Reviews
good quality goods at a low price
It was very inexpensive for Carbon and was thick enough!
The edge finish is a little rough in some areas, but for the price, it's acceptable.
You can polish it with Paper and
View detail
Hole position is perfect.
[How is it used?
I came across this product after searching for a variety of products because the XJR400R I purchased did not originally come with a front fender.
I would have preferred OEM, but buying a used one would cost about 5,000 yen or more, including shipping! So we chose STING R&D products, which had been used in different models of cars.
Was the one you received as per Image?
The carbon grain is beautiful when viewed from the front.
The reverse side is FRP, so only the surface part visible from the front is covered with Carbon.
The edges are a little rough in some areas, but at this price, it is acceptable.
Was the installation difficult?
The XJR400R was easy to replace because the Tire could be replaced with the Tire still installed.
The front fork has a clearance and 4 hole positions that are perfectly centered, so it can be installed without difficulty.
However, the hole size is too small to accommodate OEM colors.
If a collar is to be inserted, the hole must be expanded.
How was your experience with it?
I chose the twill weave Carbon type, and I am quite satisfied with the appearance.
It turned out to be Style as I had expected without any particular cheapness.
The hole for the cable guide was also well drilled.
[Included Parts:were they on?
Front Fender only.
Bolts and colors are required separately, of course, so it would be better to have the original or OEM parts.
[Was there anything that disappointed you?
There were some problems with the edge treatment and hole Size, but considering the price, it is acceptable enough.
【Review】
It can be installed on XJR400R without any problem.
I am generally satisfied with the product, although there are some compromises that need to be made for the price.
Also, Webike did not have it in stock this time, but I received it within a week.
View detail
Satisfied with Cospa
[How is it used?
NSR250R in Restore (MC21) I purchased this product, which was relatively inexpensive, because there were no Front Fenders available in the market.
Cowl will be painted later, so I was looking for a Carbon one that I didn't have to bother painting.
Was the one you received as per Image?
It was inexpensive for Carbon, so I thought the quality must be bad anyway, right? I tried to look for roughness, but there were no scratches or distortions at all.
Sorry for doubting you, it was more solid than I thought it would be!
Was the installation difficult?
OEM Bolt and Bracket type Nut are required for installation.
As of July 2023, both are new and OEMParts were purchased together.
Both SIDEs were temporarily fastened and tightened, and there were no problems with the accuracy of the hole positions or Fork relief.
How was your experience with it?
It is as shown in the picture, but it was installed securely and Center is almost out.
I thought some processing etc. would be necessary, so I was pleasantly surprised.
It is definitely better to use this product than to use a Chinese PeLePeraFront Fender, which I do not understand.
[Included Parts:were they on?
There are no Included Parts:for this product only.
There is no Instruction Manualetc., although it is not particularly necessary.
[Was there anything that disappointed you?
Not at all!
【Review】
The product is inexpensive, but the quality is not bad at all, it is better than I expected.
If you are not particular about Style, I think you will be fully satisfied.
View detail
Carbon fender and side cover
Since we switched to carbon side covers, we also changed the front fender to carbon.
I was able to install mine without modifying the Side cover or Fender.
I think the Fender mounting bolt will be replaced by a different length.
View detail
To the car body that is being Restored
The suspension of an NSR250 was used on an old vehicle that was being restored, and it was installed on it.
Perfect! Great cosmetics.
View detail
Purchased Black Gel but has deep scratches.
Buy Black Gel
I understand that Black Gel is a prerequisite for painting, and I can understand abrasions, small scratches, etc., but I'm not sure.
There were deep scratches on the Pate fill Level.
I thought it was defective and inquired about it.
They told me that the manufacturing mold was damaged and that I would receive the same one even if I exchanged it.
It seems to be a good product.
If you are good at Cowl processing and can handle Level Cowl from Pate embedding, it is good because it is less expensive than other products.
View detail
Carbon Front Fender for R1-Z
The black texture of the carbon matches the white color of the R1-Z, and the impact of the look is considerably different.
The strength is also Carbon, so it is lighter and has a better texture than OEM.
[Color] Clear finish, but again by myself for UV protection. [Color] It is likely to be more durable if it is installed after clear coating.
It is more secure to remove the front tire for installation, but if you are prepared to get scratches and try to force installation, you can manage to install it.
View detail
Fits: KAWASAKI Z1000 R All years, KAWASAKI Z1000 J All years, KAWASAKI Z1000 R All years, KAWASAKI Z1000 J All years
sufficient for one's needs
I think the accuracy is sufficient for Refresh of the exterior.
It is much cheaper than finding an OEM used paint base, and you don't have to be fed up with distortions and poor workmanship.
View detail
Fits: KAWASAKI Z1000 J ALL MODEL, KAWASAKI Z1000 R ALL MODEL
Bikini cowl
Asked Motorcycle shop to make Bracket and installed it.
