Reviews
SWCondor Reverse Attachment
I wanted to make it look like a separate handle easily, so I reverse-attached it.
Since it interferes with the tank, I purchased a separate Handlebar Stopper and adjusted the angle to avoid fatigue.
It took a couple of days to get used to it and now it is comfortable.
Corner rings are now easier to put on, I feel more at one with the bike, and wind resistance has been reduced, so it is very comfortable.
View detail
Fits: KAWASAKI D Tracker, SUZUKI DR-Z400SM, SUZUKI DR-Z400S, HONDA CRF250M, HONDA CRF250L, KAWASAKI KLX250, Others
Handlebar exchange
Handlebar was bent and had to be replaced.
We decided to use the same Brand that was originally installed.
View detail
defective
The mounting hole for the switch box on the right side of the handlebar is too large and the switch box is not secured. I was worried about replacing the handlebar by myself, so I asked the shop to do it, but they told me that the switch box could not be fixed due to the above reasons. Also, as for the Handle end cap, the OEM Product was not available and we had to order a new HandlebarCap. There was no mention of this at the time of order, nor in the Instruction Manualetc. I am appalled that this is an exclusive product. View detail
SR400 is perfect.
I reverse-mounted it on my SR400. I like the angle of the droop and aperture, and the texture of Stainless Steel. The switch, grips, and wires are also fine as they are in NORMAL. View detail
Fits: HONDA FORZA 300
ตรงรุ่น Forza300 ส่งรวดเร็ว บริการดี View detail
Condor retrofit
I installed it on an ST250E. I tried to adjust the angle so that it would not hit the tank by reversing it, but the opposite side was no mark! The Handlebar Stopper was installed in a hurry and now I am happy with the Handlebar. View detail
Handlebar replacement to improve position
The Intermediate is the perfect height and the Riding position is perfect. View detail
Color is not good
Color of the product:I had been using Gray, but ordered Silver as a color change.
I was expecting a shiny Silver, but the texture is not so good as it looks like a dull Clear on the surface.
Color:Gray has a better texture, but this one is also halfway in color, so I used Silver.
I forgot the weight of the OEM, but this one weighs about 580g, which is about half of what I feel.
The inside diameter is 14mm and Universal Handlebar could be used without any problem.
Position is between Cafe and Muji.
Shoulder stiffness due to the wide width has been improved, but it is not suitable for long distance because it is low.
Without the extended spacer, the car will not pass inspection, but if you pay about 5,000 yen at a plaza during the inspection, they will change the structure, which is better than buying a spacer.
View detail
I hope it's easier to ride.
I replaced the REBEL Handlebar because it felt wider.
I think it narrowed a little bit and came a little bit closer to the front.
I also feel that the vibration from 70K to 100K has been reduced.
As for me, it is GOOD.
View detail
NicePosition
It took a lot of time and effort to replace it, and although I haven't tried it out yet, it feels pretty good to straddle. View detail
Work is LargeChange
The handlebar itself is narrower and easier to position. The problem was the installation...as is typical of all Kawasaki motorcycles, the bar end was stuck and it took more than 2 hours to disassemble the bar end. As a result, it took me a whole day and about 5,000 yen for the parts. Unless you have confidence in Kawasaki Motorcycle's maintenance, or you have secured all the maintenance parts, it is not a work that an amateur can do. Please be sure to prepare for the work before you do it. View detail
Fits: HONDA FTR223, Others , SUZUKI GRASS TRACKER Big Boy, SUZUKI GRASS TRACKER Big Boy, SUZUKI GRASS TRACKER, SUZUKI GRASS TRACKER, HONDA MONKEY
DL1000 V-STROM250 Handlebar replacement
Installed on VSTROM250 。 The handlebar is narrow and has a strong aperture. The width is the same as SEROW, which improves the riding posture. However, the clutch wire and brake hose are tight and the hose guide has to be removed. I have no problem because I use ThailandBand to hold the necessary parts. View detail
Fits: HONDA MONKEY, HONDA MONKEY, Others
It's OK when it's zoomer row!
The width of the handle is moderately narrow based on the Zummer low, so it is comfortable and good when changing directions.
If the low seat is alibal, the position is considerably backward, so the position is more comfortable when the footrest on the rear chassis is installed rather than the front footrest.
