Reviews
Fits: KAWASAKI Z900RS CAFE, KAWASAKI Z900RS
light
[How is it used?
After installation, the car traveled about 200 km.
Was the installation difficult?
It is not so difficult to install except for the Flange, which is a type of two-piece flange, so it is difficult to install unless you get under the motorcycle.
How was your experience with it?
The OEM one is quieter, both idling and running, but the OEM one is louder. Personally, I was satisfied with the quietness, as it was just right for me. The sound quality is not as harsh as the OEM, but low and smooth.
Lightness is somewhat felt when pushing and pulling.
[Was there anything that disappointed you?
There are too many springs to install, but since spring hooks (devices) are not included, it is better to prepare them.
[Others]
Point or hang for installation...nothing special. If you dare to say so, there is no need to twist the O2 Sensor when installing it. If you install the O2 Sensor lightly before fixing the middle Pipe and turn the Pipe side around, you don't have to worry about the O2 Sensor wiring twist.
Availability and clarity of Instruction Manual - I can understand without it.
Items to buy together...Gasket is a good thing to have. The only other thing I need is heat resistant grease.
【Review】
Personally, I don't like the length of the exhaust end, the degree of raising, and the color (I prefer shorter, lower, and Polished Titaniumium), but I am very satisfied with the lightness, the Hand Bent-like curve of the exhaust pipe, and the high quality sound.
View detail
Quality is poor for the price.
It is a reasonable price, but I don't think the quality is good. There were welding spatters all over, BALI all over the part where the Bolt is inserted, and even scraps from cutting the Screw. View detail
Hmmm...
This is a replacement from OHLINS Grip, but the Fitting is poor.
It can be installed, but it does not feel right.
Is it expensive for the accuracy?
View detail
Fits: HONDA CB1100, HONDA CB1300 SUPER BOLDOR, HONDA CB1300 SUPER BOLDOR, HONDA CB1300SF, HONDA CB1300SF, HONDA CB1300SF, HONDA X-4
K-Factory rear shock slider
Ok so I was expecting the slider to be bigger than it was so not sure it will offer much protection,I can say that the product is well made and looks nice when fitted View detail
Fits: HONDA CB1300SF, HONDA CB1300SF, HONDA CB1300SF, HONDA CB1300 SUPER BOLDOR, HONDA CB1300 SUPER BOLDOR
K-factory radiator core guard
Now if there is a difference in width size of the radiators I had to re-drill the holes on the side brackets by about 5mm each side then the cover slotted over nice and tight so expect there could be some adjustment needed View detail
Fits: KAWASAKI ZRX1200, SUZUKI GSX1300R GSX1300R HAYABUSA, SUZUKI GSX-R1000, SUZUKI GSX-R750, SUZUKI GSX1300R GSX1300R HAYABUSA, SUZUKI GSX-R1000, SUZUKI GSX-R1000
Brembo caliper essentials
I was going to buy KOHKEN 18mm, but I chose this one because the hard anodized aluminum one was discontinued.
The thing is well made and just fit the OHLINS Fork.
Since it is made with high precision, I installed it by tapping it with a Hammer a little and press-fitting it.
It is better than I expected.
View detail
Fits: KAWASAKI ZZR1400, KAWASAKI ZZR1400, KAWASAKI ZZR1400, KAWASAKI ZZR1400, KAWASAKI ZRX1200 DAEG, KAWASAKI NINJA ZX-14R
The quality of the product is perfect. I appreciate that I can adjust it quickly without using any tools.
That was a good purchase
I appreciate the ability to quickly adjust without using tools.
No complaints about the texture.
View detail
If Rolex made motorcycle parts
This K Factory triple tree is almost to nice for installation, I'd rather just look at it on the table all day! The quality of the finish and machine work is unreal. You can tell some real pride goes into the craftsmanship of these parts. They are nothing short of top shelf custom parts. View detail
Incredible quality and finish
K Factory really puts out the top shelf parts. No, they're not cheap but you really get what your paying for. The black anodized finish looks amazing. The welds and machine work are almost works of art. Shipping is suprisingly fast from Japan too. View detail
Fits: KAWASAKI NINJA1000, KAWASAKI NINJA1000, KAWASAKI NINJA1000SX, KAWASAKI ZRX400, KAWASAKI ZX-10R, KAWASAKI ZX-10R, KAWASAKI ZX-10R, KAWASAKI ZX-10R, KAWASAKI Z1000, KAWASAKI Z1000, KAWASAKI Z900RSCAFE, KAWASAKI Z900RS
Essentials for Full Exhaust System Replacement
Purchased to replace with Full Exhaust System.
