Reviews
Fits: HONDA CRF250RALLY, HONDA CRF250M, HONDA CRF250L
These are good Items!
Just putting this on will give you an overall tighter look.
The color scheme is also good without being stigmatized by the OEM exterior.
M5 Hexagonal Wrench and radio pliers for mounting (Nipper) was needed and the work took 10 minutes.
The Left Side has three in-Hemp palmocks, the Right Side has two screws and Install with three in-hemp palmacks.
It is mentioned in another review that one of the Right Side locations cannot be installed, but the Rear It can be attached to the Master Cylinder of the brake.
View detail
Fits: KAWASAKI KLX250, KAWASAKI D tracker, KAWASAKI D-TRACKER-X
Cover range is good for a wide range. Installation requires some creativity.
I used to use Z-CARBON Frame guard (item number:ZC35-5115), but the cover range was too narrow, so I changed to this product.
important item
[Was there anything that disappointed you?
Right Side Cover can be fixed at 4 points by Bolt, so it can be installed firmly, but Left Side cannot be fixed firmly because only one point is Bolt fixed. I added Tie Wrap and fixed the lower part of Cover.
Do you have any wishes or improvements you would like to make for the Manufacturer?
The method of fixing Left SideCover should be more creative. And I want you to attach the protective seat to the CoverReverse side of the part that might touch the Frame.
[Do you have any products to compare it to?
Z-CARBON Frame guard (Item # ZC35-5115)
Frequently Asked Items
What made you decide to buy?
Because the coverage range is wider and the price is cheaper than Z-CARBON Frame guard (item number:ZC35-5115).
How was your experience with it?
The frame covers a wide area, so you can cover a large area of contact with off-road boots.
Was the installation difficult?
The Right Side cover is originally It is mountable to the bolt, but since my motorcycle has a modified rear master cylinder, I added an extra clearance at the contact point. I used Tie Wrap of the size that fits into the groove under the Cover and fixed it to the Frame. Now the wobbling was solved.
【Please tell me the installation point and hang】
As it is, there are several parts where the Frame and Cover come into contact with each other, so I bent the Cover slowly by hand so that it does not come into contact with the Frame, and furthermore, I put a thin Urethane sheet on the reverse side of the Cover to avoid the contact with the Frame.
[Was the Instruction Manual easy to understand?
Only a very simple Instruction Manual is included, so you'll need to be creative in your installation.
[Included Parts:were they on?
4 Bolts for the Right Side Cover, and Quantity of Bolts and Nut for the Left Side Cover:1 Set。
View detail
Fits: HONDA CRF250RALLY, HONDA CRF250M, HONDA CRF250L
Parenthesis OK
2019 MODELCRF250L
I bought it because I was concerned about the slippage in the Frame when I wore Boots
I chose this one because it looks better and cheaper than ZETA's Aluminum
Black plastic with red hard rubber inserts
The LeftParts were warped, so I used a heat gun to mold them, but even if I didn't, Tie It's not a problem because it's held down by the Wrap
Left is Tie Wrap Fixing only
The Right reuses the two Screws in the Frame where OEMGuard is stopped It also uses Tie Wrap as well as Left
The other reviewers say that they use Sub-frame's Screw, but the Screw is very easy to touch No It is said that Tie Wrap doesn't stop at 1 pc, but it is also said that Master Cylinder and If you can pass through the gap between the frames, the frame is durable enough
There is a hole in the Screw where the load is applied, so you won't have to touch it
Instruction Manual is a translation (please do not enter here, but ScrewQuantity on the Right:I have to decide where to cut the 2pc and Tie Wrap, so Instruction It takes about 5 minutes without looking at the Manual
Looks pretty parenthesis better
Large Satisfied!