It's much lower than the genuine one, but I haven't applied it to the genuine seat frame yet, but I'm satisfied with the price. ----------------------- The handle mob is moderately narrow based on zoomerow, so it is comfortable and good when turning. If the low sheet is ali-ball, the position will go back to the back, so the position of the rear car is installed rather than the front paws. It is much lower than pure, but I haven't applied it to a genuine seat frame yet, but I'm satisfied with the price Powered by Google Translator
View detail
Fits: YAMAHA MT-09, YAMAHA XSR700, YAMAHA XSR900
Yamaha FZ-09 Handlebars
Awesome. Handlebars arrived in 5 days. Product was packaged well. Looks like it will work great with my FZ09. Great service. Will buy from again. View detail
ZETA CompleteHandlebar SEROW250
The holes were pre-drilled and easy to install. The design is good, and the handle position is good for standing on forest roads. View detail
Fits: SUZUKI RM250, KAWASAKI KX250F, SUZUKI RM125, SUZUKI RM-Z250, KAWASAKI KX250, KAWASAKI KX125
Blue color matches Kawasaki color
I have a 97 klx250es with mx-214 Blue.
The color matches very well, and the position is just a little bit of an angle of the bar, mx-412 for the best match with the Fork angle.
or mx-415 is preferred.
One regret is that the angle of the center reinforcement bar was slightly forward of the horizontal bar, so we loosened the bolt and slightly deformed the old clamp to somehow make it flush with the horizontal bar. The center reinforcement bar is often installed at a slightly tilted angle from the horizontal to the front.
View detail
Praise!
It leans forward a little, but not so much that it's tight, and the Corner is not too bad. I think the Large is strong enough for long distance touring. View detail
Fits: HONDA glom, HONDA glom
Posture changes
Product Name
HURRICANE HURRICANE Forward Conti2 type Φ7/8 inches Handlebar
Item Number
HB0038B-10
Vehicles
Grom ( JC61 ) 2015
Number of man-hours
About 1 hour
Required Tools
Torque wrench, hexagon socket, Hexagon socket, Extension bar, Combination wrench, -Driver, Hammer, Pliers, etc. would be perfect.
Why did you choose this product?
When we installed Grom's Rear Sets, we thought it would be better to change the handlebar as well, so we chose this one. I also found many people on the Net who had chosen this handlebar for their Groms, so I decided to purchase it.
Was the one you received as per Image?
It was as shown in the Image, only with Handlebar.
Was the installation difficult?
I think it is easy because the mounting holes are already drilled. However, if you don't organize and move the Cable system, it doesn't fit very well. It took me a long time to fix that part.
How was your experience with it?
The posture has been changed to an aggressive posture. By changing the position of the hips, you can go from a forward leaning posture to a comfortable upright position.
[Was there anything that disappointed you?
Nothing in particular. I would be happy if it were cheaper.
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
View detail
Prevention of CRF vibration
The Initial Model 2017 CRFrally vibrates quite a bit in the Handlebar.
After an hour of driving at 100 km/h, my hands are chattering so much that I think I have vibration disease.
It vibrates quite a bit when driving at medium speed in town and accelerating.
I was thinking of adding Handlebar Weight to prevent vibration.
I'd rather replace it with one that has Inner Weight.
ZETA Zita EXPLORER Handlebar T-1 Touring is,
From the beginning, Inner Weight is Quantity:Set and designed for safety.
HandlebarGrip (Pro grip601), Special Bond, Open end Throttle
4-point Quantity:Set is ordered via webike.
Handlebar itself is not the OEM floppy painted Black.
The shibu Black matte Black has been used to tighten up the whole look.
Vibrations were also reduced considerably, which we thought was a good thing.
The Handlebar Brace portion has also been thickened, making it easier to attach a Smartphone Adapter or Navigation.
ArmourGuard is not attached because it does not protect against vibration.
Additional new Tsuo measures with GelType on Grip.
We are now satisfied with the look and performance of the product.
Quantity for installation:Pair (for Left and Right) 5mm hole drilling is required in the handlebar to stop the switch actuator of the
Electric Drill and 5mm Drill blade for steel are required.
Since facets are produced quite a bit, it is necessary to lay out a 2M square blue sheet before cleaning up afterwards.
If you do it on dirt or something else, the facet is in danger of not being retrieved.
Be careful not to get it in your eyes. Worst case scenario, you could go blind.
View detail
Fits: YAMAHA MT-09, YAMAHA XSR700, YAMAHA XSR900
XSR900
Great handlebar for xsr900. Install was great and easy. Took about an hour to do. Cheap and very fast shipping. Highly recommend View detail