Reviews
Fits: その他 TMR Carburetor Big Body Φ36-Φ41 / Small Body Φ28-Φ35
Reliable OEM Product
In use at SRV 250, it will not appear on Yamaha OEM, but here is OEM Product purchase from Mikuni. I can use Air Screw without problem. View detail
Fits: その他 TMR Carburetor Big Body Φ36-Φ41 / Small Body Φ28-Φ35
TMX 30 Starter O-ring ...
I attach 1 KT CableChalk to MikuniTMX 30 Carburetor. Since the O-ring of the Starter part is not a single body, if I was looking for it, I found a nice O-ring and I tried it. The inner diameter of the groove of the Starter is 11 mm, the O-ring is about 10 mm and it is Small Shime, but it was just fine.
View detail
It certainly changed!
After second-hand TMR purchase it was dense at all openings so I bought Needle's Straight and Taper, I bought it dense ~. As you observed the Jet needle that was originally attached, it seemed like NYLLE JET wears out as it was a feeling that the straight portion is worn, so as expected and it was not changed so much with the new P-6 Purchase P-4. P - 6 After changing engine, if I put Engine on, it got thinner now, if I make Straight thinner the first time the air / fuel ratio becomes 14. 5th to 13th. Idling also changed to 11. 6th to 12th. Because it became 4th place, the effect is perfect! Needle Jet also wears out, so if you are getting sick, you may just switch to a new one, it's just expensive! View detail
I am indebted to you every time.
In my case, because it is a special engine, it is ineffective at Size which I sell at a mass merchandise store
I am using Webike to buy Jet classes..
Previously, Setting was not available if you were using Main jet of a certain Manufacturer
When I changed to MikuniOEM, I heard stories about Setting,
Jet class decided to buy Mikuni OEM.
If you ask me to say your own self, you can stock more than 4 Size each and you will complain!
View detail
Fits: その他 TMR Carburetor Big Body Φ36-Φ41 / Small Body Φ28-Φ35
I am saved.
It is very helpful to have inventory of these consumables.
Especially repair O-ring etc - Because I can not repair, I always want to keep it constantly,
Since I would like to purchase it for other shopping, it is a small part, but I can trust ManufacturerOEM Product
I hope Webike also does not cut stocks.
View detail
Manufacturer thing
Manufacturer thing, so I trust it and purchase it. I am not worried about anything.
Mikuni's circle Main jet.
It is Fu Two.
I think that Mikuni will give out the shape of the main jet like the Bomb kit.
View detail
Cheap?
It seems that it was cheaper than ordering with vehicle OEM Product.
Wonder if it is supposed to be the same Parts?
Because it is a Manufacturer thing, I think that the construction is the same ...
View detail
it fit to spec and quality good. use for carb xjr1300 year 1999 . easy to setup and tune for engine. if you want pilot jet for carb use this.
it fit to spec and quality good. use for carb xjr1300 year 1999 . easy to setup and tune for engine. if you want pilot jet for carb use this. View detail
Fits: その他 TMR Carburetor Big Body Φ36-Φ41 / Small Body Φ28-Φ35
Ideal as reserve
It's not something so painful, but as Needle changes are setting
Exchanges etc at the destination etc.. Because there is also things to do. Small parts of this stuff rolling as they are removed on the road
First not found... (Lol) I have it as a reserve for such a time.
As performance and making, it is a part made by Mikuni used for Mikuni carburetor, so there is no problem.
Although it might be expensive if Cost-like things like Washer are considered
Still, since you can buy four of Multi for hundreds of yen, those who can boost Setting yourself
I think that there is no loss by buying it for the time of emergency.
It is different from the product imprint, but the large part (Expensive parts) etc. I'm surprisingly a thing to be managed at the shop, so I am not in trouble so much, but I looked around the shop to buy such parts of hundreds of yen tens of yen more than anything
I will order even more after all, go to pick up later etc etc etc. , In the past it was tedious, but you can buy it immediately with Net
WEBIKE 's Lineup is very appreciated.
View detail
Fits: その他 TMR Carburetor Big Body Φ36-Φ41 / Small Body Φ28-Φ35
As a reserve
It's not something so painful, but as Needle changes are setting
Exchanges etc at the destination etc.. Because there is also things to do. Small parts of this stuff rolling as they are removed on the road
First not found... (Lol) I have it as a reserve for such a time.
As performance and making, it is a part made by Mikuni used for Mikuni carburetor, so there is no problem.
Although it might be expensive if Cost-like things like Washer are considered
Still, since you can buy four of Multi for hundreds of yen, those who can boost Setting yourself
I think that there is no loss by buying it for the time of emergency.
It is different from the product imprint, but the large part (Expensive parts) etc. I'm surprisingly a thing to be managed at the shop, so I am not in trouble so much, but I looked around the shop to buy such parts of hundreds of yen tens of yen more than anything
I will order even more after all, go to pick up later etc etc etc. , In the past it was tedious, but you can buy it immediately with Net
WEBIKE 's Lineup is very appreciated.