Installation method similar to that of the Z1000R OEMBracket.
specific range of rpm (3,000 RPMs) Is it because of the thinness of the flesh that the sound of the scared is produced in the
Circuit use for Repair would not be a problem.
It is expected that the hole will be slightly gapped when combined with DOREMI's Screen.
View detail
Can be used for DUCATI SS and Initial ModelMONSTER S2
It can be used for the 900SS, 750SS, and Initial ModelM900 of the 90s. Many of the exteriors for older models are no longer available, but we appreciate your support. View detail
Cospar good
I bought this as a replacement for my OEM Fender that I broke in a fall.
The OEM shape is the same as the original, so it can be popped on.
For installation, Nut cannot be used, so it must be prepared separately.
Also, note that the R1-Z requires the front wheel to be removed to remove the fender.
It has enough texture and I like it.
View detail
Fits: YAMAHA TZR250 3MA upright type, YAMAHA TZR250 3MA upright type
The thickness of the mounting part is a little thin
Mounted on a RZr with 3MA feet.
When I installed it, the width was a little narrower than the actual size, and I felt like I had to tighten it while spreading it out, but there was no problem installing it, and the accuracy came out well and I was able to install it straight.
The thickness of the mounting part is much thinner than OEMFender, and I couldn't fix it even if I tightened it to the root with Bolt which I had been wearing, so I fixed it by biting SiliconWasher which I have.
I don't think changing to a shorter Bolt would cause any problems.
I was grateful to be able to buy Reasonable because the used ones in good condition are expensive in discontinued Parts.
View detail
Cospar good
It's STD Shape, so you can use it without feeling uncomfortable. View detail
beautiful side panels made of carbon
very nice side parts made of carbon .. fit 100% and are made very precisely. Would buy these side panels again and again. I chose Twill Weave. The price is ok and the shipping was really quick too. -------------------------------------------------- -------- Very nice side panels made of carbon .. fit 100% and are very accurate. Would buy these side panels again and again. I decided for Twill Weave. The price is OK, and the shipping was also very fast. View detail
Almost good
I had to shave it down a bit to Adjust it to my Motorcycle. I'm happy with the quality and rigidity. View detail
Inexpensive Parenthesis
Front side is Carbon fiber and Reverse side is Glass fiber.
The so-called Wet Carbon
Still, the product is satisfactory in both appearance and accuracy!
Installation on GSF1200
Just remove the OEM Fender that is bolted to the Front Fork Stabilizer and put it back on!
However, there is a reinforcement plate on the FenderReverse side, which could not be fixed with double-sided tape due to the unevenness of the glass fiber.
I used masking tape to hold it in place before I installed it.
I was optimistic that the Masking tape would come off while I was running.
View detail
The construction is good! Price is right! The seams are there...
Installed on NSR50 late model
The OEM is a small Fender, but I found and bought this one when I wanted to install a large carbon one because of the design. It is 26 days from the order to the shipment, so I think that if I look at 4 weeks including arrival, there is no mistake.
I opened the package and my first impressions were as shown in the picture. "Carbon seams, Center..."
Weight Carbon products with complex shapes have unavoidable seams.
I couldn't see where the seam was in the picture shown on the website and was wondering where it was before I bought it, but it was at the Center.
It's also more noticeable than you might think in terms of eye direction.
I'm a little disappointed because I didn't buy it knowing from the picture on the listing that the seam was in Center.
[Color] The ClearGel coat is also very thick, so I didn't feel any bumps at the seams.
The product itself is
It is thick and has good strength.
As you can see in the picture above, there is not much room for play, and it is not flexible due to its high strength.
Overall, I think it's a good product because it's inexpensive and strong as a Weight Carbon product.
However, due to the strength and thick Gel coat, it is a little heavy and
Design-wise, the seams are a concern, so
If you are focusing on lightness and appearance, I don't think you will appreciate it very much.
View detail
Fits: YAMAHA Up to XJR1300 model year, must be the same shape
This is for RP01J. Please make sure you have the correct one.
I'm getting tired of the OEMs, so I'm replacing them.
We didn't have the stones in stock, but we had them made, and that's where they were. I like it. I know!
I appreciate the feeling that it was made just for me!
I'm going to use it for a big thing.
The hole of the bolt is a little bit out of alignment, but it's not a problem because Carbon parts are designed to be machined small.
View detail
Fits fine
Purchased as a replacement for an OEM Fender due to age-related deterioration.
I was able to install it as it is without any special hole processing. However, because there is no color of the genus Gold like the OEM Product, I think that there is a little hang to the alignment of the Mounting Bolt.
The appearance is also Carbon style and looks good, and it became a tight appearance with Black.
It will be large and durable for a few more years.
View detail
Bolt hole position is incorrect.
OEM Front Fender and Right rear bolt holes are in different positions and could not be installed.
We asked for a replacement, but it was returned to us without question.
The manufacturer says it is the same as the OEM Product, but our own 2Quantity:Set Front fork is also an OEM Product and doesn't fit into either of those categories, so I can't support the manufacturer's claims at all.
View detail