Reviews
Fits: KAWASAKI Ninja 1000SX, KAWASAKI Ninja 1000 (Z1000SX)
OEM is good, but? .......
I bought it for my Ninja 1000, and installation is an easy job that can be done in 20 seconds or less, right?
As expected of OEMParts, quality is guaranteed!
However, considering the prevention of scratches when standing up and falling down, I thought the cover area was too small.
View detail
Fits: KAWASAKI Ninja 1000SX, KAWASAKI Ninja 1000 (Z1000SX)
Crankcase Ring
I purchased this product because it is an OEM Product.
I thought Kawasaki's Logo was cool.
It is a bit pricey, but it seems to protect you if you fall to your feet.
Nevertheless, theQuantity:Pair (for Left and Right) It is
Just peel and stick the double-sided tape, so Quantity:Pair (for Left and Right) If you don't make a mistake, anyone can do it on their own.
View detail
Fits: KAWASAKI Ninja 1000SX, KAWASAKI Ninja 1000 (Z1000SX)
Design Fine
It looks cool! The kawasakiLogo stands out just right without being too far forward. It's a little expensive, but I'm glad I bought it. View detail
Fits: KAWASAKI Ninja 1000SX, KAWASAKI Ninja 1000 (Z1000SX)
Design Fine
I think it's effective for standing up, and it fits well with the body because it's well-designed and OEM.
It is a good quality and works well. It has a good texture and does not require a work kill, but the drawback is that it is not cosmetically pleasing.
View detail
Fits: KAWASAKI Ninja 1000SX, KAWASAKI Ninja 1000 (Z1000SX)
The defenses are...
I don't know, as I haven't mocked it up yet, but it seems to have low protection. However, it has more of a dress-up effect.:Pair (for Left and Right) Both are with Logo of KAWASAKI. View detail
Fits: KAWASAKI Ninja 1000SX, KAWASAKI Ninja 1000 (Z1000SX)
I wouldn't want to repurchase if I could help it.
I had purchased it thinking I would do it at some point, but the time finally came to use it.
I thought it would be easy, but the Double-sided tape was strong and quite Large strange to remove. It was easy to install once it was removed.
View detail
Fits: KAWASAKI Ninja 1000SX, KAWASAKI Ninja 1000 (Z1000SX)
I don't want to buy Repeat anymore (lol).
In fact, after installation, I was embarrassed to say that it was a standing failure (and Quantity).:Pair (for Left and Right) I did (one at a time too) and this is the Review afterwards.
It wasn't a large impact because it was a standing mishap, but the Left Side Cover was well scratched, but the Crankcase was intact. I had OEM Slider and Slider was also scratched, but Cowl was not scratched.
He did his job well.
But even though it's a Cover, I didn't want to ride with the scratches, so I bought the same one and replaced it.
I thought that it was a little high that it cost more than 7000 yen with this, but I think that it will cost tens of thousands of yen when I change CrankcaseBody, so it is good.
It's made of plastic and it's only held together with double-sided tape, so I had my doubts about whether the crankcase would be protected in case of a violent fall while driving, but when I removed it, I felt that the double-sided tape was surprisingly strong and would not come off even if I pulled on it. I had to use Parts cleaner and SealRemover to get it off.
It's going to protect you until you fall over and the Plastic gets scraped off.
View detail
Fits: KAWASAKI Ninja 1000SX, KAWASAKI Ninja 1000 (Z1000SX)
I installed it to hide the scratches.
I bought this to cover up the damage I did to my Crankcase last time I had a bad fall. It's made of plastic with double-sided tape, so I'm not sure if it will protect my crankcase if I take a nasty fall while riding, but I think it will lessen the impact more than not.
Plastic, but the texture is not bad.
To install, just degrease with parts cleaner and peel off the double-sided tape and fasten. I used a maintenance stand to set it up horizontally, but I think a side stand would have worked just as well, but I thought it would have been easier to set it up straighter since it's pretty low down.
View detail
Fits: KAWASAKI Ninja 1000SX, KAWASAKI Ninja 1000 (Z1000SX)
Will it only end up being expensive?
Material:It's plastic and double-sided tape, and when you touch it, it feels fluffy It is
It's expensive
I put it on in the OP when the car was new, but the reason was that the clerk recommended I put it on
Even with the Frame Slider on this motorcycle, if you take it down, you can get a Crankcase It's because it's going to get done There is no sense of being an afterthought
That's why I try to think of it as a deliberate attempt to make it cushiony and easy to replace I am
I haven't taken it down yet, so... how do I know if I've been tricked?
View detail
Fits: KAWASAKI Ninja 1000SX, KAWASAKI Ninja 1000 (Z1000SX)
Plastic board
It was just a simple thing to attach a plastic board with double-sided tape other (esp. people)
Also, it is not a complete protection against the Crankcase in the event of a motorcycle collapse (after the -te form of a verb) not ..
And this price is too high for that
View detail