Reviews
In Setting.
I would appreciate it if it was a little cheaper but the quality is good so I am satisfied. View detail
YY system.
Needle is YY system with many steps is good. View detail
KEIHIN KEIHIN Jet needle
YY system is recommended because it has many steps. View detail
Fun Setting.
If you are not convinced by the Jets, try changing the Needle. View detail
Fits: その他 FCR Single Carburetor Horizontal (H/Z) Large, その他 FCR Multi-Carburetor Horizontal (H/Z) Large, その他 CR-SPECIAL Carburetor, その他 FCR Multi-Carburetor Horizontal (H/Z) Small
Easy to lose.
I bought this as a spare because it is easy to lose when changing the number of Needle steps. View detail
Fits: その他 CR-SPECIAL Carburetor
Loss.
I lost it and bought it for Repair. View detail
Fits: その他 CR-SPECIAL Carburetor
for Repair.
I bought this because it ran out during a needle change. View detail
without Hole。
I don't use a Starterb RANja, so I replaced it with one without a hole. View detail
Fits: その他 FCR Multi-Carburetor Horizontal (H/Z) Large, その他 FCR Multi-Carburetor Horizontal (H/Z) Small, その他 CR-SPECIAL Carburetor
To the air inlet.
I bought this to seal the air inlet under the Starter B Ranjer. But it may not make much sense ^^^. View detail
Fits: その他 FCR Multi-Carburetor Horizontal (H/Z) Large, その他 FCR Multi-Carburetor Horizontal (H/Z) Small, その他 CR-SPECIAL Carburetor
For KEIHIN's Rubber cap.
It is Exactly to Rubber cap of KEIHIN. View detail
In Setting.
A necessity of Setting. If it is a little cheaper, it is good because it becomes a considerable gold amount when it arranges it. View detail
Fits: その他 FCR Multi-Carburetor Horizontal (H/Z) Small, その他 FCR Multi-Carburetor Horizontal (H/Z) Large, その他 FCR Single Carburetor Horizontal (H/Z) Large
FCR28 Adjust Screw
I am using a chemical oil in FCR28 Because the original Adjust Screw has been broken The original quality is very good. Can be installed directly, no need to modify Need to buy it again --- I am using a carburetor in FCR28 because The original Adjust Screw has been cut off. The quality of the original factory is very good and can be installed directly. No modification is required. I will buy it again if necessary. View detail
not good enough
I ordered 4 #152 and 4 #155, but the delivery time of #155 became more than 2 months, and I couldn't get the #152 I ordered together in time. I'm going to buy them from Raflo...if only webike had better service... View detail
It is indeed made by KEIHIN.
It is indeed made by KEIHIN.
I have no complaints.
Webig has a lot of stock, which is great.
We never use Jet products of unknown manufacturer.
View detail
Fits: その他 FCR Single Carburetor Horizontal (H/Z) Large, その他 FCR Multi-Carburetor Horizontal (H/Z) Large, その他 FCR Multi-Carburetor Horizontal (H/Z) Small
Reliable KEIHIN OEM Parts
I used it for Carburetor overhaul of KawasakiZXR250.
About 1/3 the price of Kawasaki OEMParts.
This part is for FCR Carburetor Body, but it can be installed on Kawasaki OEM KEIHINCVK30.
There are also many other common Parts, which helps us in terms of Cost.
View detail
Keihin Slow Jet
It is OEM Product of Keihin, so there is nothing wrong with it View detail
Fits: その他 FCR Single Carburetor Horizontal (H/Z) Large, その他 FCR Multi-Carburetor Horizontal (H/Z) Large
Regular replacement parts for FCR Carburetor Body
MaintenanceCycle is important for FCR Carburetor Body unlike Normal cab.
This Rip seal and Rubber parts such as Plunger (Diaphragm) of acceleration pump are regular replacement parts.
As you know, the Throttle valve of the FCR Carburetor Body is equipped with a Roller, which rolls over the rail of the carburetor body. On the other hand, in order to prevent air from being sucked in through the gap between the Throttle valve and the carburetor body due to the negative inlet pressure, the floating Valve + Rip seal is used to keep the Throttle valve from sticking and leaking air so that it can be raised and lowered smoothly.
If the rip seal here loses flexibility or changes shape, the seal between the floating valve and the carburetor body becomes bad and air is sucked in. As a result, there is a malfunction that becomes thin especially near Idling and at AxelOff.
Since it is a cheap thing, I recommend the regular exchange of the Rip seal in the sense that I have a spare!
To replace the rip seal, you need to remove the throttle valve, so you need to do the basic assembly such as clearance and tuning. If you are worried about the precision, please ask PRO. (You don't need to worry about the synchronization in the case of single cylinder such as SR …)
View detail
main jet
Since the carburetor on the vehicle was not OEM, I couldn't place an OEM order by part number, so I bought the carburetor on the spot and thought it might be the one.
It was easy to choose to buy the same item in different sizes.
I feel cheap when I buy 1pc. unit, but when I buy several, I feel unexpectedly expensive.
View detail
Fits: Others FCR Carburetor Body Carburetor for Φ28-Φ33(Small body)
Needle
I used it to change the setting of my FCR Carburetor Body. I wanted to make it a little darker, so I went for it, and I'm happy with the Large change. If you like to enjoy setting, I think you will enjoy it very much. View detail
Fits: Others FCR Carburetor Body Carburetor for Φ28-Φ33(Small body)
Needle
This time, I changed the setting a little because it became summer, and I changed it to GTP because the bottom was thin in GTQ. It is easy to send it to the shop, but it is also fun to set it by yourself. I wish the price of Needle was a little cheaper. View detail