Reviews
Is this what it looks like?
I'd like you to release the Black Anodized in Aluminum.
Also, Quantity:Pair (for Left and Right) I'd like to see the total weight published.
Previously. It's about making the bike lighter and losing weight yourself! And there was an article about...
View detail
If you just want to use it, this will do the trick!
You may want to relocate Mirror quite a bit and use it, right?
With OEMs, it's often attached to the switch box or rebar clamp, and this is handy when you want to get it out of the way.
This type of product is available at PinDrill, but if you just want to relocate it, this is good enough for you.
View detail
Repeat
I had the same one on, but I had to repurchase and reinstall it to change the angle.
However, the bolt is too thin and the torque-tightening torque is not enough, and when the weight exceeds 100kg, the Mirror turns around due to wind pressure.
It's a shame that it's so weak.
I drilled the hole to the Handlebar and screwed the Bolt in.
Last time I was cutting from the top and there is a hole in the handlebar, so this time I cut from the bottom.
If you do this, you won't be able to fine-tune it and you won't be able to get it back, so make sure it's in the Mirror adjustment range and drill the holes.
I... No one does. (+o+)
View detail
To avoid the Master CylinderTank
When I bought a Tanax Napole OnMirror and tried to install it on the GSX-S1000F, it interfered with the Master CylinderTank of Brake and I couldn't install it, so I bought this Adapter and added the height to it.
Although there is nothing to write home about in terms of performance, I think Tanax is a reliable manufacturer that you can buy from in the sense that they have such parts that can be fine-tuned.
View detail
A must-have for Yamaha
Most mirrors on the market are not Opposite Thread Screw.
But Yamaha has Opposite Thread Screw, why? Aside from the reason for this, I'd like to see a commonality in these areas.
Now, this Adapter is a necessity for the Yamaha cars. It may be a little bit high on the Mirror, but that's okay.
View detail
It might not look good on the OEM Mirror, which has a thicker root in recent years.
I bought this product, which is the only corrective part, because the angle of the Mirror Holder became bad due to the Custom, and I couldn't see the rearward vision in the adjustment range of the Mirror.
I used to use the OEM Mirror for the ZRX1200R, but the thicker base made this Adapter look less balanced.
Since the Mirror was replaced, we rejected it this time.
It does not correspond to Japanese Vehicle Inspection.
This may be the only HURRICANE Parts for Mirror, but it was a product not carried by the local Naps.
View detail
There's no problem, sir.
The Plating has a nice texture and the installation was completed comfortably.
It was a perfect match for Mirror.
Thank you for taking it for granted!
View detail
Only the surface finish is disappointing
Purchased in place of the too expensive brembo OEM Mirror Holder
It would be helpful if the colors were displayed more clearly
Personally, I'd rather have all the colors Shot blast applied in advance to give it a cast-iron look I don't think it's strange to match with Master Cylinder, but …
Basically, I think Design is a finish that only fits the slippery shaving MASTER!
View detail
Mount 8mm Mirror to 10mm Handlebar
[Was there anything that disappointed you? Because the Screw of Mirror is too long or the Adapter has bottomed out, I put a bolt on it I did
Do you have any wishes or improvements you would like to make for the Manufacturer? If the female thread on the Mirror side is longer, BEST
[Do you have any products to compare it to? None
Frequently Asked Items
What made you decide to buy? I don't know if there is an 8mm Mirror set screw or a 10?Handlebar set screw adapter No
How was your experience with it? perfectly (suited)
Was the installation difficult? None
【Please tell me the installation point and hang】 None
[Was the Instruction Manual easy to understand? None
[Included Parts:were they on? Warranty Is it really necessary?
