Reviews
Quality is good, but accuracy is subtle.
The quality of the carbon itself is fine, but the accuracy of both SIDES is not so good. The tank cover itself is difficult to install, because it is made in the shape of the tank cover, and the gap is inevitably caused by the thickness of the double-sided tape. Well, I think every manufacturer has this kind of accuracy.
Tolerable.
View detail
It's not quite Exactly.
It seems to be handmade, so it's not exactly Exactly.
I think Cool.
I was worried about the double-sided tape alone, so I dotted Coking on an inconspicuous spot on the edge and installed it.
I don't feel out of place when I go Touring.
View detail
So so
Was the one you received as per Image? Yes
Was the installation difficult? So so
How was your experience with it? Good
[Included Parts:were they on? Yes
[Was there anything that disappointed you? Mounting holes are not precise enough.
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
View detail
Not good
Was the one you received as per Image? Looks like a zero.
Was the installation difficult? Processing is required. Level that needs to be re-drilled for screw holes.
How was your experience with it? Good
[Included Parts:were they on? Yes
[Was there anything that disappointed you?
Installation system is not very good. Requires drilling of screw holes, etc. Drill and Leutor required.
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
View detail
Mounting.
Cannot be installed as is. (Quantity:Pair (for Left and Right) The square hole for the bottom hook was too small, so I had to cut it out and install it. The checkerboard pattern also looks smaller than in the picture. I am a little disappointed because I ordered and waited for a long time. View detail
Nut is not well fixed.
Purchased to remove the flap valve and make it full power.
It took 7 months to deliver the product.
Replacement from Straight machined OEMDuct, weight reduced from OEM approx. 350g to approx. 285g, which is like an error.
With a weight difference of this magnitude, I would like to see the product sold at a lower price in resin instead of Carbon.
I bought an OEMCap (92066-0717) to plug the hole in Solenoid, I wanted it to be plugged from the beginning because I don't think people who replace such parts would leave Solenoid.
The Gasket with the Frame is made of 100-yen Gap Sponge.
Installation is quite tricky. Both Duct and Frame have BALI at the Center, so they are like Seesaw and do not go deep enough.
When the bolt is forcibly attached while pressing down, the nut on the duct side rotates and cannot be tightened or loosened....
The OEM has a star-shaped nut embedded in the outer diameter that does not rotate, but this one has only a lightly crimped round type nut, so it rotates all the time.
In the end, I managed to install the FrameCenter by shaving the contact surface of the FrameCenter. I don't plan to remove it, but I'm not sure if it will come off since I put a screw lock on it.
The intake changed to Large width, so I adjusted the ECU before starting, and the effect was excellent.
The Torque is clearly increased from the start, and city driving is easier.
Motorcycle is a monster to begin with, but the Peak power has become even greater, and it cannot be handled by ordinary people.
View detail
Looks good, functions...
We purchased A-TECH with the lightest weight possible to protect the Engine Case in the event of a fall.
Compared to Aluminum Cut-out ones and GBRACING, the protection performance does not look promising.
The appearance will be the best Merit.
I wonder if I will ever actually fall over and repurchase depending on the Damage condition.
For installation it is necessary to modify the holes in the product and part of the drive sprocket cover in Leutoretc.
I did not find it to be a particularly Large problem.
View detail
Fitting Worst
Purchased to prevent Swing Arm and Rear suspension from being sandblasted.
FRP was selected because it is not required to be strong and its weight is not so great, and the weight was about 300g.
The delivery time was too long, it took 4 months to arrive.
Simply remove the OEMFender and slip it on.
The fitting is the worst, the radius is not in line with the swing arm, and the screw hole is gapped by about 1pc.
There is no molding defect etc. and it does not seem to improve even if it is exchanged, and I cannot wait 4 months again, so I used it as it is.
Widen the hole and forcefully push it into place, Quantity:Pair (for Left and Right) was no way Tie Wrap fixed.
The Left Side is almost invisible, but the Right Side is quite visible.
I have not driven in rain or dusty places yet, but it seems to be effective as it completely blocks the front of the Swing Arm Tire due to its shape.
It's not obvious, but it looks good, like a motoGP Swing ArmSpoiler.
View detail
To
After purchasing through a dealer, I installed the bracket at the back of the water pump side and the bracket at the exhaust pipe on the right side by myself. The bracket on the back side of the body is 10N on the water pump side and 12N on the clutch cover side, so we tightened the Both Sides by inserting the scissors with a large size Flat Washer. I had to quickly put it on or drain the oil and coolant once. Especially around the catalytic converter and exhaust pipe, it gets hot.
After installation, the exhaust pipe on the right side of the Idling got hot very quickly, so I modified the bracket, washer, collar, etc., and adjusted the position of the pipe.
After that test run, the wind entered during driving and there was no problem with the exhaust pipe on the Right Side, but the Chain on the Left Side interfered with it. I adjusted the position again, shifted the position of the collar, and offset it to the Right Side. The next test run, there was no interference, but the exhaust pipe on the Right side did not have enough clearance, and a stone was caught between it and the Heat Insulating Material, If you smell burning smell when idling, it would be better to check it once.
View detail
anti-mudrooming measures
[How is it used?
For wet road surfaces. It is said that it is originally for rectification purpose.
Was the one you received as per Image?
