Reviews
Shipping is good.
It is only now possible to attach an external DialWire lock to the Handlebar.
I think what you want to do is reasonable.
However, we still would like to see some improvements due to the use of existing locks.
1.Dial is Smaller
I don't want to touch it in the winter or anything.
2.Wire is too long.
Handlebar position could be half as short as it is now.
3.Lock position
Not the other way around, as they tend to pop up on the Grip side and interfere with each other.
I dare to put it on the other way around.
It would be nice if this area could be improved, but it is regrettable.
View detail
Useful if you have it ^^.
[How is it used?
When you stop at Convenience or some other place where you stop for a bit.
Was the one you received as per Image?
Large Image Street
How was your experience with it?
It did not go into the CYGNUS Hell Lock pin as is.
[Points to note]
The pin holes are unexpectedly small, so some modifications may be necessary depending on the vehicle.
How did it compare to other products?
No comparison
Other items that would be helpful
As a side note, the included Carabiner is too small.
The 100 yen shop items of today are of higher quality.
View detail
Cannot be installed with Carrier
Ease of use of Helmet lock is normal
Installation was easy with tools.
Note that if a KIJIMA Rear Carrier is attached, it will overlap the Pipe and will not be usable.
It's about making sure you use other locks.
View detail
Installation of helmet holder on XSR125
We install most of Motorcycle's helmet holders on each vehicle we deliver.
As usual, it is useful for Helmet lock when parking the bike.
It is a vehicle specific product, but I had to shave it down a little to install it because it hits the side cowl a little.
View detail
![[K・TOUR] Helmet Holder](https://img.webike-cdn.net/catalogue/images/108481/80-564-90250_1_TS.jpg)
Place Helmet on Top Bridge and lock it.
The standard helmet holder of ZX14R was placed on the Left Tandem Footpeg, but when the exhaust system was replaced, the Tandem Footpeg was removed and the helmet came in contact with the silencer. The silencer is no longer used since it is placed on the Top Bridge because the rubber may melt when the silencer is hot.
I had been leaving it unlocked, but since I bought a new helmet, I was concerned about theft and decided to purchase a retrofit helmet holder.
It was attached to the Multi Bar with Smartphone Holder so that the Shield could be opened for easy key operation.
It lacks a SMART appearance, but it has achieved its purpose for now, so I will use it for the time being.
I might remove it if I can't stand it anymore (laughs).
View detail
To relieve the anxiety of a short break.
I bought this product because the CBR1000RR SP sc77 does not have a Helmet holder in OEM and there is no Screw hole to install a Type product that mounts on the Frame.
I used to hook it up to Mirror when I took a break at a touring destination, but it was half the fun with the fear of theft.
After installing this one, I was able to leave the vehicle body with some degree of peace of mind, so I think it is actually quite cost-effective as a cost-effective solution.
Installation is not particularly difficult as long as the size of the car body is carefully checked.
If I had one request, I would have liked the key to be 4-digit instead of 3-digit. I thought that if you leave for a long time for meals, etc., it might try all patterns and be unlocked.
View detail
Very good product
I like it because it is Design cleaner than other companies' products.
Installation was easy and the feel is very good.
Spare key is also included.
The bolt is also a stainless steel bolt.
View detail
Fits: DUCATI MONSTER1100/S, DUCATI MONSTER796, DUCATI MONSTER696, DUCATI MONSTER796, DUCATI MONSTER696
Might be easier to use.
It can be said that it is easy to hook because of its large opening, but it is difficult to remove it without using both hands.
It happens to be the place where the Battery Charging Cable is out, so you should think carefully before attaching it.
View detail
Fits: Others , HONDA MONKEY125ThailandMODEL, HONDA MONKEY125, HONDA PCX160, SUZUKI GN125-2F, YAMAHA YB125SP, YAMAHA XTZ125, KAWASAKI KLX125, KAWASAKI D-TRACKER125, KAWASAKI Z125PRO, KAWASAKI KSR110PRO, KAWASAKI KSR110, YAMAHA XT250SEROW, HONDA CRF250L, HONDA CRF250RALLY, HONDA Dunk, HONDA MAGNA50, HONDA XR100 Motard, HONDA XR50 Motard, HONDA APE100 TypeD
Nice little addition to my Monkey 125
I live in an urban area and wanted to keep my helmet locked with my bike although theft is not too common here. The stock helmet lock is located at an awkward spot that's too low and inconvenient for me - I had to try out this one. Installation is easy, product works as promised. View detail
Fits: Others , YAMAHA BWS 50, YAMAHA BWS125, YAMAHA MAJESTYS, HONDA ZOOMERX, HONDA PCX125, HONDA PCX125 E:HEV, HONDA PCX125 Hybrid, HONDA PCX150, HONDA PCX160, HONDA CROSSCUB110, HONDA glom, HONDA MONKEY125, HONDA CB125R, HONDA CBR125R, HONDA CB250R, KAWASAKI Z125-PRO, HONDA DAX125, HONDA CT125CT110 HUNTER CUB, HONDA CL250
For CL250
Side Back on CL250
Because it is installed
Master Cylinder in Kochira
Type's installation on the
Helmet holder.