[Others] So it's currently out of stock
View detail
Reactly for Low typeMirror visibility
Used for HUNTER/Low AndNarrowMirror
I liked the design, but the Mirror is so low that you have to look into it to see what's behind you I was wondering if I should replace the Mirror as I didn't have one, and then I found this product
The result is very good visibility
It was easy to install with good accuracy and I recommend it
View detail
Mirror View Widening to Large
A little more Mirror on the outside would have made it easier to check the rear, but it helps in those situations
Material:The influence on the Handling is small because it is Aluminum and Large and light
You can also choose two different mounting heights for the Mirror, so fine adjustment of its position is also possible
But the Bolt that comes with it is a bit cheesy
A low head Bolt would have looked much better
View detail
Repeat
I bought it again because I bought it before and it was good The installation is solid, so I bought a bracket for different purposes on top of this one and the Camera I put it on and load my phone on it The other Holders feel too delicate to use anymore View detail
tightly packed
It is good if it becomes a little more Smallish, but because it can be fixed to Handlebar firmly I am very happy with it and it is stable even with a large piece of hardware installed View detail
Using it differently than it should be used
I used it to extend the rear suspension attachment point of MONKEY If you put the exhaust bracket in between the bolts, you can only tighten up one or two suspension bolts It is not
Both Sides female screws for extension to Exhaust Bracket installation You can buy the attachment but it costs about 1,000 yen
Pitch of MONKEY's suspension bolts is 1.25
Attachment is p1.25 when the Screw is cut off by Penetrating it I think, but home center usually sells only 1.5-pitch bolts for M10s I don't have one, so I have to buy the Bolt on the other side at the Screw store
This will allow you to use it directly on the suspension mounting bolts, and you can use it to fix the suspension in place of the original The OEM Cap Nut can be used as is (Depending on the thickness of the exhaust bracket, it may be possible to tighten the cap nut as is (It may be Penetrating, so adjust with Washeretc
View detail
Cheap with Chrome plating
Replaced with a Plating Mirror and put it in the same Chrome plating Adapter Changed, there is no plating failure etc. which is common in cheap ones, and pre-treatment of plating The post-processing is well done, no unevenness, no swelling, no fogging, and the forging process is well done It is a good buy at this price I believe that a motorcycle that is well cared for can keep its quality for a long time It is very comfortable to use with a domestic plating mirror The shortness of the mirror and the length difference between the other side of the mirror without an adapter is very noticeable It fits in the Small limit View detail
Rearward vision is now better
The Z900RSCafe is supposed to be a Short mirror than the regular Z900RS Quantity:Pair (for Left and Right) away
Therefore, rearward checks while driving are not required for Quantity:Pair (for Left and Right) I had to shake my head quite a bit at
When I was getting a reasonable amount of Speed, I couldn't get a glimpse of the eye feed and it was Stress
That's why the old-time flyers used to use short mirrors, and I've been using short mirrors myself mirror
But this time it's too short, so you can see your shoulders in the background needed
At first, I held back on the quackery, but the urge to get the Mirror out three more inches made me buy this one I did
Rearward vision is so much better and the visibility is a perfect balance
At first I thought it would be an inexpensive one
I chose this one by AluminumMachining because it is still a very visible place The quality is high and I am satisfied with it
However, this product is more expensive than MirrorBody, so the quantity:Pair (for Left and Right) It would be great if you could make it about $3,000 in
It's important to note that the Body is highly textured, so
Bolt is also included in Included Parts:I wanted to use the Bolt for something more substantial It was a bit of a struggle, but
What I found out at the time of the temporary clamping is that the Bolt for Mirror is a normal way to get Pitch It's not like Bolt's Pitch
The Bolt that I bought cannot use the Bolt that I bought with great effort, and it became a Waste use After all, I used the included Bolt
View detail
That's Tanax
I figured if I was going to buy one, it would be Tanax!
Left SideMirror inevitably interfered with the Left SideMirror, so I installed it
It is thick and of good quality
View detail
Nice Screw Adapter
This TANAX Left-Handed Screw Adapter is very useful. It allows me to lift up the mirror a little bit, and to allow me to install a mount between the mirror and the screw adapter. View detail
If it becomes a reference at the time of Dorareko installation to CB 400sb
Purchase for adjusting the height when attaching the Dorareko to the Mirror hole.
Regardless of whether or not, the Bracket of Cowl mirror is reflected, so it is better to put the Dorareko in a different place.
View detail
Some people need necessities
Unnecessary for people who do not have trouble with OEMMirror
For those who want to replace Mirror with purpose
We bought to attach the mirror folding Mirror to SEROW
Since I wanted to use Mirror as it is with Honda SL 230, my previous car contributed to Reduction in cost
Because Merit and Demerit are products that differ considerably among people, I want you to think well and purchase
View detail