Reviews
We used it for Hazard switch!
The other item of the same brand, the Blinker relay with Hazard switch function, is under the Seat, and from there the Wiring for the switch is extended to the switch part on the Axel side, but the length is not enough, so I needed a Wiring extension.
Once attached, the Switch looks as if it has been around for a long time.
Above all, DL1000 V-STROM250SX Color:I like the fact that it is a YellowMODEL with a Yellow-colored switch!
View detail
Fits: YAMAHA YZ80, YAMAHA YZ250 A-C, YAMAHA YZ125, YAMAHA YTM225 DXK, YAMAHA YTM225 DX, YAMAHA YTM200 K-L, YAMAHA YTM200 EX, YAMAHA YTM200 EL, YAMAHA YSR80, YAMAHA YSR50 E, YAMAHA XT500, YAMAHA XT250, YAMAHA XT200, YAMAHA XT125 J, YAMAHA TY50 M, YAMAHA TW200, YAMAHA TT250 R, YAMAHA TDR125, YAMAHA SR500, YAMAHA SR400
Parts that are worth replacing even in NORMAL.
The handling felt heavy and a bit unmanageable, so I took it to a Motorcycle shop for a checkup.
→Steering's diagnosis was that the Ball in the Bearing was crushed. 。
It is a weak point for the SR400's OEMBearing 。
[Type of SR400OEMSteeringBearing.
...depending on the year Ball type When Angular Type." but both have low resistance but poor rigidity due to point contact.
The angularity used in older models is somewhat better than the normal Ball, but I am still concerned about rigidity.
TaperBearing was then recommended to us.
TaperBearing.
Tapered roller bearings are bearings with a structure that can receive loads generated by rotation (struss load) and axial loads (radial load). 。 The rigidity is increased to accommodate each load.
examples showing the use (of a word) ： Tapered Roller Bearings are used for axles, Engine, etc. →Seems to be rigid.
TaperBearing or ball bearing?
Ball bearing→* that which the rolling element is a ball. Ball bearing (Ball bearings)
Roller bearing. (Roller bearings)
Rolling elements are balls or rollers that are incorporated inside the bearing.
[Merit of TaperBearing
◎Handling is prone to rattling under severe use at high speeds, such as on highways and circuits.
Ball bearing→ ball-shaped, so it is weak under load and crushed.
TaperBearing→ Loads are taken up by the "wire" of the Needle, resulting in a larger bearing area, improved durability, and smoother handling. 。
In other words, the load is received in a line→ The load flows as it is because the load direction is a single line.
Effect after replacement
◎I could feel less shaking of the handlebar at high speeds, and could sense that stability had improved.
◎SelfStir can be easily taken out. as Image, put the one in the direction you want to turn lightly, and Image turns smoothly.
◎Push walking became somewhat easier.
By changing to this, we were able to experience an increase in rigidity.
The difference is especially noticeable at high speeds and in situations where the front load increases, such as when driving at high speeds and in situations where the front load increases due to winding.
TaperBearing is a good thing, but it also has its weak points.
[Weaknesses
Due to the increased resistance caused by the surface contact, it is not good in the speed range from very low speeds to street level speeds.
The lightness of the OEM is slightly outweighed by the lightness of the OEM.
Considering MaintenanceCycle and Cost performance, if you judge overall, I think OEM Angular is a good choice for those who ride Main in the city. For those who want to enjoy touring and winding with high speed driving in mind, we definitely recommend the Taper.
*It is better to have the replacement done at a Motorcycle shop if at all possible.
View detail
Fits: BMW R1200RT, BMW R1200RS, BMW R1250RT, BMW R1250R, BMW R1250RS, BMW R1250GSA, BMW R1250GS, BMW R1200R, BMW R1200GSA, BMW R1200GS
self-satisfaction
I bought this lever for my R1200R. I was looking for a lever that wouldn't break when I stand on the ground, and I found this lever. I think it's good to leave the work to the shop because I can't press-fit without a tool. View detail
Fits: SUZUKI DR 125 S, SUZUKI GN 125
Installation completed without problems!
I have a gs125e, which is a motorcycle that is not guaranteed to fit, but I found this product after returning it and looking up the manufacturer part number myself because I could not install another product that was guaranteed to fit. Of course, the installation was completed without any problem!
What is a little disappointing is that webike does not have OEM Product neatly researched and listed.
View detail
Fits: HONDA CB1100, HONDA VFR800X, HONDA VFR1200X, HONDA VFR800F, HONDA CB1100RS, HONDA CB1100EX, HONDA CBF1000F, HONDA CB1300SB, HONDA CB1300SB SP, HONDA CB1300SF, HONDA CB1300SF SP
The grip width can now be fine-tuned.
It is a replacement from U-KANAYA lever as well as Brake lever.
I was able to adjust the grip to the best width after replacing it with STFLever, because it felt far away from my palm even after making the smallest adjustment with the previous Lever. At the same time, I replaced the Dust Boots of the Clutch Mask Cylinder because they were torn.
The feeling of use is closer to the Clutch connection when it is aligned with one's palm.
