Reviews
Not Standard Size
25.2mm, so it will be sandwiched between the rubber plates.
However, Rubber sticks out, does not pinch properly, etc. Stress builds up subtly.
In the end, I managed to attach it, but I was not satisfied with the wobble, the subtle texture, and the fact that it was rather large for a skimmer Switch.
I think it would be better to use a 22mm size made by NAKA0 with waterproof and wiring processing...
Well, it's too much trouble to replace it, so I'll use it until it breaks.
View detail
I lost it, so...
22.I lost my ClampSpacer for 2mm, so I bought Repair Parts.
Only Repair Parts can be purchased for fragile parts, so they can be used for a long time.
View detail
Size is Small
DAYTONAGoat Skin Gloves Punching meshGloves ProtectionType L Size
The price is kept low, which is a wonderful thing. The fabric is soft and I thought it might be thin, but it has a good thickness and a solid impression. The palm of the hand is quite well made and fits naturally to the Grip. The thumb can be bent easily, so the grip is good. Vibration is also suppressed, I think. The size is a little small. (These are my impressions with the Goat Skin Glove Protection Type as standard.)
Comparison products
Goat Skin Glove Protection Type L Size
Item Number : 76367
View detail
Feeling flow instability as per other impressions.
I use it because I often Overflow on my old car.
I'm not particularly particular about the Manufacturer, but DAYTONA seems to be well worth the price. There are no visible defects, such as paper wrinkling.
However, as mentioned in other impressions, the flow rate seems to be lower than other companies' products, and sometimes the Gasoline would run out at full throttle on the freeway scene, etc. (Waiting a bit will fix it.) Also, the Gasoline would suddenly stop running due to air bite, although the cause was unknown (I'm not sure if this was due to the Direct product, but removing the filter would fix it). (I don't know if this was due to the Direct product, but it was fixed by removing the filter.)
Therefore, it is not very useful for 250ccSports type motorbike.
I will look for a product with a higher flow rate.
View detail
It slips and moves.
Used to attach the Smartphone Holder to the Pipe behind the Screen on the Honda 400X (2019) (with an additional Spacer that comes with the Smartphone Holder).
The size itself is just right, but the hard rubber makes it slippery, and even when the bolt is tightly tightened, it slips and moves. Therefore, I wrapped a thin double-sided tape around the pipe on the body side before installing the bolt, but it is not completely fixed because the outer side of the bolt also slides.
I'm considering replacing the Arm of the Holder with an aluminum spacer only for the type that is tightened with ZETA Bolt.
View detail
Although inexpensive genuine leather Jackets are available ...
From a distance, it looks like a reasonable Jacket, but the details are very cheaply made. And the leather, which is claimed to be genuine leather, seems to be very thin. In general It's well-made, but thin and cheap." This is my honest impression. Kadoya. Ya "DEGNER" It should be considered as a separate product from It is not something I would recommend to anyone I know.
I want a leather jacket, even if it's simple and cheap." It would be safer to avoid them unless you are a person who is
View detail
Fits: HONDA , HONDA CB500X, HONDA CBR500R, HONDA Rebel1100 DCT, HONDA CRF250RALLY S, HONDA CRF250RALLY, HONDA CBR650R, HONDA CBR400R, HONDA CB650R, HONDA CB1300SUPER FOUR SP, HONDA CB1300SUPER FOUR, HONDA CB1300SUPER BOLD'OR SP, HONDA CB1300SUPER BOLD'OR, HONDA CB1000R, HONDA 400X, HONDA Rebel1100 T, HONDA Rebel1100, HONDA CBR650R, HONDA CB650R
Nice looking sticker on the tank!!
For my 2023 Honda Rebel 1100 - very simple to apply, just makes sure alcohol wipe the surface first and then line up the stick with the gas tank. You might experience some unaligned screws holes on the sticker, in that case use a heat gun gently on it then use hand move the stick to the proper positions. Overall - nice looking products but for almost $20 I think is little over price, and not sure how long it last. View detail
Air bubbles unavoidable
I bought for 2023 Honda Rebel 1100 - The package comes with 2 set of film of both lens (round odometer and half moon shape engine light), package comes with instruction and the material of the film is good maybe too good of the thickness. (I’ll explain below), I have done film, carbon film wrapped and window tinting myself, this odometer film should be simple and easy as instruction said: 1. Alcohol wipe. 2. Peel half the back sticker and spray with water, 3. Apply to the sticker onto lens and spray water then peel off the back sticker. 4. Use a film squeegee push out the water and air within. Unfortunately, I wasted both set not able to 100% eliminate air bubble, no matter what there is at least 30% air still capture within and if you try too hard you’ll damage the film, I believe the quality of those film it’s too thick couldn’t able to squeeze properl, I even let it sat under the sun for 2 days hopefully it’ll take off the bubble it still remain the same amount… If you not looking for perfection then this might work for you, but I can’t stand the bubble ended peel them all out and threw it in trash. I think for over $15 this should be a nice and easy to use products, is not worth the money. View detail
Higher height.
I bought this when the Autofocus on my previous iPhone 11Pro Camera broke.
Type VibrationControlDevice to be attached to existing Smartphone Holder3
Just Smartphone Holder3+ IH2100Rigid (25077) The pull-pull mechanism is about 20mm higher than that of the "M" and it shakes more when a smartphone is attached.
I think it can absorb a certain amount of vibration, but the increased height makes it look bad.
