Reviews
Helpful for error correction
These parts are appropriate for compensating for speed errors caused by changes in the number of sprocket pins or tire size.
The system was usable with simple installation.
View detail
Helpful for error correction
Parts that should be in the correction of speed display errors due to changes in Sprocket's Ding number and Tire size.
Installation, adjustment, etc. was easy.
View detail
Installed on yzfr25 2019 MODEL
FrontSprocket was changed to 13 guns and installed.
In the Installation Instruction Manual, I think it is an explanation of the previous MODEL.
It is like interrupting the Coupler of Rear brake and Speed sensor.
The Rear brake side is a little different from the picture, but easier to Access.
On the speed sensor side, the side cowl must be removed.
Access is not available.
Remove the SIDEInner cover and remove the Blinker wire before
Remove the Side cowl.
Connectors are also difficult to remove, so some ingenuity is required.
I made a mistake in my settings and got a ridiculous display.
It has been fixed and is working properly.
Tire size is set as a percentage in the settings.
It was set at Tire size 140 ^^;
You might want to look on you tube for instructions on how to set it up ^^;
View detail
You can use it to correct Meter.
I use it when I change the Sprocket on my Grom and when I change the Tire.
It is possible to make the speed almost actual measurement if the value of Tire is fine-tuned while watching GPS of the smartphone.
If you don't like HappyMeter, here you go.
View detail
Initial failure
All Rear SprocketPlus settings could not be done
Perhaps RearLarge Do you think that there is no one to distress?
It can be confirmed only after connecting and there is no guarantee effect
It's my middle finger.
View detail
Required Items after Sprocket exchange
It installed according to exchange of FrontSprocket.
Installation will end in about 30 minutes including setting.
Special Tools etc is not necessary,
We need to remove Left Side Cover.
Also, when removing Connector of Crankcase part,
Since there is a possibility that the hand does not enter the gap when the hand is large,
It will be easier to use Precision Driver etc..
Since Body is Small, it fits well in Space under Seat.
Bundle Wiring to Frame next to Fuel Pump,
Body fixed on ECU with Double-sided Tape.
By changing FrontSprocket from OEM 14 T to 15 T,
Although I felt that the speed was increasingly sensed,
It was suspicious because it was not changed by Meter reading.
Thanks to this Parts Meter speed has been corrected,
A proper speed is now displayed.
Although there is no schedule of Tire exchange at present,
Even when exchanging later, speed correction
I thought it was parts to be indebted.
Although it is a difficult point that the price is high,
For people riding by customizing Z125
I'd like to recommend Parts.
View detail
To speed management
I purchased it because I changed the number of Front sprocket.
It seems that setting is very easy and speed is displayed correctly.
Also, it is ◎ that it corresponds to the change of Tire size.
It is troublesome to open the lid with + Driver to Access to the setting Button, so I think that it was good if it was a little more simple method.
View detail
Meter correction
Recent cars and Motorcycle speedometers that are being corrected so that faster speeds are coming out than in the past.
Purchase this product to display this accurately.
The position of the Coupler for making the product to be Bypassed at the time of installation was immediately found by the Instruction Manual, but it did not have enough space and it fits quite a bit
I struggled to connect.
Recommendation to disconnect Couplers once and then connect them.
Personal Data
The correction item is the outer circumference Length of FSprocket, RSprocket, Rear tire, but I set the Rear tire circumference Length setting value to 90%.
With this, NORMAL's 2014 MODEL's MC 41 has become fairly accurate speed display.
By the way, I checked the speed with GPS.
Conversion Unit Body Installation position is placed in the picture with Cushion Tape wrapped in GRUGRU.
View detail
Meter error corrected!
Changing Sprocket of Front to Small diameter, Meter error was too large Large, so buy this item.
The Instruction Manual was well written about the setting, but I got a bit of trouble finding Connector. It was hard to remove Cowl next to EngineLeft.
After installation, I checked it with GPSNavigation but I think that it shows almost the proper value.
Can I make it a little cheaper?
View detail