Reviews
poor response
The MASTER of the front brake was replaced with a type without a switch, so a hydraulic switch was used.
The Stop-lamp did not light up with a light pull, and finally lit up when I gripped it a little like a hard brake.
View detail
be extremely thorough, focusing on even the finest of details
Tank can be oriented 360 degrees to any desired angle. View detail
Fits: KAWASAKI ZZR1400, YAMAHA YZF-R1, KAWASAKI ZX-14R, KAWASAKI ZX-6R, YAMAHA YZF-R1M, Others
Quality is high.
The quality is high, but so is the price. I bought it at Webig for the Point Reduction Sale and used it for the master cylinder of the rear brake of my DAX125. I think the cost is reasonable because of the cut-outs. View detail
bremboFluid cap
Replaced because it had deteriorated and looked bad.
Screw stuck and struggled to remove.
After the replacement, it looks different.
I feel good about the ride.
View detail
The transformation with the simple addition this rear master cap is amazing
About quality and texture - The rear master cap from G-Craft is made from billet aluminum with detailed machining and a silver anodized surface finish, the quality from the overall fit and finish is perfect. About the feeling of use - I was unimpressed with the over look of the original rear brake master cylinder reservior tank with all it's plastic finishes. The transformation with the simple addition this rear master cap is amazing and I am more then satisfied with the new look. Products to buy together - A product to purchase to add a more attractive appearance to the Monkey 125 cockpit area would have to be a master cap for the front but sadly G-Craft do not have a matching product available but luckly Webike have other silver anodized options to choose from. Difficulty of installation - The installation of the rear master cap is a simple task that took 0.1 an hour to complete. Common sense and the use of your hands is all that is required to screw the cap onto the reservior tank. Cost performance and comparison with other products - I find the cost of all the products G-Craft sell to be on par when compared to what most other companies sell their products for and the rear master cap is no different. About shipping and packaging - With there being no cost difference between sea freight and EMS for the engine cap, I chose EMS for an earlier arrival date. The part was extremely well protected while being covered in bubble wrap and surrounded with air pillows in a sturdy cardboard box. Any concerns, cautions, or advice when purchasing - Webike Japan is the first place I look to for all my motorcycle needs. From service parts to performance products and even motorcycle gear and apparel, Webike always seem to satisfy my needs in regards to availability and pricing. View detail
Fits: YAMAHA YZF-R7
It is a MASTER with excellent cost performance!
[How is it used?
This will be an imprementation with 100% Circuit driving.
Was the one you received as per Image?
Yes.
As shown in the photo, it arrives in a box in Assembly condition.
Was the installation difficult?
If you are able to bleed the air out of the Brake, it is an easy category.
For workability, pull out the Fluid from the Reserver tank to the banjo bolt of the MASTER.
Next, remove the banjo bolt from the OEMMASTER, and then remove and install the MASTERBody in the reverse order.
How was your experience with it?
This time, we replaced the OEM Nisshin Radial master from YZF-R1M, and the fee rings are excellent.
The piston diameter is the same (16mm), but the lever ratio is different, making it slightly stroker. This is very effective in circuit driving, and the BrakeRelease side has a lot of Strokes, which makes control easier. I think it is better than RCSMASTER of brembo. The R7OEMMASTER is 16mm, so it is theoretically more on the Stroke side. The closest thing to a replacement Brembo master is the Racing master 16x18, but since you can get one for about half the price, this master is a very cost-effective option. Moreover, since the banjo is not located on the bottom as usual but on the side, it is highly possible to use the OEM hose. In fact, again, the Banjo bolt and Hose use the OEM as is. However, one thing to note is that brembo usually has a bolt pitch of 1.00mm, but this one has a bolt pitch of 1.25mm. Therefore, if your car is equipped with the OEM Brembo master, the pitch may not match.
[Included Parts:were they on?
There is no particular Included Parts:as it arrives in Assembly condition.
[Was there anything that disappointed you?
None
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
Two separate banjo bolt Gaskets are required for installation.
Others are basically Bolt On. The hose from the reservoir tank to the MASTER is a transplant from the OEM Nisshin MASTER, because the length and bending angle of the R7 hose are not the same. The hose here, as well as the banjo bolt pitch, has a different diameter nipple than a normal brembo.
