Reviews
For use with the 3RW1 that is not the appropriate model year (but requires modification).
Compared to NORMAL, the large size of the footrest surface is obvious.
It is stable, but its thorns are sharp and long, so please use it with hardy boots that can shave off the Sole.
When used in 3RW, the Right Side must be considerably reduced to be able to be overthrown.
And even if it is installed after much effort, the rattling is so great and the return in collapsible mode is so weak that further modification is required.
If you are concerned about the details or if the modification is troublesome, you can install the expensive Bolt On. "ARE" is probably a good idea
View detail
Conforms to ST1000 Regulation
I purchased the Tail Lamp to compete in the ST1000Class at the regional championships.
I purchased the DRC Tail Lamp because it meets the ST1000 Regulation.
Brightness is not a problem.
View detail
I like the color.
This is my first ReturnRider in 8 years, but I have been using DRC mono for a long time, so this is a Repeat purchase.
I love the texture and color.
However, you should be careful not to widen the claws on the bottom side, otherwise the Wound will get into the edge of the License Plate.
(I actually inserted it without expanding it, and when I removed it, it had a Wound in it…)
Currently I am using only the color Washer and Bolt because they interfere with the Fender Eliminator Kit that I installed separately.
View detail
Exhaust pipe stepping stone injury prevention
I installed this Guard as a measure to prevent mud stains and scratches from stepping stones on the exhaust pipe. I am satisfied with the workability and cost performance of the Guard.
The only complaint is that the paint color of the Guard adheres to the exhaust pipe. Although I have some dissatisfaction with the product, I am satisfied that I have achieved my goal.
View detail
Screw loosens rather quickly.
I wanted a folding Mirror for forest road touring and bought it because it was featured on DirtFreak's YouTube.
The screw that operates to fold up the Mirror started to loosen after driving 1000 km after installation, and while driving on a forest road, the screw came off and the Mirror slipped off. Fortunately, I was able to pick up the Mirror, and after returning home, I bought a Gold washer, a hexagonal Screw&Nut, and a spring washer at Home center and tightened them.
The attached washer and Hexagon Nut alone will loosen, so it would be safer to put a spring washer between them.
Mirror itself is easy to read for the price and the texture is up to the task.
View detail
Fits: HONDA CRF300L, HONDA CRF300L RALLY, HONDA CRF250L, HONDA CRF250L(S), HONDA CRF250RALLY, HONDA CRF250RALLY(S)
Heavy.
It is quite heavy. But it's solid.
It looks sturdy, but I wish it had a little more load capacity.
View detail
Fits: KAWASAKI D Tracker 125, KAWASAKI D Tracker X, KAWASAKI KLX125, KAWASAKI KLX150, KAWASAKI KLX250, KAWASAKI KSR110, KAWASAKI Ninja 250, KAWASAKI Ninja 250R, YAMAHA FZ1, YAMAHA FZ1 Feather, YAMAHA FZ6 04-17, YAMAHA FZ6-S Feather, YAMAHA FZ8, YAMAHA MT-01, YAMAHA MT-07, YAMAHA MT-09, YAMAHA TDM900, YAMAHA V-MAX 1680, YAMAHA WR250R, YAMAHA WR250X
I wish it was 10mm diameter.
Purchased to replace LED Blinker.
Maybe it's compatible with Yamaha stuff or something.
Since I could not be sure, I bought a DRC product that I could be sure of.
This product is used between two pieces, so the front and rear blinkers are interchangeable.
2Quantity:Set is required.
Since the mounting hole of this product is 8mm diameter, the Screw diameter of the Blinker to be installed is also 8mm diameter.
The 8mm blinker is used, but there are surprisingly few 8mm-diameter blinkers.
The problem is that most of the products sold at low prices are 10mm diameter and there are very few options.
View detail
You shouldn't change it with Fashion.
I found that many other people's reviews said that it was blurred, but I put it on thinking that it is an Other Brand Product, so it can't be helped if it's a little blurred,
It's so blurry!"
There are two reasons for the shake. One is that the joints are designed to stop clicks, but the play between each click is too large to stop the click properly.
Closing the screws until they stop will interfere with folding, and even if the screws are tightened just enough, they will loosen because there is no kind of lock.
Second, the joints are plastic, so they are weak to begin with. Shaking occurs.
As a countermeasure, I changed the Nut to a Self Locking Nut, and since the Bolt length was also insufficient, I changed it to an M6×25 Cap bolt.
It sticks out a bit. (See photo)
I thought this would make it a little better if I fine-tuned it.
Unless you are loading a transporter or running a closed course on your own, you probably don't need to change it.
Parts used by those who really need them.
View detail
Not required for all DRCSprocket
I got a DRC Sprocket separately and mistakenly thought this Bolt with Taper was a must and bought it. View detail
The construction is not good.
It is not well made and has a playful clatter.
The good thing is that it folds! That's all.
View detail
If you want to build a Tire with Tube, this is the one.
