Reviews
Fits: HONDA XR250R
It could be used on a 92 MODEL XR250R.
This is a review of a previously purchased product, it worked on my 92 MODEL XR250R. There were no problems with either installation or actual driving. The durability is unknown because of infrequent use. In my case, it worked fine, but it is only an AfterMarket product, so I guess you have to discount it in case it doesn't work. View detail
Fits: YAMAHA YZF-R1
It was fixed with no problems.
Due to a pre-existing condition of YZF-R1, the carbon brush became unevenly worn due to oil intrusion into the inside of the cell motor, and part of the unevenly worn brush came in contact with the shaft, damaging the coil. However, the mounting holes were drilled at an angle, and when I checked the inside, I found that the brush had two points of contact and the performance was down, so I returned it and re-built it with this product.
The replacement itself requires the use of a solder iron, or be careful because the internal wiring can be attached in either the forward or reverse direction, and the tightening torque is 5N, which is quite delicate and can cause further damage if done improperly.
View detail
Fits: YAMAHA DT50 L|C, YAMAHA PW50 1986 - 1987, YAMAHA PW50 1990 - 2009, YAMAHA PW50 2012
Replace deteriorated charge coil of DT50 with external one
I drive a 1991 DT50.
Recently, the engine has been slowing down, and the engine stalls while idling. The engine did not stall while driving. Once the engine stalled, it could not be started immediately with KICK and had to be pushed.
The stall during Idling had stopped without warning, even though it had been turning at 2000 rpm normally until then.
Also, during Idling, the Blinker did not blink when attached, and the Indicator did not blink.
I removed the Flywheel and measured the resistance value and found that it was only 130Ω while it should be 295Ω±10%.
So I tried to buy OEM Product but it was discontinued and not available.
I looked for it on the Net and RICK’S MOTORSPORT ELECTRIC RICKWasteMotor sportsElectric Charge coil YAM [2102-0280] was available. However, when I looked at the compatible model, it was DT50 L|C year:88-90.
I bought it anyway and compared the actual product and the shape is the same.
I installed the flywheel puller immediately and found no problem. For installation, you will need Special Tool's Flywheel Puller, a soldering iron, and solder.
The engine starts with one or two kicks, and the engine no longer stalls when idling. Also, the blinker during idling is now blinking.
I have driven more than 300 km since installation and there are no problems.
If you are experiencing any of the above symptoms, we recommend this Parts.
View detail
Fits: YAMAHA FZ700, SUZUKI GSX-R750, SUZUKI GSX-R1100, KAWASAKI ZX-11 Ninja, KAWASAKI Z250FT, SUZUKI GS550E 1978 - 1980, SUZUKI GS1100GK 1982 - 1984, SUZUKI GS1100G 1982 - 1984, SUZUKI GS1000L 1979, SUZUKI GS1000E 1978 - 1980, KAWASAKI ZG1000 1986 - 1990, SUZUKI GS1000 1978 - 1979, HONDA CBR1000F 1987 - 1988, HONDA CBR1000F 1990 - 1991, HONDA VFR700F 1986 - 1987, HONDA VFR750F 1986, KAWASAKI KZ1100 1981 - 1985, KAWASAKI KZ200 1978 - 1979, KAWASAKI KZ400 1978 - 1979, SUZUKI GS850G 1979 - 1983
BrushSingle Body by Starter
This is an OEM form of Carbon brush. You need to replace it periodically because it wears out. It is not easy to get the brushSingle Body. Soldering is necessary, but I think this product is very helpful for maintaining old cars. View detail
Fits: HONDA XR250R
xr250r me06 CDI
The parts arrived yesterday and I replaced them immediately.
After the replacement, the engine was started with one shot of KICK. I will look at it for a while with this.
View detail
Fits: HONDA CBR1100XX BLACKBIRD, HONDA CBR900RR
Thank you for not having OEM parts
The '97 Manufacturer did not have any OEM parts and I was looking for them The shape of the coupler was a little bit different, but I was able to get it to fit It's fixed with a After the exchange, the voltage is stable View detail
Fits: TRIUMPH Speed Triple 675, TRIUMPH Daytona 675, TRIUMPH Speed Triple 675R 2011 - 2012
It can be used as a substitute for OEM
OEM Parts are expensive so I was looking for alternatives. Of course you can also do installation without problem, it is a passing Level. Although I do not know about durability yet, OEM has 20,000 kilos, but it may be better to replace it with expendable items at around 10,000 kilometers. In that case I would like to Repeat. Other Manufacturer also out of other Brand Product, but it is better that this one is Coating resin. View detail