Reviews
DL1000 V-STROM250SX exclusive DAYTONA Hazard kit installed
I was looking for a Hazard switch for my DL1000 V-STROM250SX, and when DAYTONA came out with a switch kit for the 250SX, I immediately went to Webike and bought it. As expected of a dedicated kit, there is no extra wiring, no cutting or pasting of wiring, and I was able to install it without worry. Now I can use the hazard lamp on the highway with no worries! Personally, I believe that motorcycles are safer when they are well lit and stand out. View detail
Exhaust pressure adjustment
cbr250rr mc51 AKRAPOVICExhaust System
cbr250r mc41 WR'sExhaust System
mounted on
AKRAPOVIC can also ensure exhaust pressure, and the volume is lowered just right.
WR's are too subtle with too much exhaust pressure. Volume goes down.
Glass Wool burns quickly, so it is a recommendation to wrap Stain Wool on top of the purchased condition.
Since the exclusive for RepairGlass Wool is expensive at 1,000 yen, commercially available for RepairGlass Wool with Stainless needle Gold is sufficient.
By the way, if you open your fingernail so much that it is too hard to insert it, if you open the Axel all the way, you can….
View detail
Fits: HONDA DAX125, HONDA MONKEY125, HONDA CT125CT110 HUNTER CUB
Parenthesis OK
I think Parenthesis looks good. It is easy to install, too. The double-sided tape is visible from the outside, and it bothers me. I didn't notice it at first and ended up using a different double-sided tape to reattach it. Other than that, I have no complaints. View detail
The design and shape are good, but the gap for the tank pad is unavoidable.
The design and shape are good, but the gap for the tank pad is unavoidable. Although I purchased the product with an understanding of this gap, it bothers me a little. View detail
Fits: KAWASAKI ZZR1400, KAWASAKI ZX-14R
Well-designed Rear suspension will be protected from dirt.
It seems to protect Rear suspension from dirt with good design.
Because of the tie band fixation, some adjustment may be possible when wearing.
View detail
Fits: KAWASAKI Z1 (900SUPER4), KAWASAKI Z2 (750RS/Z750FOUR), KAWASAKI Z750FX, KAWASAKI Z900 (KZ900), KAWASAKI Z1-R/Z1-RII, KAWASAKI Z1000, KAWASAKI Z1000 MkII
Oil leak in the Tachometer port of the MKII.
I purchased this oil seal because I was experiencing oil leakage from the Tachometer port on my Z1000MKII. I have had the motorcycle for 5 years and the shop had replaced the oil seal with the same product made by PMC before I bought the bike. I wish I could have purchased those parts and repaired it at a lower price. I wish We-Big would sell repair parts for ORing and Oil seal. 。 I would like to buy OEM Parts next time to see if the ORing and Oil seal from KawasakiOEM Parts will work. View detail
To reduce blind spots.
Mirror now has a wider viewing area. As others have said, it reduces blind spots and the probability of accidents.
Is the effect of hydrophilic Option subtle? Hmmm...
I wish the Gold amount was a little cheaper since it is sold with just the mirror surface...
View detail
License Plate Base
License Plate was installed to prevent bending and staining.
The size is exactly the same as the License Plate, so it fits nicely.
I would have liked it to be a little lighter in weight.
View detail
Easy to install and good to see.
It is a simple device and looks good. The bonding strength was increased by using double-sided tape to add strength. View detail
Conti II type can be NORMAL.
The OEMHandlebar is so large that if it is replaced with a narrower one, the OEM will have a little extra space.
However, it could be left as OEM, but it interfered with the RadiatorRight Side surface.
It is a product that is better to have than not to have.
View detail
Finally, it feels right.
I made a mistake in selecting the parts, and this time I finally settled on 36 pies.
No, no, no, I bought three different kinds.
The price is right there, so it's been a needlessly painful expense.
The item is fine.
View detail
Fits: Others Compatible with CPB-1VShield, Others Glamster
U-LOOK Blaze MirrorAnti-FogSeat
[Color] As a Smoke Mirror shield user, the ability to convert the OEM Clear shield to Mirror will help prevent the Mirror from peeling off due to cost savings or pebbles, etc.!