Finally, if you are riding a YZF-R1/M and suffering from the OEM patched fee rings, I highly recommend this MASTER. It is the most cost-effective solution for the smallest cost and the largest effect. In other words, Demerit is Zero.
View detail
Fits: DUCATI DESERTX, DUCATI HYPERMOTARD 1100, DUCATI HYPERMOTARD 1100S, DUCATI HYPERMOTARD 1100EVO, DUCATI DIAVEL 1260S, DUCATI HYPERMOTARD 796, DUCATI HYPERMOTARD 821, DUCATI HYPERMOTARD 939, DUCATI HYPERMOTARD SP, DUCATI HYPERMOTARD 950, DUCATI HYPERMOTARD 950 SP, DUCATI HYPERMOTARD 950 RVE, DUCATI HYPERSTRADA 821, DUCATI HYPERSTRADA 939, DUCATI MONSTER 400, DUCATI MONSTER 620, DUCATI MONSTER 695, DUCATI MONSTER 1000, DUCATI MONSTER 696, DUCATI MONSTER 750
It's nice and casual.
It's nice and casual, the texture is okay. View detail
Fits: SUZUKI SKYWAVE 250, SUZUKI SKYWAVE 400, HONDA CB223S, SUZUKI SKYWAVE TYPE II, SUZUKI SKYWAVE TYPE I, SUZUKI SKYWAVE 250, KAWASAKI EPSILON 250, SUZUKI BURGMAN250, HONDA SPACY250 FREEWAY, HONDA XLR250R, HONDA FTR250, HONDA FTR223D, HONDA LEAD110, HONDA FTR223, HONDA MTX200R II, HONDA SPACY125, HONDA LEAD100, HONDA LEAD50
As expected of Nisshin, the braking power is also GOOD!
LEAD110 (JF19) I tried it out for the first time. I feel that the braking force and touch are better than those of the Normal pad, and the price is cheap and cost effective. I don't know about durability in the rain yet, but Caliper is also Nisshin, so I think it might be a good match.
I think the performance is sufficient for a Small Type Scooter.
View detail
Fits: HONDA CMX/REBEL250(ABS), YAMAHA XV1700, YAMAHA XV1700, YAMAHA MT-01, YAMAHA MT-01, YAMAHA MT-01, YAMAHA MT-01, VICTORY Vision Tour, VICTORY Vegas, VICTORY Vegas Ness Signature, VICTORY Vegas Jackpot, VICTORY Vegas 8-Ball, VICTORY Vegas 8 Ball, VICTORY Ness Cross Country, VICTORY Magnum, VICTORY Kingpin, VICTORY Kingpin 8 Ball, VICTORY Judge, VICTORY Jackpot, VICTORY HighBall
The packaging is, sadly,..,
Since Impression was well received, I was excited to purchase this one for myself.
Since I had just replaced the Brake fluid myself not long ago, I also replaced the pad myself.
I have been using Copa Slip to stop squeaking and this time is no different.
The Front of SEROW250 with DAYTONA's HYPERSintered was incredibly scary at first, even on the street, so I set out for a test run with a lot of caution, but it worked there and gradually got better and the break-in period ended after 15 km.
I look forward to Fee Rings at the next and subsequent Tourings.
My only disappointment is the packaging.
Does the Vesrah factory do this kind of packaging?
It arrived in a thin, bag-like Cellophane with a base paper and pad.
Go in, or rather, you can imagine what would happen if you put something that hard and heavy into a Cellophane bag.
The bag was torn, and when I unknowingly took it out of the box, the contents fell down with a thud.
It's hard to believe, but it's true.
And I wanted them to be shipped at least GRUGRU wrapped in plastic wrap,
And if they were put in a box by Webike! I wanted to make sure that measures were taken to prevent the contents from coming out,
If the packaging is this fragile at the time of shipment from Manufacturer, I can only assume that it was torn when it arrived at Webike! I suspect that it was torn when it was delivered to Webike!
Anyway, that makes me feel bad.
There are no scratches on the product and the performance seems Large sturdy.