View detail
more than expected
I was impressed with the texture, which is more than I imagined
All at once, Race ish
It helps just a little bit with the heat exhaustion lol
Pricey, but still a compromise as it is Carbon
View detail
Fits: HONDA CRF250RALLY, HONDA CRF250M, HONDA CRF250L
To match the color
I bought it for my partner's CRF250L
I need Frame's protector to go into the woods That's why I was looking for it
The color of the car matches the body color
ParenthesisIt came together well and they liked it
View detail
Fits: KAWASAKI KLX250, KAWASAKI D tracker, KAWASAKI D-TRACKER-X
Installation accuracy
As per the other imprints, the installation accuracy was not so good
Because the gap between the Frame and the Guard is large, put a rubber sheet in between I buried it
The Guard itself is processed by Hairline to prevent scratches from being visible
Other than the installation accuracy, I'm generally satisfied
View detail
Suzuki Carbon Frame Cover
Expecting nothing less than excellent from a Genuine Suzuki product. 100% perfect quality and fitment, the shipping was super fast too. Would recommend A+++ View detail
Fits: KAWASAKI KLX250, KAWASAKI D tracker, KAWASAKI D-TRACKER-X
He was very active recently
It's the one I installed in the shop when I bought the bike
Boots, etc. will not damage the Frame and will increase the ease of operation, but
When I took it off after 10 months, the edge of the Guard hit the Frame and the paint peeled off
I don't mind because it's out of sight, but when I recently replaced the Footpeg
This product prevents interference with the Frame, which is a unique problem
It's a true moment of success
I'm going to change the color with paint for aluminum because it doesn't match the color of the frame It is
View detail
I am satisfied
I recently installed this on my recently delivered S1000RR, a 2019 model
At first, I was worried about AlphaRACING, but I was told it didn't fit the current model, and it was also 20,000 more than SSK It was about as expensive as it gets
And I chose this one
There is a twill weave glossy, but beautiful Material:Carbon Style
It can be installed only by double-sided tape and the position of the holes are also Exactly
Considering that you buy a BMW Option, I think this price for Carbon is an excellent price for the cost It is
View detail
Fits: BMW S1000RR, BMW S1000RR, BMW S1000RR, BMW S1000RR
I don't think it's good
It took eight months to deliver one month (Lol)
The person in charge of the project was very polite and helpful, but the supplier and manufacturer's response was not I was terribly worried about the lack of/slow
I think it's pretty cheap in the Carbon cover that covers the inside of the Cowl to the Frame!
My impression of the product is that there are a lot of areas where the Carbon eye finish and Clear paint job is messy and not shiny enough There was
The position to put Double-sided Tape on, because there will be a part that floats quite a bit I had to think carefully about the
I think the heat from the Frame is not transferred easily thanks to the floating structure (Lol)
It was able to avoid the welding part of the frame, but it was too much avoidance It didn't fit in the gap between the two, so I shaved it off and put it in
It did not come with any instructions or double-sided tape
View detail
It won't come with the KDX200SR!
I bought it with the KDX200SR (89-93), but I opened it and tried fitting it How do you fit it on at all? I'm not going to fit, as much as I'd like to!
The screw holes are also open, but there are no screw holes in the KDX200SR at all I'm not Fitting!
I'm not just disappointed, I'm stunned, I can't even say things!
I feel like I've been lumped in with only the gold, which is a good thing for non-returnable items
If the Package says KDX200SR (89-93), you'd normally trust it too (89-93) (Anger)
View detail
Fits: HONDA CRF250RALLY, HONDA CRF250M, HONDA CRF250L
So-so
It was more Reasonable than ZETAFrame guard, and it was Colorful I chose this product
In a word, it's just Plastic
As it is plastic, the design is as shown in the image 。
The only thing that stops it is basically Tie Wrap? So it's easy to attach
Moreover, one of them is not allowed to wear Tie Wrap
It seems to be shared with other CRFs, so I don't think there's any way around it
After all, is the attention to detail like ZETA's somewhat lacking?
4,000 yen would be more appreciated
View detail
Great!
Installed on the 2017 S1000RR
If you don't have the frame cover, it will be very hot and scalding Buy the twill weave matte finish in stock
I installed it and took it out for a test run
Before I put it on, I couldn't knee-grip in jeans because it was too hot, but now I've got the Cover It's so different! It felt like
And it looks like Carbon is casually attached to it, so a matte finish is possible! feeling like
This is the best benefit for the price!
Seriously, you should buy it!
View detail
Fits: KAWASAKI KLX250, KAWASAKI D tracker, KAWASAKI D-TRACKER-X
Poor balance between price and quality
The Frame started to get scratches on the Frame, so I bought it, and the TRAILfor Vehicle ones are not so much I didn't have one, so I went with a zeta product
It's just Hairline processing on a plate of aluminum It will be full of Wound soon
There is no problem in the accuracy of the installation & rarr; hole position etc., but if you install it as it is, you will have no problem
There is a point where it hits the Frame, but it might wound the Frame I pasted the thin rubber sheet to the strongest place with double-sided tape other (esp. people) 。
Because you can fix the Frame firmly with OffBoots, you can use Tan DIN
It's easier to ride with a gu
Because of the large gap between the frame and the guard, it is easy to catch branches, etc. on the forest road, so the course I think that soil tends to accumulate in the I think that I will put Sponge etc. in between
It looks like they have carbon and plastic ones, but the fixation was Tie Wrap
I bought this product because I thought it would be damaged by a fall, but it doesn't feel very solid Mm.... hand Gulp And I can bend it just by doing it. lol
Originally, because it is a product for the prevention of Wound, I do not care about Wound etc. in use, but the price If the product is expensive, then it has to be of a reasonable quality and look, or it's not a satisfactory product I would have appreciated it if it was a little cheaper, lol
View detail
Available for '12
Although adaptation is '15 years', it can be used even in '12 year.