View detail
Since it is a Setting part, it is not possible and it is impossible.
It is used in TMR32.
It is hard to see the count recently with the naked eye, I did not feel that it is particularly hard to see because everyone sees it with Loupe.
Although it is unavoidable that the price will increase if you arrange with the dust as well as the dust, I think that it is necessary expenses if it thinks to give Damage to the Engine itself by popping.
View detail
Fits: その他 TDMR Carburetor for Φ40, その他 For TMR carburetor Φ40
Product making was a good thing.
It is unfortunate to make it that you can hardly see if you put Filter on Aluminum's Cut-out.
I think that compatibility with DNAFilter does not come off just by slightly tightening the Band when wearing a large amount of change.
View detail
Fits: その他 TMR Carburetor for Small Body (Φ28-Φ35), その他 TDMR Carburetor for Small Body (Φ28-Φ35)
Reliable OEM?
Since TMR, Mikuni = Ichimi OEM Parts Number I think that accuracy is not a problem as well.
Although there is no problem if looking at parts only - - - To be precise, if you compare it with FCR Carburetor Body, the type of Needle is the first few.
Even if you just change the Straight diameter first, the Setting changes to Large width.
It is a feeling that I want Lineup in the middle. (NeedleZone partial and about 2 with air-fuel ratio meter. 0 also changes)
Furthermore, since the width of Clip change is also wider than FCR Carburetor Body, changing it one step will make it change too much.
TMR is not limited only to Needle, because Overlap other than MJ feels Large
Change Theed system Needle change (Or vice versa) I suppose it would be said that the price should be cheaper a little more - - -
Well, as long as it does not concern up to that, it runs to a certain extent so even if the price sticks to Setting, the middle lineup is a place I want.
View detail
With TMR setting
It is used in TMR32.
Eyes are getting older so that the counts all want Loupe
I did not feel that it is particularly hard to see.
Although it is unavoidable that the price will increase if you arrange with the dust as well as the dust, I think that it is necessary expenses if it thinks to give Damage to the Engine itself by popping.
View detail
Fits: その他 TMR Carburetor Big Body Φ36-Φ41 / Small Body Φ28-Φ35
Variety at Setting ,,,
When turning on or off setting
You had better buy it.
It may be said to the whole of the recent Rubber
I feel something is wrong ...
There is a thing that comes back with a couple of Rose shies when luck is bad.
Especially since Mikuni's instructions are also ordered to use a special carburetor chestnut (Although it says, the basic carburetor chestnut is not put on the Rubber part, but haha) I feel a little weak.
Just Webike who can prepare such a detailed part immediately is awesome.
View detail
Finally found out
I used it for Setting of VIRAGO.
To the nearby appliance store there is a tip 2. I put only 5 mm of things, I cut it old Jet and used it on my own making, so it was somewhat uneasy.
With this, I will challenge Long touring with confidence.
View detail
Fits: その他 TM(RS) carburetor for multi/big body φ36/φ38/φ40
I overhaul in Overflow.
I had a hard time pulling out Float's pin, but it was a great change to Large.
It is appreciated that the Pilot screw is also included (^^) /
Unfortunately, since the Float chamber O - ring sucked Gasoline and it stretched out, it seemed unlikely to be used until returning, so the O - ring Float chamber is now Quantity : 1 Set Yes, it will be appreciated. F (^ _ ^;
View detail
20 years air-cooled car
I exchanged the Main jet as it was at the time of the new car as a part of Carburetor 's Overhaul.
As the Plug was in a CUB taste, I tried to replace the aged deterioration of Main jet with suspicion.
Engine startability has improved. Plug is also normal burning condition. Due to aged deterioration and repeated repeated wearing, frequent use of Carburetor cleaner I thought that the old Main jet was getting a little hole large enough?. (It is a personal opinion to the last. There is no confirmation because it is a precision part)
The price is also cheap, and we recommend purchasing Jet of ManufacturerOEM along with Overhaul of Carburetor.
View detail
Fits: その他 TDMR Carburetor for Large Body (Φ36-Φ41), その他 TMR Carburetor for Large Body (Φ36-Φ41)
Necessary for Carburetor setting
Because we stock various Jet classes at Carburetor setting
Large I am strangely saved..
I will continue to use it.
If you want greed, I wish you a little more inventory.
View detail
Fits: その他 TMR Carburetor Big Body 77-85-77 Pitch / 77-93-77 Pitch / Small Body 77-85-77 Pitch
After all MikuniOEM
Carburetor's O / It was over at the time of H, O / I was in H, so I had to order in a hurry.
Mr. webike confirms that there is inventory and orders without hesitation.
The next day we received it at hand and succeeded O / H is completed and relieved.
I attempted to divert Fuel Hose resistant to diameter,
I chose Mikuni OEM again.
Compared to Universal's Hose, the price is higher, but it is cheap if you think that you buy relief.
View detail