I would have given it 5 Stars if it ran to some degree and I was satisfied with the Fee Ring, but I gave it 3 Stars due to packaging issues.
View detail
Fits: HONDA CBR1000RR, HONDA CBR1000RR, HONDA CB1000R, YAMAHA YZF-R1, YAMAHA MT-10, YAMAHA YZF-R6, YAMAHA MT-09, YAMAHA MT-09 TRACER, YAMAHA XSR900, YAMAHA TRACER900, YAMAHA MT-07, YAMAHA XSR700, YAMAHA YZF-R25, YAMAHA YZF-R3, YAMAHA MT-25, YAMAHA MT-03, SUZUKI GSX-R1000, SUZUKI V-STROM250, SUZUKI GSX-R600, SUZUKI GSX-R750
Master cylinder cap
Changed from Green Light to Gold. View detail
Fits: KAWASAKI 900 Super Four, KAWASAKI 900 Super Four, KAWASAKI 900 Super Four, KAWASAKI 900 Super Four, KAWASAKI 750SS MACH IV, KAWASAKI 750SS MACH IV, KAWASAKI 750SS MACH IV, KAWASAKI 750RS, KAWASAKI 750SS MACH IV, KAWASAKI 750RS, KAWASAKI 750RS, KAWASAKI 650RS
To Refresh Disc Rotor
I purchased this for use with my Kawasaki Z1.
I purchased this disc with HoleType because the OEMDisc Rotor was approaching its wear limit and I wanted a custom look.
When we removed the STD Disc for replacement, we found the difference in weight between the STD Disc and the Hadrill.
Along with braking power, we expect the weight difference will also change the driving experience.
Rotor replacement is not a difficult task if done carefully.
The bolt hole where the rotor bolt was removed was lightly cleaned with M8 fine tap, Locktite Blue was applied to the bolt, and the bolt was fastened at 26 N.m.
Pad should also be replaced with a new one.
View detail
Fits: HONDA CB1300SUPER BOLDOR, HONDA CB1300 SF, HONDA CB400SUPER BOLDOR, HONDA CB400SF, HONDA
Moriwaki master cylinder cap
I ordered these caps as an upgrade and to add a bit of style, my caps were as ever packaged and boxed to the highest standard,with only four screws holding these on both were fitted within minutes an easy upgrade for your cb13 View detail
Fits: KAWASAKI ZEPHYR X, KAWASAKI ZEPHYR400
Mesh hose for rear brake
It looks cool, the Crimp part is covered and looks luxurious and sturdy compared to other Hoses. View detail
Fits: HONDA ADV160, HONDA PCX e:HEV, HONDA ADV150, HONDA PCX160, HONDA PCX160, HONDA PCX, HONDA PCX
We should have done this from the beginning.
I used to use a lever with a parking brake, which is a type of brake that you push into the brake lever.
Screws loose and slipping on hills etc....
I had to re-tighten it each time.
And if you tighten it too much, the Stop-lamp stays on.
Lever fades and rattles, and I'm sick and tired of the inferiority of Chinese products.
I reverted to OEM Brake lever.
I found this product on YouTube, purchased it and installed it.
Installation itself is very easy.
The effect is also Outclassing
Why didn't I buy it sooner?
View detail
To Refresh!
[How is it used?
I purchased this because the Cap had become crusty and decayed over time.
The Release part of the Clutch was replaced.
How was your experience with it?
It is new, so it is soft and tight.
And with bremboLogo, the tension is increased.
How did it compare to other products?
There are other cheaper Caps and such, but if it is only a few hundred yen difference, bremboCap is the way to go!
And it is a reliable Manufacturer.
[Points to note]
I will remove it properly from now on when I bleed air.
View detail
Fits: KAWASAKI Z1000 (water-cooled), YAMAHA V-MAX 1680, TRIUMPH DAYTONA675, SUZUKI GSX-R600, SUZUKI GSX-R1000, SUZUKI GSX-S1000F, SUZUKI GSX-S1000, SUZUKI B-KING, KAWASAKI ZX-6R, HONDA VTR1000SP, Others
Parenthesis good!
