or three times on the spot.
The large size is sturdy and durable, so there is no need to panic even if the laminate bends. Spare parts are also available in quantity.:It also says "1 Set of 2pc.
View detail
as if it were indispensable
It's so simple, but it's such a good Tool that I don't think I could do without it.
There is a video from the Manufacturer on how to use it.
View detail
Easy and stylish!
Fashion starts from the feet up, as they say!
I was torn between Lime green and Titaniumium color, but I chose Titaniumium color because it does not look like OEM.
It is easy to apply and I think you can enjoy Fashion easily!
I used 6mm this time, but next time I would like to try 10mm for more impact!
It is strongly recommended to use MDFOEM's Sticking Gauge for Rim Stripe!
View detail
Most convenient!
Cheap and easy, anyone can apply Rim sticker beautifully.
It's a great costumer!
However, be careful not to fold the front and back too many times or you risk breaking it! (!)
View detail
Easy to work with
I used this when I pasted Rim tape, and I was able to paste it without gapping. It is inexpensive and I think it is worth buying. View detail
Parenthesis better
The rim tape makes my feet look tighter and improves parenthesis. I love it. By carefully cleaning and degreasing the rim surface where the tape is attached, the tape adheres properly. The rim surface was attached properly by carefully cleaning and degreasing the rim surface. It took about an hour and a half from cleaning to completion, since it was my first time. I am worried about the durability, but it is cheap, so if it peels off, I will just put a new one on. It will be strange to peel off the old one, but.... View detail
High quality and OEM-like cohesiveness.
[How is it used?
I bought a used KLX125 exterior for mountain fun, but it was only black, and I wanted to put some decal on it, Bloody." Fire a." A Tucker." and three types of GraphicPattern, this time A Tucker." I ordered a
Was the one you received as per Image?
I purchased the product as shown in the image because I checked each Pattern on MDF's website, where there are images of the product pasted on each vehicle.
Was the installation difficult?
・・・To be honest, it is a tedious process.
1. thoroughly clean and degrease the object to be affixed.
2. Fill the empty bottle of the spray gun with diluted neutral detergent solution water and spray it evenly on the surface of the object to be pasted.
Peel off the Decal from the backing paper and place it on the object in place.
4. push out the neutral detergent water between the object and the decal with Rubber spatulaetc. after finishing correcting the position.
5. Decal that floats on the surface is lightly roasted with a dryer or the like to make it adhere to the surface.
6. When you get a good feel for 4 and 5, proceed to the next Decal work.
After the work is completed, leave Decal until the adhesion of the glue surface is stabilized, and then install it on the vehicle.
It is difficult to understand in writing, so please watch the video of the work on MDF's Site or check the videos on YouTubeetc.
I worked on it while referring to the video of the work on MDF's Site,
How was your experience with it?
The joy after the hard work of pasting is unmatched.
Especially in my case, relatively docile. A Tucker." MODEL was chosen, so after the work was completed Was this Coloring's MODEL from Manufacturer?" It is so uncomfortably integrated that it seems like a good idea.
[Included Parts:were they on?
Decal and Instruction Manual for the application work are included.
[Was there anything that disappointed you?
It is not a disappointing point, but the difficulty at the time of pasting and the cohesiveness after the completion of the project. It's harder to play in the mountains." There is a point.
Other items that would be helpful
Point and hang of installation
As I mentioned above, the best way is to check it out on video.
My personal opinion is. We'll take our time and work our way through it." is hang? I think so.
[Availability and clarity of the Instruction Manual
Instruction Manual is included in the package, but I think it is faster and easier to understand by watching the video.
[Notes]
You may want to work in a tidy indoor area, as you will want to cry if grease or dust gets on the gluing surface.
[ITEMS TO BUY TOGETHER
Rubber spatula makes draining easier, so it is a good idea to purchase one at 100-yen stores, etc.