There are some roughnesses when viewed up close, but nothing that would cause problems in use.
Was the installation difficult?
If you install it without removing the Silencer on the side, the difficulty level will increase.
How was your experience with it?
Dirt splatter can be prevented to some extent.
[Included Parts:were they on?
Instructions are included.
[Was there anything that disappointed you?
There were some Bolts missing, but when I contacted the Manufacturer, they sent them to me immediately.
The inspection is lax, but the response is good.
View detail
attachment
Installation was more difficult than expected. The shape is slightly different from OEM. View detail
Large is Small in size but
The best part is the use of Carbon.
It is much smaller than most vessels (about half the size of a mosquito coil), but I think it would look good as a mere ornament.
One point. It is so light that I worry if the vessel will move in the wind.
View detail
Cannot be pontoon-mounted.
The design is excellent, but installation requires shaving the body and widening the holes to fit the car.
This time it is Carbon, but the FRP one I bought before could not be pontooned.
It is an Exclusive Design product and not a cheap one at that, so I wish they would think a little more about it.
View detail
ApriliaRX125 The one and only Rear Carrier
Although the Carrier is delicate, it is fixed to the car body at six points, so there is no need to worry about its strength when the Small TypeBox is installed.
The beauty of the form that follows the body of the bike without losing the flowing, radical design of the RX125 is nothing short of superb! This is a very important point because most of the people who choose this Motorcycle are in love with the Motorcycle's design and buy it!
The only problem is that the paint film is thin, so if hard objects are placed on it or it is stored exposed to rain, it will rust quickly.
However, it is the one and only Carrier for ApriliaRX125, and I think it is a good product that I can confidently recommend to all RX125Owners, including its designability.
View detail
Carbon has a nice texture, but ...!
The quality of Carbon is good and luxurious, but as you can see in the image, Tank's Quantity:Pair (for Left and Right) There is about 1 to 2mm of float in the part of the Curve of the I wish it was a little fitter. View detail
Fits: HONDA CBR250RR(2017-)
Full CowlSPL
I fell in love with the design, ordered Full Cowl SPL and finally installed it after a long wait.
I could not understand it with just one Instruction Manual, so I had to do a lot of processing in my own way.
The condition of the Fitting is
Upper Cowl interferes with Light unit and removes Meter cover
H4Wiring was made by myself, Screw position of Mirror was not aligned and drilled again, Cowl was deflected when Screen was installed.
The part where the rectifier plate is attached is long and interferes with the front fork, so it is cut off.
SIDE can be installed without any problem
Under Cowl interferes with Quick shifter and cuts off the entire Right screw fastening part and cuts off and extends the Cowl around the STAND
Exhaust pipe is cut and extended where it interferes.
Pate correction is required for steps and gaps between each cowl.
Fitting alone took up half a day.
But I'm happy with the way it looks now that I've installed it in my own way!
If I could, I would throw it to Motorcycle shop...
View detail
Made of dry carbon, but the price is reasonable.
I waited six months and finally received it.
I don't know if it is because of the times we live in, or if it simply takes longer to burn dry carbon, or if it is just until the orders accumulate, but I had to wait quite a while.
Previously, we used Magical racing's Carbon, but it was about 2mm thick and we were concerned about the bumps.
This product is dry carbon, which means that it is thin but does not get saggy under pressure.
Quantity for installation:Pair (for Left and Right) I could not install it without dropping the corner of the Also, there seems to be some distortion and the area where the knee hits is floating.
Double-sided tape may be better to be water-stretched and fixed for a while 。
However, the floating part became a hook, and it became easier to support the body, which was a pleasant miscalculation.
The reverse side is bare carbon, so I scratched the tank a lot when I took it on and off a few times.
Also, Tank Pad seems to be very selective about products because of its shape, and the one I had purchased could not be applied in the regular way.
Fitting would be even easier with a parts cleaner and a leutor for degreasing.
View detail
For Radiator protection, these are the best
Installed in addition to the Fender extension on the front.
Maybe this will make Radiator Large sturdy...surely.
Mounting is done with the Quantity:Pair (for Left and Right) Simply remove and friend-tighten the Radiator cover of the
The only regret is that it is only available in Silver. since the Radiator was also in Black on a Black car body, I painted it with a Spray can to match the color.
Large sturdy, even if appropriate, for areas that are not well visible.
View detail
Rigidity is low.
[How is it used?
It is used as a Tray for servicing.
Was the one you received as per Image?
I thought it was a rigid Tray but it is not rigid and cannot carry heavy objects.
[Points to note]
As mentioned above, rigidity is low.
At first I bought it thinking I could use it as a Tray to put food on.
It has low rigidity and can only be used for placing Bolt and other Parts at most.
after [Color] Clear paint, so it scratches easily and is normally noticeable.
How did it compare to other products?
The Coaster from the same manufacturer was so thick and rigid that it could not be shaken by human power, so we bought it thinking that this product would be the same.
It was a selfish disappointment on my part for not checking directly with Manufacturer.
[Opinions and requests to Manufacturer
Please develop a tray with high rigidity, even if it is heavier.
View detail
It is as good as expected.
Fit the Radiator exactly as shown in the photo.
I think it is quite decided.
It would be helpful if it is mentioned in the Instruction Manual.
View detail