It is useful to pull out the Tube type Air Valve with ah-ha.
However, the Type Puller, which uses leverage, is better for use with Air Valve for Tubeless.
View detail
Preliminary.
Is it too much to ask for OEM-like ease of seeing in Foldable, which needs to be adapted to the usage situation for rearward checking and blurring? View detail
Careful work was essential for the softer TPU.
It was affixed as protection against the odd summer heat and direct sunlight.
First, I will list the items that were of interest to me in the work and that I think should be noted.
In addition, it is necessary to prepare a water spray container, a small-size film scraper, kitchen paper, and a paper windshield wiperetc.
We believe that it is better to proceed one by one without haste, except for PROs, so as not to make mistakes.
The first thing to note is that dust removal should be thorough, pointing to the included Kit for a clean finish.
Next, positioning should be done carefully and securely. If this is not done properly, the paste will not be applied properly.
Then, check to make sure there is no TPUFilm left on the release paper on the Meter side! After confirming that there is no residue of TPUFilm on the release paper, spray a large amount of water on the Meter side and the mounting surface to prevent shifting, and then gently place the TPUFilm on the Meter side and the mounting surface.
(I thought this was Large! I didn't notice and wasted the first one with the film still on the release paper...)
Finally, turn up the upper yellow release paper a little and spray it with plenty of water using Spray, then use a scraper on the upper side of the yellow release paper! and then eject the air from the top side of the yellow peeled paper in each direction.
I stuck it on anyway, thoroughly and carefully checking and not compromising.
Unlike the W, this soft TPU film is thin and stretchable, so I thought it would be as easy as the hard film for the W. However, I failed in both the display and the tachometer portion of the first sheet. (Sweat)
The second one was barely successful in attaching both, and the installation process was both a relief and a satisfying experience.
After the application, there will be some white traces until the water dries, but after it dries, the finish will be clear and beautiful.
Maybe the price and the work will protect it well from UV and WOUND.
It has been a year for the W and it still looks the same as when it was applied, so I expect it to be more durable in the future.
View detail
Fits: KAWASAKI Z900RS, KAWASAKI Z900RS CAFE
DRC MeterFilm
It was very difficult to install, I bought it for Z900RS and it goes on without any problem. View detail
Fits: KAWASAKI KDX200R (for competition), KAWASAKI KDX220R (for competition), KAWASAKI KDX250R (for competition), KAWASAKI KL250, KAWASAKI KLX250ES, KAWASAKI KLX250SR, KAWASAKI KLX300R, KAWASAKI KX250, KAWASAKI KX500, YAMAHA WR250Z, YAMAHA YZ250, KAWASAKI KDX200SR, KAWASAKI KDX220SR, KAWASAKI KDX250SR, KAWASAKI KDX200, KAWASAKI SUPER SHERPA, KAWASAKI KLX250R (for competition)
Commonly usable
SUPER SHERPA uses 13T, dropped 1T from NORMAL.
I think Circlip was harder to put on than OEMSprocket when installed.
Also, the lack of RubberDamper seems to make the noise level a little higher, but I guess all Universal Products are like that.
View detail
Off-road mirror
The NORMAL was broken during a course run, and since then it had been installed from DT230LANZA, so it was a challenge to change to another manufacturer and also to the same manufacturer.
It is good when parking the bike or driving in the forest, but it is shaky when driving.
View detail
Might not make much sense to replace from OEM.
It is good that the angle can be changed, but it does not work when it is tightened, a tool is inevitably needed.
Mirror is shaky when loose enough to move by hand.
View detail
It's the same as LCD Film on your phone, although LCD Glass is better.
[How is it used?
Just put it up, not sure yet.
Was the one you received as per Image?
Street Image
Was the installation difficult?
simple task
How was your experience with it?
Not sure yet.
[Included Parts:were they on?
Quantity:It was 1 Set of 2pcs.
[Was there anything that disappointed you?
I want to keep an eye on durability.
Other items that would be helpful
Opinions and requests to Manufacturer Please release LCD Glass as well!
View detail
Replaced due to discoloration
I replaced it because it was Brown.
The product is sensitive to ultraviolet rays and discolors, so be careful if the product is parked in a garage that is often exposed to sunlight.
View detail
Fits: YAMAHA DT200WR, YAMAHA DT230LANZA, YAMAHA TRICKER, YAMAHA TT250R, YAMAHA TT250R RAID, YAMAHA WR155R, YAMAHA XTZ125, YAMAHA XT250, YAMAHA SEROW250
TTR125LWE It's true, but...
Referring to other people's IMPRESSION
‘23I bought this for my TTR125LWE!
The product workmanship and installation itself,
It is a very good product with no problems at all!
It is not for TTR125.
it can't be helped
The width of the Brake Side from the vehicle body.
3 to 4 cm increase
Enduro, G650 XCOUNTRYetc.
We'll see if you care.
Not until I've used it.
In the absence of dedicated products,
Think of it as a Universal Product.
It's like, "Oh, well, that's okay.
View detail