No distortion and the view is easy to see in Mirror.
View detail
Sharp Reflector
The ReflectorSticker in the Included Parts:of the AELLAFender Eliminator Kit was not good, so I was looking up Reflector on the website and found this product.
I liked the casual design under the License Plate.
View detail
Fits: DUCATI PanigaleV4R, DUCATI PanigaleV2, DUCATI PanigaleV4, DUCATI StreetFighterV2, DUCATI StreetFighterV4
Compatible with DucatiPerformance sequential blinker
This is the parts to change when using DucatiPerformance's Blinker with AELLA's Fender Eliminator Kit.
BlinkerQuantity:Pair (for Left and Right) The long hole for adjustment can be set to the Largeest value, but the image is still used for the License PlateQuantity.:Pair (for Left and Right) The Blinker is just visible from the
View detail
Pillion Bar installed (XJR400R.99)
There is some shaving of the OEMFrame, but it was not that difficult to do. The installation method was also easy to understand if you read the instruction manual that came with the product. It took about one hour because I was not familiar with the shaving process. View detail
Fits: KAWASAKI Ninja H2 SX, KAWASAKI Ninja H2 SX SE
Speedra Carbon Tail Light Cover
The OEM ABSTail Lamp Cover is cheap, so we changed it to …Speedra's Carbon Tail Light Cover!
The texture will be much better.
View detail
Fits: HONDA PCX150, HONDA PCX
Windproofing, though.
As far as I have been able to find out, I think this item is the LARGEST as a windshield. (At the time of purchase)
I think the windproof effect is solid in the Large size range.
However, in the summer, when parked in the sun, the light was concentrated on the Screen and the inside of the Screen melted.
It is possible to countermeasure this problem by placing Towel or other material between the two, but be careful, as the entire Towel may burn if it is not properly placed.
View detail
Fits: YAMAHA SR400, YAMAHA SR500, YAMAHA SR500, YAMAHA SR400
Sounds great but loud decel popping
I think this exhaust looks and sounds great, but there is loud popping when shifting gears and decelerating. Any advice on how to fix this? View detail
Fits: SUZUKI GSX1300R GSX1300R HAYABUSA(GSX1300R HAYABUSA)
Tank Cover (GSX1300R HAYABUSAI type) Twill Weave Carbon
The product is aesthetically pleasing as a twill weave carbon and is well finished. The area of the cover is larger than that of a general stick-on cover, and the appearance of the custom parts is eye-catching, and the practicality of the cover is also reassuring, as it frees the user from the worry of damaging the tank with Belt Bracket etc. On the other hand
Urethane for surface protection [Color] The drawback is that Clear painting must be done by itself. A small amount of liquid Sauce still occurred.
View detail
Fits: KAWASAKI Ninja ZX-25R SE KRT Edition, KAWASAKI Ninja ZX-25R SE, KAWASAKI Ninja ZX-25R, HONDA CBR250RR, YAMAHA YZF-R25
Brake's Stress is reduced.
This is a change from OEM horizontal placement 11mm to 5/8Radial master.
Because it seemed to interfere with the Switch box, the Lever was changed to Eukanaya's (NI002-049),
Nisshin's Tank Bracket (49151) for Separate Handlebars is installed.
As for the banjo fitting, a stainless steel mesh hose (AC Performance line) compatible with the car model was originally installed, but it interfered with the switch wiring, so an L-shaped adapter was used to make an escape.
My impression after installation is that the absolute braking force has not changed, but the controllability has improved.
Specifically, it is an Image with interpolated increments of braking force according to the strength of the grip.
The beginning of the grip is especially noticeable. With the horizontal 11mm pad, the rise in braking force is abrupt, but with the vertical pad, there is a sense of being able to adjust the strength of the pad. The same is true near the end of the grip, making it easier to generate strong braking force without locking.
Probably because the lever ratio and diameter are designed to match the weight of a horizontally mounted 11mm lever, it will not be that uncomfortable (too effective or too ineffective) to replace it. If you want a lighter grip or more strokes, you may want to consider a 14mm or 15mm model such as the F Land-.
In general, I can recommend it, but since it is Large strange to do banjo fitting by yourself, it is safer to ask a supply store with a Pit.
View detail