I bought it because I wanted to have the same type of Brake and Clutch. View detail
Fits: KAWASAKI 1R, KAWASAKI GPZ900R, KAWASAKI KR-1S, KAWASAKI ZRX1100, KAWASAKI ZRX1100, KAWASAKI ZRX1100 2, KAWASAKI ZRX1100 2, KAWASAKI ZRX1200DAEG, KAWASAKI ZRX1200R, KAWASAKI ZRX1200R, KAWASAKI ZRX1200S, KAWASAKI ZRX1200S, KAWASAKI ZRX400, KAWASAKI ZRX400, KAWASAKI ZRX400 2, KAWASAKI ZRX400 2, KAWASAKI ZX-12R, KAWASAKI ZX-12R, KAWASAKI ZX-12R, KAWASAKI ZX-12R
Just received them
I just received my package. Everything is well packed,thank you. Tha brake pad pins looks very nice and high quality. When i install them in a few days i will write more View detail
Fits: KAWASAKI ZRX1200, SUZUKI GSX1300R GSX1300R HAYABUSA, SUZUKI GSX-R1000, SUZUKI GSX-R750, SUZUKI GSX1300R GSX1300R HAYABUSA, SUZUKI GSX-R1000, SUZUKI GSX-R1000
Brembo caliper essentials
I was going to buy KOHKEN 18mm, but I chose this one because the hard anodized aluminum one was discontinued.
The thing is well made and just fit the OHLINS Fork.
Since it is made with high precision, I installed it by tapping it with a Hammer a little and press-fitting it.
It is better than I expected.
View detail
bremboIncluded Parts:for compatibility with
I bought a battered 900SS (900SL) and am Restore.
I scraped together various Brand components to make a footpeg, but as expected, the stop lamp switch did not look good.
I really wanted to use a mechanical switch, but I didn't want to grow a small bracket to hold the switch in place or to hook the spring, so I decided to use a hydraulic switch.
I hate Hydraulic Switch because it makes PedalTouch worse...
However, my ankle does not move very well, and it is impossible for me to step on the rear brake while cornering.
I was so quick to buy a Switch with Pitch 1.25, but this product is properly Pitch 1.00.
Everyone should make sure that the Pitch is correct before purchasing.
The shape is the Hydraulic Switch itself, which is included with the recent brembo RACINGMaster Cylinder.
The only difference is that the color on the wiring is blue while brembo's is red, but the construction and precision are no different from brembo's. The only difference is that the color on the wiring is blue while brembo's is red.
If I had to say, the condition of Mt. Screw is rough...? It's about the same.
I think the manufacturer is probably the same as brembo.
Then, by visual inspection and operation Check "Superiority." The determined items would go to brembo.
This Babyface product seems to be the next best Level product.
(95 point product that looks and works fine, but not as perfect as brembo)
My guess is that the very cheap Chinese Switches sold on Amaz0n are made in the same factory, and those that did not reach the passing line in the inspection (those of a level that cannot be sold as made by brembo or Babyface) are not disposed of and are being sold on the side.
I don't know.
Anyway, this product is normal and problem free.
It is working properly and stably.
Oh, but I was worried about Screw Pitch only, so I put it through Dice beforehand.
But it was only a part of the Plating layer that was caught, so it was Large sturdy Level even if it was used as it was.
View detail
Fits: HONDA CRF150F, HONDA CRF230F, HONDA CRM250AR, HONDA CRM250AR, HONDA CRM250R, HONDA CRM250R, HONDA XLR125R, HONDA XR250, HONDA XR250 Baja, HONDA CR500R, HONDA XR400R, HONDA XR230, HONDA SL230, HONDA XLR250, HONDA XLR250, HONDA CR250, HONDA XR600, HONDA XR650, HONDA XR250, HONDA XR250MOTARD
Yearly update?
I replaced the Front Disc on my 89 MD24.CRM250RK with a new one due to a Brake Overhaul. The original Rotor is still usable, but I replaced it hoping for a slight improvement in touch. The replacement was easy, but the OEM front hub cover could not be installed, so I applied anti-loose agent according to the service manual and tightened at 1kg/cm (98N/m). In the test run, I did not feel any difference in the touch and the braking power, partly because I had not yet gotten accustomed to the pad.
However, the lack of wear would be expected to improve Touch.
View detail