Failure to replace the Exhaust System when it is replaced may result in waste leakage.
It has always been the case, but it often falls off when replacing Gasket,
It is easier to install if you apply a thin layer of silicon grease and stick it to the Engine side.
There is a way to lightly crush the Gasket circle to make it an oval and attach it, though,
I use Grease because it seems to be less efficient for disposal.
View detail
Interference at Bottom
For various reasons, when I removed the FrontStubby, I felt it was not enough, so I installed the Fork Guard.
Depending on the type of car, it may interfere with the Upper Cowletc. when it is bottomed out.
Please note that this is a GPZ900R and it will hit you in the guts.
My personal opinion is that the Bolt is Torque but I liked the hex on the pot. (tooling comes with it).
View detail
Requires considerable processing
[How is it used?
The product is good, the angle can be adjusted freely.
Was the one you received as per Image?
That is correct.
K-factory's products are always of high quality!
Was the installation difficult?
It was super difficult.
It cannot be used normally without considerable processing.
Specifically.
The OEM key cylinder is secured with an anti-removal Bolt and cannot be removed without using destructive methods. ItsQuantity:It took me 2 days to remove the 2pc Bolt. hang it, heat it with a heater fan, and blow on it for about 10 minutes to melt the screw lock agent. In some cases, if the bolt does not turn even after heating, the OEM Top Bridge is cut and removed without removing the OEM CableBracket. (like a spring) must be removed to attach it to the Top Bridge here.
There is also no hole to fix the Handlebar Switch.
I don't think this is possible. Without any holes, the Handlebar SwitchBox cannot be fixed. Turn. You need to measure the position by yourself and drill the hole with Drill. If the position of the hole is slightly off, that's the end of it. The preparation for this is the Large thing.
Lastly, I think the fact that it does not come with a bar end is a bit odd, don't you? I installed it by modifying DAYTONA's bar end for 14mm. It is not usable without past.
The above is almost impossible to install without PRO or considerable skill.
There are many tools to use and experience is required.
How was your experience with it?
Installation was difficult, but Position is easy.
[Included Parts:were they on?
Instruction Manual only but it is hard to understand.
[Was there anything that disappointed you?
No Handlebar Switch fixing holes
It took a lot of time to process.
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
Need 32mm Socket to remove Stem Nut.
It is likely to destroy the OEMBridge.
View detail
K factory Link Plate
ReliableManufacturer and looks good Parenthesis! View detail
It's a shame, because Parenthesis looks great.
[How is it used?
I switched my car to a Z900RS and the NORMAL sound was not bad, but
Purchased because the sound quality was a little different from my taste and I wanted to change the appearance and reduce the weight.
The following imprements were installed on a previous Z900 (unmarked)
Full titanium exhaust & SC1-RSilencer by SC-PROJECT
This is a very dry comparison with
Was the one you received as per Image?
Material:I found it surprisingly heavy for this Size in Titanium.
The slanted area on the opposite side of the exit has a rough surface like sharkskin.
Was the installation difficult?
When installing the inner baffle, use a ring to hold it down so that it does not wobble inside.
The system allows the user to enter the parts, but there are many similar parts, so it was difficult to know which parts to use.
I wish they would number the bags containing the Parts.
Silencer band is included, but you need to prepare your own bracket and bolts for fixing.
You need to be creative and inventive yourself.
I installed it in combination with K-fac's CLRExhaust pipe,
The bracket is Nankai Parts' Universal Bracket Length 225mmOffset 75mm (Part No. MSTL-225FR-75),
The silencer was fastened to the OEMLoading Hook by using the OEMSilencer Fixing Bolt.
Spring is the one that came with the CLRExhaust pipe.
However, the Silencer band is a little small in diameter and deformed when used as it is.
