Reviews
Rubber Receiving Straight
It is easier to use than the L receipt and can be lightly Lifted up.
I am also wondering about the durability of the Rubber.
View detail
![Repair and Optional Parts] Optional Adaptor for Front Stand Mini [Coming in late July, 2022].](https://img.webike-cdn.net/catalogue/images/107032/28153_TS.jpg)
Fits: HONDA GROM
Ideal for groms
Thank you for all your help. Thank you for your prompt delivery.
I purchased a Daytona Front stand2 and used it to replace the tires on my Grom jc75. However, the attached boss was too short and it hit the jaw of the headlight, so I had to remove the headlight each time, which was a hassle. (Moreover, I had to remove my own Hazard Relay circuit and my own Fog Relay circuit, which was also quite a hassle).
This boss I purchased can be attached not only to the Front standMINI but also to the regular Front stand2. It attaches normally. It can be used normally.
■Maintainability has been dramatically improved.
■No more hassles of removing Headlight every time.
I use Front stand2 because it is wider and easier to work with than Front standMINI if I want to tinker with the front area.
For a while, I thought about making a custom-made one at Misumi, but I think this boss is the right choice Cost-wise. I want a lathe.
View detail
Stand for Beginner did not fit and I purchased an additional one.
At first I was scared to do STAND Up and Down, but once I got used to it, it was easy. View detail
Better than Hook type
I used to use Hook type STAND, but I changed to VPlate and will compare the two.
The groove of the shaft and the Plate mesh with each other, so the Quantity:Pair (for Left and Right) The stability of the system is stable with little blurring of the
Material:The plastic material provides good sliding and reduces the force required for Lift.
The Hook type can be scratched by rubbing against the Swing Arm if one is not careful, but the V-Type is less likely to be scratched because the roller part runs away from the Swing Arm to the outside.
Hook type has a risk of damage to the swing arm or the female screw when it falls over, but the Plate type does not.
As for the demerit, the Plate on the body side is more expensive and heavier than the Hook type, and the Roller itself is also expensive.
Plate is definitely better than Hook if budget allows, as Merit is the only one in use.
View detail
Put it on the Body...
I can't use it without it, so I bought it, and I want it to be Standard Equipment. View detail
It's stable.
It is considerably more stable than the V-receiver. It's usable. View detail
Purchased for 92 Grom RearMaintenance
It is sold separately from Narrow Roller Stand 8-18, so there is nothing special about it, but it looks sturdy.
The BoltHandlebar for positioning is plastic, so I am concerned that it may break over time, but if it is not tightened too much, it may be large and strong.
The contact part of the Swing Arm is Silicon type? I think this is a good idea because it reduces the risk of damaging the Swing Arm by a large amount.
View detail
high
You can't float without it.
They are solid but expensive. A few years ago you could buy them for 2,000 yen, but the quality hasn't improved and they are getting more and more expensive.
The cosmetics are very poor.
View detail
Replacement from L-shaped receptacle
[How is it used?
Maintenance Hook bolt was installed on a Kawasaki Z400.
Z400 (New ModelNinja400/250Series) The ABSSensorWiring of the Rear brake is located directly under the Swing Arm, and an L-shaped bracket may cause the Wiring to become engaged and break, so a Hook bolt and this product were prepared.
Was the one you received as per Image?
As per Image.
The plating was well finished, and naturally there were no Bolt defects, so we were satisfied with the quality of the product.
How was your experience with it?
The hook bolt is also made by JTrip, so it can be fitted with a Large change and easily STANDed.
Naturally, SensorWiring is not interfered with and is stable even when STAND is applied, so maintenance is also facilitated by the Large change.
For vehicles with a hook bolt boss, it is highly recommended to install a hook bolt and STAND with the V receiver.
I regret that I should have realized this quality earlier.
[Points to note]
I may not have adjusted it properly, but the side of the V-supporting part hits the swing arm, so when it does, I think it is better to cure the gold part with something as shown in the photo.
I cure myself with Vinyl Tape.
How did it compare to other products?
Compared to JTrip's L-shaped receptacle, this product's V-shaped receptacle is definitely easier to STAND and has outstanding stability even when STAND is applied.
I have maintained all but the Off-road vehicles I have driven in my career with the L receiver, but I wish I had changed to the V receiver earlier.
[ITEMS TO BUY TOGETHER
Hook bolt
Tapeetc. curing the side Gold genus part of the receptacle.
View detail
Cheap insurance and peace of mind.
It increases peace of mind because you no longer have to worry about the receiving Bracket coming off and damaging the vehicle body. It is a cheap insurance. The question is how long it will last in terms of strength. View detail
That's j-trip!
I bought a Maintenance Stand for my MONKEY125 and this "V receive" purchased
I have only used it a few times, but will review how it feels at this stage.
First of all, the quality is very high quality, and the material seems to last for 10 years even if used hard.
This V-receiver is protected by Rubbers front and rear, so it is not likely to scratch the body of the car (even if it is used incorrectly).
The drawback would be the high price. I think the price is reasonable for this texture. However, if you get the maintenance stand and the receiver together, it will cost you quite a lot of money. But it guarantees peace of mind.
Beginners should be careful not to install in the wrong direction.