View detail
Cheaper than Korea by purchasing good products directly
First, I purchased a good product through direct purchase at about 2.5 times cheaper than the domestic price.
Thank you for the fast delivery, excellent quality, and packaging.
When installing, it was easy to search without any product processing or unnecessary steps, and above all, comfort was provided when worn.
Of course, the style has also been upgraded to add more coolness.
Winter has passed and now it's time to store it, but I'll enjoy it for a little while until early spring.
Due to the nature of consumables, there is room for additional purchase ------------------------------------------ ---------------- First, I purchased a good product through direct purchase at about 2.5 times cheaper than the domestic price. Thank you for the fast delivery, excellent quality, and packaging. When installing, it was easy to search without any product processing or unnecessary steps, and above all, comfort was provided when worn. Of course, the style has also been upgraded to add more coolness. Winter has passed and now it's time to store it, but let's enjoy it for a little while until early spring. Due to the nature of consumables, there is room for additional purchases. Powered by Google Translator
View detail
I really like the design and feel safe from falling.
Installed on Hunter Curve. There was some difficulty in getting the positioning for installation, but it wasn't a big problem. However, the length of the knuckle guard for versatility is long, so when the handle is steered left and right at the maximum angle, the throttle cable gets caught on the end of the right knuckle guard and interferes with it, so it was machined, cut, and installed. -------------------------------------------------- -------- Installed on Hunter Curve. There was some difficulty in getting the positioning for installation, but it was not a major difficulty. However, the length of the knuckle guard for versatility is long, so when the handle is steered left and right at the maximum angle, the throttle cable gets caught on the end of the right knuckle guard and interferes with it, so it was machined, cut, and installed. Powered by Google Translator View detail
Fits: KAWASAKI ZX-4RR, KAWASAKI ZX-25R, KAWASAKI ZX-25R SE, KAWASAKI Z650RS
Rattling is Large size
It looks cool, but the rattling is LARGE and very annoying.
Also, the wire inserts are exposed and rain penetration is a concern.
It was disappointing for Z650RS.
View detail
Fits: HONDA CBR250R (2011-), HONDA CBR400R (2013-), HONDA CB400F (2013-), HONDA 400X, HONDA glom, HONDA CB500F, HONDA CB500X, HONDA CBR500R
Good slimness.
I had been using Lidea's 3D Lever on my groms for many years, but I felt tired when touring long distances, probably because of the wide lever. I replaced it with this lever for the sake of trying it out. It seems to be much thinner, so I feel less fatigued and BrakeTouch seems to have improved. The only negative is that I have to carry Wrench to adjust the lever. My friends tell me that I don't need a Wrench once I've adjusted it, but I sometimes want to change it a little bit due to the day's conditions or changes in Gloves. View detail
Fits: KAWASAKI ZRX1200, KAWASAKI ZR-7S, KAWASAKI ZR-7, KAWASAKI Z750S, KAWASAKI Z1000, KAWASAKI ER-6n, KAWASAKI ER-5, HONDA CBR650RA, KAWASAKI Versys 650, KAWASAKI Ninja ZX-6RR, KAWASAKI Ninja ZX-6R, KAWASAKI Ninja ZX-14R, KAWASAKI Ninja ZX-14, YAMAHA FZR6, YAMAHA FZ6R, YAMAHA FZ6, YAMAHA FZ10, YAMAHA FZ09, KAWASAKI Tengai, KAWASAKI ZRX1200 DAEG
Be careful and read before you buy this.
This grip could not fit to your motorcycle. Even if the product describes you can use this, it may not be on your bike. I got one cuz it was supposed to fit my bike but it didn't. so I asked it seller(the brand Kijima) and they replied that 'This item is not compatible with Eliminator 450. Eliminator 450(US imported version) and Eliminator 400(Japanese domestic version) are completely different motorcycles. So I asked about the dimensions of the handlebars to official Kawasaki global and they replied 'The diameter of the EL400's handle bar is same as that of EL450's.' I sent this reply to the seller and got the reply 'The compatibility information on our website states that it is universal. Therefore, some processing may be required. Please understand that if a customer buys the wrong item due to a confirmation error, we cannot accept returns / refund.'. When I received this message, I gave up to claiming it and decided never to buy anything from Kijima. View detail
The feeling of use is double ○.
The way I gripped the lever caused my small and ring fingers to get caught between the lever and my fingers and my grip tended to become loose after standing for a long period of time.
The grip and comfort are good, and the replacement has made driving very comfortable and smooth.
View detail
Fits: KAWASAKI KLX250, KAWASAKI KLX230SM, KAWASAKI VERSYS-X300, KAWASAKI VERSYS-X250, KAWASAKI KDX125SR, KAWASAKI D-TRACKER X, KAWASAKI KLX300SM, KAWASAKI KLX300, KAWASAKI KLX230R, KAWASAKI KLX230R S, KAWASAKI KLX150S, KAWASAKI KLX230, KAWASAKI KLX150BF, KAWASAKI D-TRACKER125, KAWASAKI KLX125, YAMAHA XTZ125, YAMAHA WR155R, HONDA TRAIL125, HONDA CRF150L, HONDA CRF250M
Good product but shorter than I expected.