People with sharp looking at the image may notice, but Nut of Front sprocket is different from '12 year made, but this has been exchanged for '14 Shaft Output Shaft.
So Frame is definitely made in '12 year.
Another one to KLX ZETAMaterial : I am using Aluminum's Guard.
When it rubs it becomes Buffing cookie and Boots become black
Because it is a plain thing of the board Gold just like Design
Material : I longed for Plastic's designed one.
Although the PRO players often watch using Sticker Type's anti-slip
I think that this is probably the most functional considering the thickness.
However, as you actually use this product, there is little sense of incongruity when Knee grip
I think that there is no problem as a function.
However, regarding installation,
I use one part of Rear brake master part
I fixed the Tie Wrap to another place like the image.
I have to relax the Bolt of MASTER and pass it through, but I am anxious that I changed it to this way.
Because the body is made in 12 years and its shape is different, it does not mean this.
View detail
It was a satisfactory item for me.
Since the heat from the Engine is transmitted as it is to Frame, I always thought that I was going to ride and burn. As I was looking for something Manufacturer out putting Frame cover, since I was putting out with Magical racing, I purchased it immediately. Delivery was delayed but quality was good, accuracy was good, and the finish was also beautiful. I feel like running rocks. Installation is not all Cowl, but I think that it is better to take it out even where the Frame is hit. Left Side needs to remove Shift Pedal.
I think that it is not difficult because even an amateur 's me could install it. It looks foolish as it looks like Carbon. It is a way of feeling the most heat, but I do not feel so hot as I do not touch it directly.
What is it like to do this Cover later on next summer?.
In midsummer, I think that it is enough if you feel as much as you do now.
View detail
Because YsGEAR's Frame guard was unpopular
I saw a comment saying that the Frame guard of YsGEAR is deformed easily like the Le Pera like this title.
There is no worry about Guard by making solid thing itself ? ? ? Is w
Although other people have also written, it is highly likely that the frame will be scratched if mounted without thinking as it is.
I am preparing RubberPlate on the contact surface to prevent scratches.
WR250R dared to make it because Frame is Silver.
View detail
There is only OEM Product and it is a good product.
There is only OEM Product and Quality is also good and expensive, but installation Bracketetc. It is a little troublesome to have to transplant from OEMTandem seat. Would you like Bracket also attached at this price? View detail
Fits: KAWASAKI KLX250, KAWASAKI D tracker, KAWASAKI D-TRACKER-X
The installation system is bad
It seemed that the position of the Screw hole was slightly misaligned as other people were reviewed..
Some sharpen etc.. I think that it will be necessary to devise such ingenuity.
Protection performance is unknown, but Knee grip may become easier.
Would not it be better to purchase it as Dress-upItems?.
View detail
Hold property rises, it is easy to control.
Because the car body is rounded slightly at NORMAL, the feeling of Hold is not bad for Off-road boots, but by attaching this Frame guard, the Hold property rises markedly.
In my riding method, footpeg and Step plate are important parts for Machine control, it is a foot belly, Heel and ankle, and it holds at various foot parts, but Frame guard is By attaching, the thickness also increased slightly, the area to be Hold increased, making it very easy to control. Although it is Standing, it is easy to get on because it has a solid feeling of Hold during Jump.
Installation method, but the installation manual was not enclosed.
I could judge by Pitch of Bolt hole of product so there was no problem but I think that Manual should be attached.
Body Right Side Quantity Heol Guard's Bolt : Remove 2 pc, add the attached Bolt to Quantity : Just tighten 2 pc.
Left Side removes the Drive sprocket cover, removes the Bolt of the Sub Frame, inserts it obliquely from the Driven Sprocket side, and tightens the Bolt of the Sub Frame. Tightening Torque, like OEM, 2. 7N - I closed with m. I think that it should be written for those who do not have a service manual in Manufacturer.
For me, rather than Frame guard, the meaning of the Step plate is Large.
As the sense of unity with Motorcycle increases, operability improves so it was perfect for me who is an off-road beginner. It is especially recommended for people who want a sense of unity with the body when the car body runs ramping when you run off-road, or those who are suffering from Control.
View detail