View detail
Fits: BMW R1200GS, BMW R1200GSAdventure, BMW R1250GS, BMW R1250GSAdventure
No need to worry about food while touring.
I used to hang my helmet on Mirror when I took a break during touring. I was worried that it might be stolen or fall off, but now I feel safe! However, I am worried about rust because the material is steel. It is easy to install and just fits. View detail
Fits: HONDA PCX125, HONDA PCX125 Hybrid, HONDA PCX150, HONDA PCX160, HONDA CB125R, HONDA CBR125R, HONDA CB250R, KAWASAKI Z125-PRO, HONDA PCX125 E:HEV, Others , YAMAHA BWS 50, YAMAHA BWS125, YAMAHA MAJESTYS, HONDA ZOOMERX, HONDA MONKEY125, HONDA glom, HONDA CROSSCUB110, HONDA DAX125, HONDA CT125CT110 HUNTER CUB, HONDA CL250
It does not mount well.
The genuine brake lever and the product are not fastened well, resulting in a part left on the handlebar. To mount the helmet, the direction was reversed. View detail
It would be more convenient to have
There is one on the Body, but I bought it because it is inconvenient to use it without removing the Seat, and also because it is essential when I tandem the body.
I am satisfied, including the price.
View detail
That's DAYTONA!
I guess it means that DAYTONA is the distributor of MAGGI, but the same size on Amazon is DAYTONA and Webike is MAGGI, then I should buy from Webike. So, I'll buy it from Webike.
I thought it was DAYTONA. Absolutely not." I was not saying that I wanted to buy DAYTONA products, but I wanted to avoid them because I have been making a lot of mistakes buying DAYTONA products recently, emotionally.
View detail
My mistake.
I had posted before that it could not be installed without modification, but this is because I installed the bracket backwards and forwards, so there is no problem at all except that it is difficult to attach the mounting screws. It is a good product. View detail
Processing required
The guide on the body side of the mounting bracket was not attached as it was because the body attachment part of the mounting bracket and the guide on the body side were in contact with each other. The screw fastener of the mounting bracket also interfered with the box part of the air filter when the length of the wrench was too long, so I wondered whether I should cut the wrench or not, but I loosened the box side and shifted it to close. View detail
Good feeling on Design
I was feeling uncomfortable with the lock on the SIDE of the helmet, so I bought it because I thought it was an ideal place to lock the helmet. The lock looks great on the helmet, but since I have a box on my V-SX Cali, I can't hang it on the DRing because there is not enough space to operate it, so I hang it on the band. View detail
Installed on current YZF-R25
Adding a Helmet lock would add another 1 pc of keys, so I added a Tanax Wire lock, which I have been curious about for a while.
The brake lever side is slightly adjusted and lowered, but even when fully locked, it could be installed without interfering with the LimitCowl.
I chose the Coil type, but it was harder to stretch than I expected, so I thought I should have chosen the Straight Type.
View detail
It's convenient
Installation is as simple as replacing the OEMBolt with the supplied Bolt, Washer, and Collar.
If a Smartphone Holder etc. is attached near the with Handle, the wire length may not be sufficient, so this should be considered.
View detail
Helmet is now easier to lock.
I was having a hard time using the helmet holder that I moved when I replaced the rear suspension made by Y's Gear, and when I locked the helmet, it was close to the engine, so I had to be careful about the mounting angle, etc. I saw this product on SNS and thought it looked good, so I bought it.
Tandem Footpeg and Bracket are attached by co-tightening, but our car is equipped with SSB GymkhanaBumper and Quantity:Since the Slider in the set is attached in place of the Tandem Footpeg, the Spacer included in the product was not used.
I was able to install it without hitting the frame.
The OEM lock part was available as is, so the part used in this product was Bracket Only, but I am still satisfied with the ease of locking.
View detail