Reviews
It was helpful
It's easy to grip and grips the piston well. It's so easy to use that I don't think I'll need to use the Fixing Screw.Recommendation. View detail
I should have bought it earlier without being stingy. The price is still a barrier.
Purchased to clean my Caliper piston.
I was hesitant to buy it at first, and when I put Dustcloth on Piston and sandwiched it with ViseClip, I got a scratch.
You can't be stingy in the weirdest places.
View detail
Doesn't hurt my hands.
The grip is soft so it doesn't hurt my hands when I work with it. I didn't get tired even in long work. View detail
Lock Function is very useful!
The night of 15 when I thought that all Piston Extractors were the same.
Piston polish that was convenient to use the lock mechanism this time
BlueMagic is seriously awesome!
Well, what I'm trying to say is, congratulations on your marriage, Gacky!
View detail
It is convenient to use differently.
The included two plates can be swapped to accommodate various types of brake calipers for efficient use, and the Pistons can be easily pushed in and out of the Caliper and Pistons without straining the Caliper or Pistons. View detail
If it's not stuck, it's not stuck;
It is not possible to hold the piston with grip strength alone when removing a stuck piston.
Even if you wrap Towel around it, your hands will hurt.
You might like Stopper included. which is a little above Class.
I turned the Pliers upright and stepped on them with my foot to remove the grit.
For turning Pistons when cleaning.
View detail
Wound goes into Piston.
Used for Caliper piston rub.
It is impossible to pull out the piston without this, unless the piston is in a good mood right after assembly.
There was no hesitation in using it, and it was strong enough to be used for a 250cc single push Single.
The drawback is that the lock to keep the tool open is applied by itself when you notice it, and Stress may boil. It's not a fatal problem, but the Lock Function is not really needed.
In addition, because the edge of the tool bites into the inside of the piston structurally, the piston will be scratched to a small extent. This is unavoidable, but if you are a nervous worker, you must take measures such as biting the Dustcloth.
View detail
Can be used without problems
Function and workability are fine, but
The part that suppresses Piston is Knurl by the genus Gold, so it scratches the inside of Piston.
If you are worried about it, you need to take measures such as putting Dustcloth in between.
View detail
It works perfectly fine.
I bought this because I was going to replace the Brake Pads myself and I wanted to clean the Piston.
I wasn't sure if I could rotate it properly because the part that grips the Piston is made of Gold, but no problem at all!
I was able to polish the Piston without much grip strength.
A must for anyone who cleans their own Brake Calipers or rubs out their Pistons!
View detail
Very practical
The caliper piston of a motorcycle needs regular maintenance. During maintenance, this tool from Daytona plays a very important role. Add the pistons together and rotate, and it is easy to clean the back of the piston. Very convenient. ---------------------------------------------- Motorcycle piston calipers have to do maintenance on a regular basis. Maintenance time, DAYTONA This tool will play a significant role. The combined rotation of the piston, the piston is easy to put to the back surface cleaning. Very convenient. Powered by Google Translator View detail
Front caliper is fine! Rear caliper...?
It was useful for Front caliper Piston.......................... View detail
If you're a motorcycle that's regularly serviced, you'll be able to
Cost performance is good
Although it can be used with no problem in Brake which is usually maintained small and diligent, it cannot grasp Piston firmly and slips when movement is reluctant without touching it for a long time.
View detail
Takes some getting used to?
I tried to replace Seal because I removed the Caliper, but it was on the way. "Oh, that's easy! . But I couldn't pull out the whole thing because I couldn't spread it out and lift it up. View detail
Four Wheels for VehicleSpec.
When I inserted it into the Caliper of the two-wheeler, it went in to the tip, but not the whole surface. (There are pictures.)
I turned the Handlebar from there, but it takes a lot of force.
It was difficult to work with the Caliper hanging, so I removed the Caliper from the body.
View detail
Convenient for pad replacement.
The Brake Caliper Pistons are easily pushed back in to replace the Brake Pads, which is less scratchy and more efficient than using Pliers to replace them. View detail
Don't fuck with the customers.
I would never buy from this company, even if they are the only Manufacturer in the world. The customer service is arrogant and offensive. The corporate attitude is to be expected.
It's a local business and I want it to go away.
I would definitely not recommend it to everyone considering it.
View detail
Pad replacement is easy.
It can be used with various types of Brake Calipers to help with pad changes, and it can also be used with 2-pod Calipers to reduce the amount of time it takes to push the Piston in one go. View detail
sufficient for one's needs
This is a necessity when you fail to rub out a Piston or overhaul a used Caliper with a Single Body.
Because the part that hits the inside of the piston is the iron of GizaGiza, there are some scratches on the surface of the piston, but it does not affect the performance of Piston, and if it can be pulled out by one shot, it is only a small scratch, so I think it is necessary and sufficient performance.
View detail
It can be used normally
There is not much in the way of luxury or design in terms of appearance.
It has been stored in an indoor toolbox and has not rusted for 8 years.
The Grip is thin and painful for a tool that requires a lot of force to use. However, you can turn the Piston with the grip strength of an average man, if it doesn't stick, you can do your best.
Also, I've never felt the need for the Butterfly Screw when using it.
The butterfly screw is used to make it close in Small size when storing. The width is about 43mm up and down without the butterfly screw.
Material is a material that sticks to magnets, so we use separately purchased magnetic holders for storage.
View detail
Two (or three) axes are better
I've been using products with a single-core shaft guide
The structure is severely twisted, limiting its use
I think this product is good for GJ in that regard
View detail