Reviews
Convenient to install Disc Lock on the vehicle without burden to the body.
I would like to carry a Disc Lock with Alarm to protect against theft while on the road, but I don't want to carry it in my backpack or HolsterBack because the Disc Lock is so heavy.
Also, since I ride a naked motorcycle and did not want to use a Seat bag or Tank Bag just for this purpose, I chose this Holder which allows me to secure the Disc Lock to the vehicle body.
This Holder is designed to be attached to the Handlebar, but I didn't want to make too much noise by attaching this and that around the Handlebar, so I attached it to the Tandem FootpegBracket.
I am satisfied with the ease of use.
View detail
Fits: HONDA CBX125F, HONDA NSR250R, HONDA CBR250R, HONDA VFR400R, HONDA Integra, HONDA CBR400R, HONDA SUPER BOLDOR, HONDA CBR300R, HONDA RVF400, HONDA CB400SB, YAMAHA TZM50R, YAMAHA YZF-R125, YAMAHA TZR250, YAMAHA YZF-R15, YAMAHA YZF-R25, YAMAHA FAZER, YAMAHA FZR400RR, YAMAHA YZF-R3, YAMAHA YZF-R6, YAMAHA XJ6
First MirrorBlinker installation
I put it on a yzf-25r early model.
Screw holes don't meet at all, so I have to rebuild them.
It must not be done. It is absolutely impossible for an amateur.
View detail
Inexpensive but effective parts
The fastening Bolt of BMWOEMBrake Caliper was rusting, so I replaced it with Titaniumium Bolt from Rise Corporation during Overhaul.
A certain Oak Auction has a Bolt made of SUS304 Stainless Steel for Caliper fastening, but considering the fracture strength of the material, I think it is very dangerous and has a high possibility of breakage.
This Titaniumium bolt should have no problem in terms of strength, and the screw threads are beautifully machined.
View detail
For retrofitting electrical systems
I purchased the Racer to make it a public road Spec.
Quantity of electrical components:I could have bought it as a Set, but I bought this one because I can reconfigure it in various ways.
It was a little bit difficult to wire the unit because it was installed from scratch in a vehicle with no safety components. 6V MONKEY/GORILLA Main Harness is connected to the main harness, which switches the supply from the power source on and off.
View detail
Fits: HONDA APE, HONDA BENLY50, HONDA DAX, HONDA MONKEY, HONDA CT110 HUNTER CUB, HONDA GB250 CLUBMAN, HONDA FTR223, HONDA CL400, HONDA FTR220, YAMAHA SRV250, YAMAHA RENAISSA, YAMAHA BRONCO, YAMAHA TW225, YAMAHA TW200, YAMAHA SR400, YAMAHA SR500, SUZUKI VANVAN, SUZUKI GN125, SUZUKI GS125, SUZUKI VOLTY
Blinker replacement
Replacement was easy, but the Valve needed to be replaced because it was a high flasher. View detail
Addressv125Seat
The Seat I received is torn and I want to return it.
I had to delete the order screen when I received the item and
And that it's an unused number to call.
I could have emailed her, but she wanted a picture of me.
They said they shipped a torn Seat and if you want to return it, you have to pay in advance.
When you send a damaged item, you pay cash on delivery, right?
In the first place, it was not an expensive item, so I thought I would pay in advance.
It makes no sense because it would be an expensive product. 。
Why should our side have to go that far?
The system is difficult to return.
I still use this Shop only for buying OEM Parts.
View detail
Fits: HONDA FUSION [Fusion]., HONDA FUSION SE, HONDA FUSION X, HONDA FUSION [Fusion] XX, HONDA FUSION [Fusion]., HONDA FUSION SE, HONDA FUSION X, HONDA FUSION [Fusion] XX
most parts dont fit
The undercowl fenders do not fit without any custom fabrication, i had to use a dremel to make some parts fit. And one fender peice came with broken plastic. Would NOT recommend. View detail
Fits: HONDA FUSION [Fusion](MF02), HONDA FUSION [Fusion](MF02)
looks great
Looks great and definitely made my instrument cluster look alot better. Just unfortunate theres no official way to put in the Honda Helix logos into that aftermarket cover. But otherwise looks good View detail
Fits: Others , HONDA glom, HONDA CB125R, HONDA XR230, HONDA XR250MOTARD, HONDA VTR250, HONDA NIGHTHAWK250, HONDA VT250 SPADA, HONDA CB250F, HONDA CB250R, HONDA CRM250AR, HONDA CRF250RALLY50, HONDA CRF300L, HONDA CB400F, HONDA CB400SF, HONDA 400X, HONDA NC700S, HONDA NC700X, HONDA PCX, HONDA FUSION
CB250R installed.