I like both the detailing and the look of the product.
But is 4Finger better for me?
It is about 2 or 5 Finger long when I hold it.
View detail
Fits: HONDA CRF250L, HONDA CRF250L(S), HONDA CRF250M, HONDA CRF250RALLY, HONDA CRF250RALLY(S)
Good product but shorter than I expected.
I like both the detailing and the look of the product.
But is 4Finger better for me?
It is about 2 or 5 Finger long when I hold it.
View detail
Fits: SUZUKI Across, SUZUKI Across, SUZUKI Across, SUZUKI Across, SUZUKI BANDIT250, SUZUKI BANDIT250, SUZUKI BANDIT250, SUZUKI BANDIT250, SUZUKI BANDIT250, SUZUKI BANDIT250, SUZUKI BANDIT250, SUZUKI BANDIT250, SUZUKI BANDIT250, SUZUKI BANDIT400, SUZUKI BANDIT400, SUZUKI GSX-R400, SUZUKI GSX-R400, SUZUKI GSX-R400, SUZUKI GSX-R400, SUZUKI GSX-R400
It was useless.
It was guaranteed to fit the gs125e, but the size did not fit and it could not be installed.
I offered to process the return, but at first they tried to process the return for my convenience.
After that, the return was processed as a warranty of conformity. I looked for alternatives, but there weren't any." But that was not the case,
I looked up the model number of the Clutch lever myself, and found that webike handles the OEM Product. You didn't look for it?
I purchased that one and installed it, and of course it was installed without any problems!
The warranty of conformity is wrongly stated, OEM Parts can't be found, and trust is lost...
Everyone should be careful when purchasing.
View detail
It came with it since I bought it used, so maybe this?
I think it's on Title, maybe this one?
It Guarded me well when I went to the forest road immediately after I bought the used one and had to do some cocking.
When it comes to CRF! I think it is a custom.
View detail
Fits: HONDA CB1300 SF, HONDA CB1300SUPER BOLDOR, HONDA CB1100, HONDA CB1000 SF (Big One)
with HoleStem Nut
Mounted on cb1300sf. To attach a hand-held SYGN HOUSE mobile Holder (c32 purchased separately) Sh,
Nut arrived firmly with Torque wrench!
I can't see much Stem Nut when I put the Mobile Holder on,
It's inexpensive. (*'▽'*) ♪
View detail
Fits: HONDA CB1100 RS, HONDA CB1100 EX, HONDA GROM 125, HONDA MONKEY125
NA Metal Craft Handle Up Spacer
The height of the low handlebar makes it more comfortable to use.
It is well made and a great part.
It's easy to install, anyone can use it, and I think it's a quality that isn't easily available.
This product is highly recommended for tall people who want to drive the Monkey 125. -------------------------------------------------- -------- You can use the low handlebar height to make it easier. It is a good and good part. I think it's easy to install and can be used by anyone and it's easy to get. It is highly recommended for a tall person to drive Monkey 125. Powered by Google Translator
View detail
I used it on my GPZ900R.
I bought this for High SoloWirefor replacement on my GPZ900R. I have been using StainlessBracket for a long time, but I bought StainlessBracket again because it is less likely to rust. The price is higher than before, so I give it 4 stars. View detail
Fits: HONDA Shadow classical400, HONDA VT250 INTEGRA, HONDA VFR400R, HONDA VFR400R, HONDA VFR400R, HONDA SHADOW750, HONDA SHADOW750, HONDA SHADOW750, HONDA SHADOW750, HONDA SHADOW750, HONDA CBR900RRFire blade, HONDA CBR750, HONDA CBR750, HONDA CBR400RR, HONDA CBR400RR, HONDA CBR400RR, HONDA CBR400RR, HONDA CBR400RR, HONDA CBR400RR, HONDA CBR400RR
Easy to grip due to its folded shape
I replaced the lever because it had been broken by a standing fender bender. I think it is easy to grip even for a person with small hands due to its folded shape. However, the quantity:Pair (for Left and Right) If you want to replace the Levers with different shapes, you should use the Quantity:Pair (for Left and Right) We recommend replacing the lever at the same time. View detail
Fits: HONDA CR, HONDA CRF, HONDA CRF-X, YAMAHA YZ, YAMAHA YZ-F, YAMAHA WR-F, KAWASAKI KX, KAWASAKI KX-F, KAWASAKI KLX450R, SUZUKI RM, SUZUKI RM-Z, SUZUKI RMX450, Others Wire clutchCompetition model
Installed on CRF125F
I broke two NORMAL clutch levers, so I decided to replace the entire holder with this lever for the third one.
Installation was no problem, as it was only assembled once RoseRose.
If an OEM lever was used, the clutch switch terminal would be attached to the base of the lever, but the ZAP lever does not have one, so the wiring coming out of the body of the car must be made to conduct.
I think it is lighter than OEM because it can be shortened and set closer together.
It looks cool and I am satisfied with the Up operation.
View detail