[Opinions and requests to Manufacturer
Please continue sales for vehicles that have been discontinued as much as possible.
View detail
Parenthesis is even better than I imagined!
[How is it used?
Purchased for makeover of vehicle body.
Was the one you received as per Image?
It was thicker and more solid than I expected.
Was the installation difficult?
I think it takes time, tools, and sukill to paste it nicely.
How was your experience with it?
I am very satisfied with the "Large" product, which is much more immeasurable than I had imagined.
[Included Parts:were they on?
We recommend purchasing Squeegee separately.
View detail
easy to stick to
It is easy to apply because of its thickness and solid shape.
A misting spray with mild detergent and parts cleaner are required for installation. It is better to use a separate guide for more beautiful installation.
17in. is applied by overlapping each other by about 2 cm, so that the color and Logo are diagonal.
I thought the light reflection made it look like 7 colors, but it is actually Gradation.
Rim sticker is a Commendation by MDF
View detail
Definitely buy it.
I thought it was paper, but it is Plastic.
Mist spray and don't mind getting wet.
If you want to put a Rim sticker on it, definitely buy it.
View detail
If you want to change the look of the Wheel area, this is the way to go.
The appearance around the Wheel and Tire will be Active.
The pasting process is not difficult at all. I have Repeat many times.
When working, don't forget to use a mist of diluted neutral detergent and Squeegee.
For those who want to easily change the look and feel of the product, this is Recommendation.
View detail
I forgot to post the image so I reposted it.
[How is it used?
I built a Wheel for SEROW225WE for street riding, but it is in a somewhat disappointing condition for all the trouble I went through because I built a scratchy Rim on a used Spoke from Stock.
After assembling IRC's GP−210, I put on the MDF Off rim stripe 15mm that I had ordered from Webike.
The harmony of the front and rear Wheels and the body of the car looks very good.
Was the one you received as per Image?
I have been using MDFGraphic's Logo since it was the old Type, so the product was just like Image.
Was the installation difficult?
The process is tedious but not difficult and requires patience.
Refer to MDF's website.
Degrease the area where the rim is attached firmly with Parts cleaneretc.
2. Spray the adhesive surface of Rim or Decal with diluted neutral detergent using a mist sprayer, etc.
3. off rim stripe. [Plain]. ⇒ With Logo and paste them in order.
4. Remove water so that the attached Decal will not Gap.
5. Once the moisture is gone and the adhesive surface is acclimated to the rim, it is ready to run.
As I said above. It's not hard. So, work patiently.
How was your experience with it?
After the adhesive is firmly adhered, it adheres so well that it will not peel off even if the car is washed using a high-pressure washer, as long as the appropriate distance is kept.
The three-layered structure of the adhesive, printed, and protective surfaces makes it somewhat resistant to UV rays, weather resistance, and fading due to deterioration over time (there are limits).
There are also several color variations available to meet the demand for large-size garments, as well as a color custom order plan (additional gold required) that allows you to create your own original off rim stripe.
[Included Parts:were they on?
Off rim stripe for pasting+Instruction Manual for pasting is included.
First-time users should read the Instruction Manual carefully before working on this project.
[Was there anything that disappointed you?
None
Although there are many similar products that are less expensive than this product, there are few products that are simple in design, sturdy, and weather resistant that are Rival.
Other items that would be helpful
Point and hang of installation
Above. [Was it difficult to install? If you practice the method of spraying a diluted neutral detergent and applying it as described in the section "1.", it will take time until the moisture is gone, and if you accidentally touch it during that time, Decal will easily Gap.
If you want to make short work of it, please decide on the inside or outside of the rim and paste it directly on the rim.
Some car models do not have a flat rim side, so sometimes it can be applied beautifully by applying heat with a dryer (be careful how much heat is applied so that the decal does not stretch too much).
[Availability and clarity of the Instruction Manual
In addition to the included Instruction Manual, MDF's Home page includes images and videos.