I installed it on my CB250R. Affordable and easy to see.
It's just right because it doesn't stick in the Motorcycle seat.
View detail
Very Nice!
Awesome exhaust great prices and super fast shipping. The workmanship is incredible can't wait to install it on my Honda reflex scooter it is still winter where I live but I will install it asap! Thank you so much! Gerry View detail
Fits: SUZUKI VANVAN200, SUZUKI GSX-S125, SUZUKI GSX-R1000R, HONDA APE 50, HONDA DIO110, HONDA BENLY50, HONDA BENLY50110 PRO, HONDA BENLY50110, HONDA BENLY50 PRO, HONDA APE 100, SUZUKI GSX-R1000, SUZUKI BURGMAN200, YAMAHA MT-25, YAMAHA MT-07, YAMAHA MT-03, YAMAHA MAJESTYS, YAMAHA CYGNUS 125, YAMAHA CYGNUS X, HONDA APE TypeD
What a quality!
It is subtle in terms of Size.
I think the normal use is to use Side Stand with Handlebar Lock.
Sexy as in the picture, your legs are visible. I wanted it to be just a little bit longer.
Also, the bottom belt broke off after 3 days of use. What kind of quality is this?
The motive for purchasing the product was not only the price, but also the fact that it was written as heat-resistant, so I focused on the fact that I could apply it immediately after returning home, but Belt may have melted due to the heat from the Exhaust System.
As for the Cover, it is Black and has the word Security on it, so it is concealed for the purpose of minimum security. So, Belt is very disappointing because it is Clear.
I honestly want to return it.
View detail
For a little peace of mind when getting off the train.
I think it's just right for Appeal.
As expected, I am hesitant to use it for extended parking at home because I am afraid of Brake sticking to it. I use it only for going out.
View detail
Ideal for washing a wide range of cars!
I bought this Large sponge type product because my car is a Full Cowl and I need to polish a large area! Bubbling." Water absorbency." The concave center section makes it easy to grip!" It is impeccable! I have used it over 30 times to wash my car and it has never lost its shape! It can be used hard! View detail
Fits: Others
You can get the feeling of doing it even with such small parts.
Pad pin of bremboOEM is a little Large strange to remove! View detail
Requires some ingenuity in installation
Quantity:Pair (for Left and Right) The end cap of the grip can be removed by pushing it out from the inside (not by screwing it on), but it is difficult to remove if it is stuck in the grip rubber well.
As others have mentioned, the wire winding diameter of the Throttle cone is about 2mm smaller than OEM, so that part needs to be modified.
I had originally cut and modified PVC Pipe to make it larger in diameter, so I did the same with this one.
The diameter of the part where the Grip Rubber is attached is the same as that of a normal Throttle cone, so it can be used without modification if there is no problem with the Throttle cone being low-slung.
The Left Side Grip was also press-fitted with a Throttle cone, so I was worried about installation, but this one had rubber on the inside of the cone, so it fit the outside diameter of the Millibar as it was, so after peeling off the original Grip Rubber, I lightly tapped it in and it went in. After peeling off the original Grip Rubber, I lightly tapped it in and it went in.
For the power supply, there was an Emon power supply extraction fuse of the same size as the Headlight fuse, so the Cable end of this fuse and the Wiring end on the Heater side were each modified and attached to the Bullet Terminal.
There was no place to install the minus ground, but a regulated rectifier was installed in the front cover, and its mounting bracket was a bare gold plate, so I loosened the bolt there and connected the wiring between the plate and the plate. The bracket was a bare Gold plate, so I loosened the Bolt there and connected the Wiring between the plates.
When the power is supplied properly, the Button glows Red→Green→Blue, so it was also convenient for installation to check whether ACC is energized or not.
The color of the Switch's Lamp is probably set to Red (strong), Green (medium), and Blue (weak) like many other things, but when I ran a test run, I felt that Blue was warmer than Green.
I am satisfied with the Switch as it is easy to operate and has a good texture.
Other reviews said the color of the Switch was Orange, but the one we received was Black.
I honestly did not expect it to be this good from the Body price, so I was disappointed in a good way.
I wish I had purchased it earlier.