If I were to purchase an expensive SMARTMonitoretc. without a phone attached, I would be willing to purchase a used Android phone and use it with TetherRing.
View detail
Fits: KAWASAKI ZZR1400, KAWASAKI ZX-6R, KAWASAKI ZX-6R, KAWASAKI ZX-14R, KAWASAKI ZX-14R, KAWASAKI Z1000, KAWASAKI 1400GTR
Pad replacement
Normal. Good cosmetics. Large inventory. View detail
Air bubbles will be noticeable.
My first impression was that it was smaller than I had expected.
It is a little small for a Large Motorcycle, giving the impression of unbalance.
The advantage is that it is transparent and allows the best of the paint to be used, but on the other hand, air bubbles can be noticeable, so it must be properly warmed up and applied neatly.
If the angle of the tank is sharp, the edges will peel off, so you need to warm it up thoroughly and degrease it before applying it. I replaced the tank pad with another one because I was concerned about air bubbles and the shape of the smallest tank.
View detail
Fits: SUZUKI GSX-S1000, SUZUKI GSX-S1000 F, SUZUKI GSX-R1100, SUZUKI GSF1200, SUZUKI GSX-R1100, SUZUKI B-KING, SUZUKI GSX1400, YAMAHA YZF-R25, YAMAHA WR250X, YAMAHA WR250R, YAMAHA XJR400RII, YAMAHA DIVERSION, YAMAHA XJR400R, YAMAHA XJR400R, YAMAHA XJR400S, YAMAHA XJ400ZE, YAMAHA XJR400, YAMAHA XJ400Z, YAMAHA XJ400ZS, YAMAHA XJ400D
UV sensitive, torn after one year.
The 2LSize is too small for the MT09. Also, it seems to be weak against ultraviolet rays, and the part that was exposed to the sun well deteriorated and tore after not lasting a year. View detail
Dissatisfied with volume
Even though it is JMCA Certified, I bought it thinking it would be a little louder and have a little more edge to it, but it was quieter than I expected. I honestly feel that it is not enough for me.
The rest of the installation is intended to replace the Normal muffler,
I had already installed a center stand stopper, but I needed a bracket to install a normal muffler and a NORMAL exhaust band. (Parts that bind Exhaust pipe and Exhaust System)
I did not have any and had to buy more.
That's all I have to say about my dissatisfaction.
Other than that, there were no problems.
The packaging was beautifully applied and the delivery was fast.
View detail
Too big, mostly for Wheel
[How is it used?
For undercarriage wash of Motorcycle
Was the one you received as per Image?
It is so much bigger than I imagined. It looks like the size of a car wheel brush. It has a Size feeling like a Brush for a wheel of a car.
How was your experience with it?
It is indeed flexible, but I think it is too big and not suitable for washing motorcycles. If it were half the size, it would be easier to wash the area around the rear shock and around the engine through the cowling, but I don't want to accidentally damage the paint with it.
It would be good for something like NAKED with an air-cooled engine.
[Points to note]
The bristles are too hard to wash painted surfaces, so it is mostly used around the feet and engine area.
[Opinions and requests to Manufacturer
Put it out half as fine as it already is.
View detail
To One point Accent.
I purchased the Yellow color.
The color is vibrant when just installed.
It fades quickly.
Let's buy another one.
View detail
Commonly usable
I've only used it once, but it works for a change. The air injection type took some time and effort.
In terms of texture, my sleeping posture may not be good, but I had a sore neck the next morning.
Since it is so cheap there, it is not bad from a cosmetic standpoint.
View detail
I want you to write down the Large size of Disc Lock.
The wire lock works normally, but the disc lock could not be used due to its large size.
REBEL250
View detail
Fits: Others CR-mini Carburetor, Others PECarburetor, Others PWK Carburetor
The price
Aside from the hole Sizeetc., the overall construction (finish) is clunky compared to KEIHINOEM and POSH's Jet.
Well, I guess that means it is in line with the price. Well, it does its job as a component, so it's fine.
View detail
Fits: SUZUKI GSX-R1000R, SUZUKI GSX-R1000R
A little difficult to use.
Used on MF17 with FORZABOX. There is no problem with the dimensions, but there is only one place on the back side to squeeze the hem strap, so it is difficult to squeeze the hem as desired. The other manufacturer (company name withheld) that I used to use on other motorcycles was very easy to use because it had both front and rear hem apertures. I bought this one because that manufacturer was expensive, but after about the fifth time I used it, the place where the string comes out was torn because I pulled it too much, so I ended up replacing it. It is too good to throw it away, so I will keep it for two sheets in case of stormy weather. I'm going to give up on it. View detail
Fits: KAWASAKI Z250, KAWASAKI Ninja250, YAMAHA TZR50R, YAMAHA TZR50, YAMAHA TZM50R, YAMAHA TZ50, TRIUMPH TIGER1050, SUZUKI BURGMAN400, SUZUKI BURGMAN400, SUZUKI BURGMAN200, SUZUKI SKYWAVE400 burgman, SUZUKI SKYWAVE250 burgman, SUZUKI SKYWAVE250 burgman Type S, SUZUKI SKYWAVE250 burgman TypeM, SUZUKI SKYWAVE250 burgman SS, SUZUKI DR800S, KAWASAKI ELIMINATOR 125, KAWASAKI Z400, KAWASAKI Z400, KAWASAKI Z250SL
Used for VERSYS-X
No complaints about the price if it holds up.
4,000 kilometers and I'm down to less than half of that.
Cost will be high because it decreases quickly.
View detail