If you are not confident after reading the Instruction Manual, please visit the Home page.
[Notes]
As long as the basics of Decal pasting are followed, there are no particular difficulties.
As mentioned above, degrease the Rim thoroughly before working on it. Touching the adhesive surface with dirty hands will reduce the adhesive performance, so wash your hands thoroughly before working on it.
[ITEMS TO BUY TOGETHER
Nothing in particular. If you do not have Parts cleaner, it would be useful to purchase it at the same time.
The rest you will have to overcome with spirit, guts, love, courage, and friendship.
[Opinions and requests to Manufacturer
If the price is just a little lower, it can be easily used in more vehicles, so please help us out.
View detail
If you put it on the front wheel, you want to put it on the rear wheel too.
[How is it used?
I built a Wheel for SEROW225WE for street riding, but it is in a somewhat disappointing condition for all the trouble I went through because I built a scratchy Rim on a used Spoke from Stock.
After assembling IRC's GP-210, I put on the MDF off rim stripe 15mm that I had ordered from Webike.
The harmony of the front and rear Wheels and the body of the car looks very good.
Was the one you received as per Image?
I have been using MDFGraphic's Logo since it was the old Type, so the product was just like Image.
Was the installation difficult?
The process is tedious but not difficult and requires patience.
Refer to MDF's website.
1. Degrease the area where the rim is attached firmly with Parts cleaneretc.
2. Spray the adhesive surface of Rim or Decal with diluted neutral detergent using a mist sprayer, etc.
3. off rim stripe. [Plain]. ⇒ With Logo and paste them in order.
4. Remove water so that the attached Decal will not Gap.
5. Once the moisture is gone and the adhesive surface is acclimated to the rim, the rim is ready to run.
As I said above. It's not hard. So, work patiently.
How was your experience with it?
After the adhesive is firmly adhered, it adheres so well that it will not peel off even if the car is washed using a high-pressure washer, as long as the appropriate distance is kept.
The three-layered structure of the adhesive, printed, and protective surfaces makes it somewhat resistant to UV rays, weather resistance, and fading due to deterioration over time (there are limits).
There are also several color variations available to meet the demand for large-size garments, as well as a color custom order plan (additional gold required) that allows you to create your own original off rim stripe.
[Included Parts:were they on?
Off rim stripe for pasting+Instruction Manual for pasting is included.
First-time users should read the Instruction Manual carefully before working on this project.
[Was there anything that disappointed you?
None
Although there are many similar products that are less expensive than this product, there are few products that are simple in design, sturdy, and weather resistant that are Rival.
Other items that would be helpful
Point and hang of installation
Above. [Was it difficult to install? If you practice the method of spraying a diluted neutral detergent and applying it as described in the section "1.", it will take time until the moisture is gone, and if you accidentally touch it during that time, Decal will easily Gap.
If you want to make short work of it, please decide on the inside or outside of the rim and paste it directly on the rim.
Some car models do not have a flat rim side, so sometimes it can be applied beautifully by applying heat with a dryer (be careful how much heat is applied so that the decal does not stretch too much).
[Availability and clarity of the Instruction Manual
In addition to the included Instruction Manual, MDF's Home page includes images and videos.
If you are not confident after reading the Instruction Manual, please visit the Home page.
[Notes]
As long as the basics of Decal pasting are followed, there are no particular difficulties.
As mentioned above, degrease the Rim thoroughly before working on it. Touching the adhesive surface with dirty hands will reduce the adhesive performance, so wash your hands thoroughly before working on it.
[ITEMS TO BUY TOGETHER
Nothing in particular. If you do not have Parts cleaner, it would be useful to purchase it at the same time.
The rest you will have to overcome with spirit, guts, love, courage, and friendship.
[Opinions and requests to Manufacturer
If the price is just a little lower, it can be easily used in more vehicles, so please help us out.
View detail