Reviews
Fits: DUCATI SCRAMBLER(800), HONDA CB1000R, HONDA CB1100, HONDA CB1100EX, HONDA CB1100RS, HONDA CB125R, HONDA CB1300F, HONDA CB150R, HONDA CB250R, HONDA CB400SB, HONDA CB400SS, HONDA CB750, HONDA CRF1000L Africa Twin, HONDA CRF250L, HONDA CRF250RALLY, HONDA CTX700, HONDA DN-01, HONDA GB250, HONDA GROM, HONDA GROM
This is so convenient!
I was worried about installing a TMAX because it does not have a bar handle, but this is perfect. The combination uses a Rek Mount and Quad lock. View detail
Excellent combination with Quad locks.
I use it in combination with Quadlock's Ball type. It is a perfect match. The screw part is a bit large and looks a bit tacky, but it will be hidden when the phone is attached, so I think it's fine. View detail
Fits: DUCATI SCRAMBLER(800), HONDA CB1000R, HONDA CB1100, HONDA CB1100EX, HONDA CB1100RS, HONDA CB125R, HONDA CB1300F, HONDA CB150R, HONDA CB250R, HONDA CB400SB, HONDA CB400SS, HONDA CB750, HONDA CRF1000L Africa Twin, HONDA CRF250L, HONDA CRF250RALLY, HONDA CTX700, HONDA DN-01, HONDA GB250, HONDA GROM, HONDA GROM
Also applied to X-ADV.
I could not confirm the compatibility of the X-ADV RC95, so I bought it with no luck, but it arrived with no problems at all.
There is very little vibration.
View detail
Fits: DUCATI SCRAMBLER(800), HONDA CB1000R, HONDA CB1100, HONDA CB1100EX, HONDA CB1100RS, HONDA CB125R, HONDA CB1300F, HONDA CB150R, HONDA CB250R, HONDA CB400SB, HONDA CB400SS, HONDA CB750, HONDA CRF1000L Africa Twin, HONDA CRF250L, HONDA CRF250RALLY, HONDA CTX700, HONDA DN-01, HONDA GB250, HONDA GROM, HONDA GROM
Mount with SS
Excellent functionality for use with SS, the detail workmanship is crude, but that's just because it's a foreign product. View detail
Mounted on Motorcycle Handlebar Brace
I run with my cell phone attached to my Motorcycle.
I usually leave it on my Motorcycle.
It is quite resistant to rain and can be used for a long time.
View detail
A must for RAM Mount installation
The quality seems to be not so good since BALI is still present on the ball portion, but the installation itself was not a problem.
I have it mounted on a ZETA Handlebar and there is no wobble at all.
View detail
Securely attach your phone.
At first I was worried that my phone would fall off, but the tether makes me feel safe.
There are rumors that the Camera will break if it is an iPhone, so I am using my old iPhone 7 Plus with it attached.
View detail
I'm happy with the sufficient length.
I installed it on my WR250X
I have also installed a ZETA Handlebar and was able to install it without any problems.
Removing, attaching, and changing angles is very easy, as all you have to do is turn the lever.
View detail
firmly fixed
It can be fixed in a tight and secure manner. However, there is no Bandetc., so be careful not to drop it.
A mount to fix to the stem hole is required separately.
View detail
sufficient for one's needs
Purchased to install ActionCamera avoiding the front cowl of the Motorcycle. The angle is more flexible and convenient. View detail
Fits: DUCATI SCRAMBLER(800), HONDA CB1000R, HONDA CB1100, HONDA CB1100EX, HONDA CB1100RS, HONDA CB125R, HONDA CB1300F, HONDA CB150R, HONDA CB250R, HONDA CB400SB, HONDA CB400SS, HONDA CB750, HONDA CRF1000L Africa Twin, HONDA CRF250L, HONDA CRF250RALLY, HONDA CTX700, HONDA DN-01, HONDA GB250, HONDA GROM, HONDA GROM
Easy installation on zx10r
Installed on Motorcycle as I am addicted to my phone.
RAM Mount's are easy to install.
Simply remove and replace the Bolt on the Stem.
It is equipped with a locking agent, so it takes a lot of strength.
View detail
Wish I had switched to this earlier.
It is TORQUE 5G and it is just the right size. Just by clamping it, even if it is a little rickety, it doesn't gap at all. It is as expected from Ram Mount. View detail
Universality
We selected this product to install Tire's wireless Air gauge Monitor.
The 1/4-20UNC screw for general camera use can be used.
There is no retightening component, so the angle must be adjusted after the Camera or other device is firmly screwed in.
View detail
Select Length
We selected this product to install Tire's wireless Air gauge Monitor.
The large handlebar may be difficult to tighten depending on the installation location and angle.
I chose the standard size without thinking, but the short size seemed to fit better.
You may choose Standard or Short by taking measurements of the mounting location.
View detail
racing (of an engine)
To install Tire's wireless Air gauge Monitor.
We chose this product, which uses Stem holes, because we did not want to increase the number of conspicuous Mounts.
I could not get the installation to work and when I repeated Cut, it went blank.
Instead of following the instruction manual, once the cut is made, the Stem hole should be filled to the Limit.
Tightening Bolt and expanding Body may work.
It will not come off, so it will be used as is.
View detail
Is there a mistake?
I couldn't believe my eyes at the difference between the statement and the merchandise.
What's his mistake?" I feel a little lost.
View detail
Excellent in both fixation and usability
At first glance, the 4-point rubber arm looks poor, but it fixes quite Firmly. In the past, when I was using a mount from XYNA, my phone flew off with a shock when I went over a bump, which was a tragic experience, but it has never happened after using this product. The other parts can be easily attached and removed without tools, so it is very convenient. View detail
It is probably the easiest way to attach and detach the phone.
I think this Smartphone Holder is the easiest and most stable way to put on and take off the Smartphone, and is suitable for those who frequently put on and take off their Smartphone while touring or taking a break. I just wish the price was a little lower! View detail
There was one for a Large-ish phone!
It has been about 18 months since I purchased Ram MountBody in September 2020. During that time, I used it about 1-3 times per month when Touring, and before I knew it, theRubber was shredded.
I had a feeling that it would break off at some point, since I had been stretching the Rubber as hard as I could to fit it into the largest one I could mount (iPhoneXS Max).
I had no choice but to replace only Rubber, so I pulled up the Ram Mount product list...?
Fa Brett." ? What does that mean? → I heard this is what they call the middle Size between a smart phone and a Ta Brett (I've never heard of it before). If my sma... Fa Brett." ？？
So I bought this Size to try it out.
As it turned out, it fit perfectly!
I wonder if this Size has been around for a while? I'm glad I found it.
View detail
Mobile Holder
I bought this for navigation on my phone, but I read on the Net that the iPhone's Camera function can break down if it's fixed too tightly…
Not sure whether to use it or not.
View detail