The bracket is then connected to the OHLINS Preload Adjuster.
Spacer of 3mm was put in because of interference.
How was your experience with it?
In combination with K-fac CLRExhaust pipe, even with inner baffle in place.
Considerable blast from Idling.
It might be more annoying than the SC-PROJECTFull Exhaust System without Baffle that was installed on my previous Z900 with the same Straight structure.
The Z900 series has a high ColdStart Idling.
Idling in a residential area is a Level that is sure to be Objection from neighbors.
Baffles can be attached to the exits as well,
It sounds like a whistle, like a Large Dump car, and I can't bring myself to use it.
The sound quality is rough and muddy from Idling with CLRExhaust pipe + Inner baffle.
The sound does not become a clear high-pitched or pleasant sound as it is turned, and it remains a harsh, dusky sound until the very end.
The trend may be similar to the OEM sound.
It seems that the inner baffle is causing a lot of exhaust resistance.
I don't feel that the low speed Torque is extremely gone and AfterFirea is not at all.
I feel that the performance has been downgraded quite clearly because it feels like it is jammed on top despite the bombast.
I tried running the next day WITHOUT Baffle's full Straight and it was so loud that I could say it was heinous.
Level, which is no different from the straight pipe of a family car.
The sound quality and running are better than with Baffle, but at any rate, it is too noisy.
It is highly likely that we will abandon the use of the system, although we need to consider whether we should compromise on driving and sound by emphasizing style.
Very disappointed because I like the look of Large.
Link pipe and Quantity as Slip-on Silencer for Z900RS OEM exhaust pipe:There are some that are sold Set.
It might work there.
[Included Parts:were they on?
・Instruction Manual
Silencer Band (possibly Material):(Stainless Steel)
Adapter for mounting on 54mm exhaust pipe, Spacer, etc.
1 pc. each of exit and inner baffle for installation.
K-fac Emblem
(Spring not included)
[Was there anything that disappointed you?
I was expecting the sound quality to be clear and pleasant like the previous SC-PROJECT car.
With Baffle, it was like a very loud OEM that I didn't like.
The sales pitch was that the volume could be adjusted by using a combination of inner and exit baffles.
The volume of the Inner is not as low as expected, and the sound quality is poor.
Exhaust resistance is too Large and performance is down from NORMAL to Large.
Other items that would be helpful
Items to buy together:.
This is a Universal Product, so brackets, springs, bolts, etc. for fixing the silencer are required separately.
View detail
Invisible part
The Chromoly steel may be more durable than the OEM product. It is not that the durability of the OEM product is bad in the first place, it is just a self-fulfillment. It is not that the durability of the OEM product is bad in the first place. View detail
Fits: KAWASAKI NINJA ZX-14R, KAWASAKI ZZR1400, KAWASAKI ZZR1400, KAWASAKI ZZR1400, KAWASAKI ZZR1400, KAWASAKI ZZR1200, KAWASAKI ZRX1200 DAEG, KAWASAKI ZRX1200, KAWASAKI ZRX1100, KAWASAKI ZZR1100, KAWASAKI ZZR1100, KAWASAKI GPZ900R, KAWASAKI GPZ900R
I like it.
Many users seem to use the OEM release of the ZZr1400, but I chose this one. I replaced the clutch master with this one right after purchasing the car, and I also replaced the clutch master at the same time, so I am not sure if the clutch lightening effect was effective or not, but I had enough time for a downhill touring of about 200km without any grip fatigue. However, when combined with brembo 17RCSMASTER, I feel that the stroke is a little insufficient, but there is no trouble such as difficulty in entering the GEAR. The installation is not particularly difficult as all you have to do is remove the OEM and replace it with the new one. View detail
countermeasure against standing up
Coloring also matched Cafe in Black??Gold.
We won't know the effect until we take it down, but installing it as an insurance policy gave us great peace of mind.
View detail
Fits: KAWASAKI Z250, KAWASAKI NINJA250SL, KAWASAKI Z250SL
Initial Adjuster functionality is also available
I use it on my Ninja 250SL that I ride for Circuit Racing.
It is a little difficult to tighten the screws while shrinking the springs during installation.
It is not a bad product with a good texture.