View detail
Fits: DUCATI MULTISTRADA 1000DS 1000, DUCATI STREETFIGHTER848, DUCATI MONSTER796, DUCATI Multistrada 1100/S, DUCATI MONSTER1100EVO, DUCATI HYPERSTRADA, DUCATI MONSTER1100/S, DUCATI HYPERMOTARD796, DUCATI 996, DUCATI 998, DUCATI 848, DUCATI 916, DUCATI 748, DUCATI 748, DUCATI 848, DUCATI 916, DUCATI 996, DUCATI 998, DUCATI HYPERMOTARD796, DUCATI HYPERSTRADA
Used on ducati998.
This is Shaft, a cantilevered Roller stand.
Without it, nothing is possible.
If it is a compatible caliber, it will go in easily.
I used it for about 4 years and it was not damaged, just rusted.
Rust used AZ rust inhibitor.
View detail
Fits: KAWASAKI ZRX1100, KAWASAKI ZRX1200, KAWASAKI ZRX400, KAWASAKI ZRX1100, KAWASAKI ZRX1200, KAWASAKI ZRX400, KAWASAKI ZRX1100, KAWASAKI ZRX1200, KAWASAKI ZRX400
Well thought out and well made.
I had been using an OEMMaintenance Stand, but I was fed up with the difficulty of making it stand up, so I used this product at the same time I purchased the WideShort roller stands.
It was lifted so lightly that it was as if it had never been there before.
View detail
Exactly on REBEL250
I am using it with J-TRIP SUPER Low (JT-1203) for use with REBEL250.
The Rubber is solid and takes the Rebel 250 well.
The fact that the Rubber does not interfere with the Silencer due to its height from the mounting bar was also a deciding factor in my purchase.
View detail
Graduated from Stand for Beginner (laughter)
I used to be careful and put the front wheel on WheelClamp before hanging Stand for Beginner, but if I use Clamp, why not just use V-shape? I now realize that this is not the case.
The V-shape is so deep that there is little risk of dislodging.
View detail
The quintessence is a dedicated product. However, this is …
[How is it used?
Used on HONDA GROM JC92.
We are using it attached to J-TRIP's Front stand, but the STAND we are using is Mini stand Not STAND, but STAND in normal Size.
I do not think this is the way it was originally intended to be used, but the installation itself is possible.
Was the one you received as per Image?
Yes.
There were some areas that were not anodized, but we believe that these were areas that came into contact with the hanging strings during anodizing.
However, I was not bothered by it because it is a part that is used to GunGun with the car body in the first place, and it is expected that the Anodized will surely peel off sooner or later.
I would probably be happier if they were more rugged and a little less expensive.
How was your experience with it?
Can also be used with JC92.
I have included a photo, but it is exquisitely designed to avoid horn Horn, etc.
The quintessence is an exclusive product.
I used it to remove the Front fork and it worked normally.
However, if the Mini stand is not used, it will be Lifted up quite a bit.
Rear stands are also not recommended, as I think they are quite dangerous unless you use one that rises reasonably high.
It makes sense that a product called Mini stand is properly prepared.
[Points to note]
Type of STAND to be used.
Note that if the Mini stand is not used, the Lift up height will be great.
Also, if Mini stand is not used, it is a little difficult to insert the Adapter into the Stem hole first.
Fortunately, the GROM is a lightweight vehicle, so we lifted the body of the vehicle by hand and forced it in.
How did it compare to other products?
No comparable product as it is an exclusive product.
View detail
![[Repair/Option Parts]Repair item Adapter for Front stand2](https://img.webike-cdn.net/catalogue/images/96580/25298_TS.jpg)
Just the right size feeling
The color of J-Trip's front stand is 19mm and I wanted 20mm or 21mm.
It worked perfectly and now it will Lift with Swizzerland!
Used on a YamahaFZr1000 with a 91 inverted 3GM
View detail
Fits: DUCATI panigale, DUCATI panigale, DUCATI panigale
Also available in 2021 V4
[How is it used?
Used in 2021 Panigale V4 SP.
The STAND side uses J-TRIP's Front stand.
Was the one you received as per Image?
Yes.
I had also bought another boss for GROM, both of which were Gold alumite processed.
Since the Motorcycle and GunGun rub against each other, I think it will eventually peel off even if it is anodized nicely.
I think it should be more martial…
Is this the reason for the SPECIAL Knife?
How was your experience with it?
First of all, you didn't mention what year it is compatible with, but it is also usable with the 2021 Panigale.
If the Universal boss is left in place, the vehicle body and STAND will hit each other.
I know there is a way to lift up the bottom of the front fork, but I wanted to use the front stand because I was afraid of attaching and detaching the wheel, and also because I thought it would put too much load on the front fork.
Being a dedicated product, there are no problems at all with accuracy or usability.
Just overpriced…
[Points to note]
The front stand cannot be used on Panigale unless the stem hole is removed, because the stem hole is still blocked.
Let's remove the StemHole cap. (I removed it by poking it from the Top Bridge side.)
How did it compare to other products?
Fork up stand was considered, although I don't have one to compare it to because it is a dedicated product.
However, I really wanted to use the front stand that I have now, because it is difficult to find a place to put it when it is covered with STAND.
View detail
It's solid.
It is indeed a Manufacturer's product! I use it with peace of mind. View detail
Excellent stability
Purchased in conjunction with J-TRIPShort lowlerRear stand
Stand Hook is already pre-installed.
It's a V receiver, so it's very stable.
View detail