View detail
Fits: HONDA CBX125F, HONDA NSR250R, HONDA CBR250R, HONDA VFR400R, HONDA Integra, HONDA CBR400R, HONDA SUPER BOLDOR, HONDA CBR300R, HONDA RVF400, HONDA CB400SB, YAMAHA TZM50R, YAMAHA YZF-R125, YAMAHA TZR250, YAMAHA YZF-R15, YAMAHA YZF-R25, YAMAHA FAZER, YAMAHA FZR400RR, YAMAHA YZF-R3, YAMAHA YZF-R6, YAMAHA XJ6
Installed on yzf-r15 India Spec. 2013 Not very satisfied
The included rubber cap was not usable because it was a size larger than Mirror.
There was not enough room in the loops of the mounting holes, and the Left Mirror was easily attached, but the Right Mirror was attached by brute force.
The Mirror in its packaging was facing the opposite way, so it could not easily be turned 180 degrees when trying to turn it.
Visibility is good.
View detail
Fits: KAWASAKI Z400, KAWASAKI Z400, KAWASAKI Z400, KAWASAKI W650 EJ650A, KAWASAKI KZ400, KAWASAKI EX500S, KAWASAKI ESTRELLA [ESTRELLA] RS Custom BJ250A, KAWASAKI ESTRELLA Custom BJ250A, KAWASAKI ESTRELLA [Estrella] BJ250A, KAWASAKI ELIMINATOR250 [ELIMINATOR]SE EL250A, KAWASAKI ELIMINATOR250 [ELIMINATOR] V VN250A, KAWASAKI 250TR BJ250F, KAWASAKI 250TR BJ250F, KAWASAKI Z400LTD Belt Drive KZ400H 83, KAWASAKI Z250LTD Belt Drive KZ250R 83-87, KAWASAKI W650 EJ650A 05-08, KAWASAKI KZ440Sport Belt 82, KAWASAKI KZ440LTD Series 83, KAWASAKI KZ440LTD Series 80-82, KAWASAKI KZ440LTD Belt 83
The best!
It is perfect. I contacted Webig first and received an immediate response. It is not easy for me to ask myself, "Will this product be compatible? I am very relieved because I asked Webig about it before purchasing. The product is as good as OEM. I am not sure about the durability of the product yet, but the low price and quick shipping was a big help. I will continue to use your company for many years to come. View detail
Fits: SUZUKI DESPELADO, SUZUKI BOULEVARD, SUZUKI MARAUDER, SUZUKI VANVAN, SUZUKI TEMPTER, SUZUKI INTRUDER, YAMAHA Ensiter 125, SUZUKI SAVAGE, YAMAHA FZX750, YAMAHA XV950, YAMAHA R100 ROADSTER, YAMAHA VIRAGO, YAMAHA XV1900, YAMAHA DRUG STAR, YAMAHA Bolt, YAMAHA SR400, YAMAHA SR500, HONDA CTX700N, HONDA CB650, HONDA DREAM
Good cost performance for the production
I think the quality is high for the low price.
The body is a rather heavy gold, and the lens cut is a bit stylish.
I think that the cosmetics of inexpensiveness in relation to price is the strongest.
View detail
Fits: KAWASAKI NINJA2 Helmet50RR, HONDA CB223S, HONDA CB400SF, HONDA GB250 CLUBMAN, KAWASAKI KSR-1, KAWASAKI KSR-2, KAWASAKI ZX-10R, KAWASAKI ZX-6R, KAWASAKI ZX-9R, KAWASAKI ZZR1100/ZX-11, KAWASAKI NINJA400R (-2013), SUZUKI GSX1100S KATANA (KATANA), SUZUKI GSX250S KATANA, SUZUKI GSX400S KATANA, SUZUKI GSX750 KATANA, SUZUKI GSX-R1000, SUZUKI GSX-R400, SUZUKI GSX-R600, SUZUKI GSX-R750, YAMAHA R1-Z
Cospar good
First of all, the cosmetics are good. I have no problem with it. I thought it was a very kind construction with markings to guide the positioning when installing it, but I do not recommend it to those who are concerned about markings. View detail
Fits: Others , HONDA glom, HONDA CB125R, HONDA XR230, HONDA XR250MOTARD, HONDA VTR250, HONDA NIGHTHAWK250, HONDA VT250 SPADA, HONDA CB250F, HONDA CB250R, HONDA CRM250AR, HONDA CRF250RALLY50, HONDA CRF300L, HONDA CB400F, HONDA CB400SF, HONDA 400X, HONDA NC700S, HONDA NC700X, HONDA PCX, HONDA FUSION
quite good shape
Mirror was rusted out and replaced with a more recent form.
The navigation is easy to see and the design of the Mirror makes the vehicle feel like it has been exposed.
There is no runout when driving.
View detail