View detail
Change Shaft Holder
I think it looks good.
TIGHTLY and MOCHILIOUSLY!
View detail
Fits: KAWASAKI Z900RS, KAWASAKI Z900RS, KAWASAKI Z900RS CAFE, KAWASAKI Z900RS CAFE
Disappointed with the roughness of the finish.
[How is it used?
I switched my car to a Z900RS and the NORMAL sound was not bad, but
Purchased because the sound quality was a little different from my taste and I wanted to change the appearance and reduce the weight.
The following impressions are in comparison with the SC-PROJECT full titanium exhaust that was installed on the previous Z900 (unmarked).
So it is very dry.
Was the one you received as per Image?
The finish was worse than expected.
All of the pipes have scratches from the manufacturing process, and all of the exhaust pipes have weld marks.
It looks as if it is not a Pipe, but a plate material that has been rounded and welded.
The surface of the bending part is decorated with wrinkles.
Roughened surface like sharkskin can be seen throughout the entire surface (especially on Tail Pipe). (Tail Pipe is especially bad.)
Material:I also felt it was surprisingly heavy for Titanium.
The SC-PROJECT product was surprisingly light, with excellent finish and precision.
I assume the lightness is due to the use of thinner-walled Pipe than this product.
Naturally, the thinner the material, the higher the technology required for bending and welding.
Was the installation difficult?
The joint with the Tail Pipe also went in without any problem when combined with the same K-fac Bullet Silencer.
Aluminum's split flange seems easy to install, but in reality, it is not easy to install on the Stud.
It is difficult to do because of the "Rose" effect.
The installation of the assembly was easy, with no particular misalignment.
Clearance with the lower part of the Engine is quite low, making it difficult to set an extreme Pushing Up Style.
The Bracket that fixes the Wiring of the OEM's Lambda sensor was removed because it hit the assembly area.
The Lambda sensor mounting part is for the Z900RS, but for some reason, the position is on the opposite (back) side of the OEM.
It looks hard to do when removing it because it is about 10 cm away.
Since there are only two fixation points, one at the exhaust flange and the other at the silencer, it can be used for a long period of time.
Durability is a little uncertain.
How was your experience with it?
The thick exhaust pipe that looks like a hand bent, and the silencer angle of the pusher is also good for Parenthesis.
Material also gets a burnt color if it runs.:The good thing about TitaniumExhaust pipe.
The sound may depend on the Silencer combined, but since the catalyst and SaPig equalizer are eliminated, the sound is basically bombastic.
The sound quality is muddy from the Idling, with a rough, dusky sound rather than a clear, pleasant sound.
Exhaust pipes are just bundled together and not etc. length, which may cause turbidity due to exhaust interference, etc.
Frankly, I do not prefer it compared to the pleasant sound of SC-PROJECT.
Combined with Bullet Silencer but with Inner baffle
It seems that the exhaust resistance is quite low and I don't feel that the low speed Torque is extremely low, nor is the AfterFire at all.
It feels like the performance is down because it feels like it is stuck on top of the bomb.
I would like to eventually try it withwithout Baffle and other Silencer to see how the volume, sound quality, and performance changes.
If you think that you can get a Titanium Full Exhaust System at a relatively low price if you choose a cheap Silencer, you can get a Titanium Full Exhaust System at a relatively low price.
I would recommend it if you think it's cosmetic but don't care about the rest as long as it looks good.
[Included Parts:were they on?
Instruction Manual、Material:Includes AluminumFlange and Spring. (Also available for SilencerSpring)
[Was there anything that disappointed you?
As already mentioned, the roughness of the finish, weight, and sound quality are all disappointing.
Perhaps it was made by an apprentice? The finish makes you think
I must say that it is a bit disappointing to ship this Level in a product that costs more than 100,000.
According to the Instruction Manual, it is not returnable once the Vinyl containing the respective Parts is broken.
It is better to Check well before opening the package.
What does it mean that the initial four-month wait was suddenly delivered the following month?
Would it be too much to suspect that a B-grade shipment was made...
Other items that would be helpful
Items to buy together:.
This product is a PipeSingle Body, so a silencer, silencer fixing bracket, etc. are required separately.
View detail