Reviews
The construction is not very good.
Starting with OEM TypeReplace products, I am a little concerned about the durability and manufacturing. I guess it can't be helped that they are made overseas. View detail
Fits: KAWASAKI Z900 (KZ900), KAWASAKI Z750 (air-cooled), KAWASAKI Z1000 (air-cooled)
There were no concerns about quality.
I think the quality is almost the same etc. as OEM. View detail
This one's better.
I was surprised to see the Horn on the wall, so I immediately went for this product, but at first I put on Black, but I couldn't see the letters and the texture was too cheap, so I switched to Plating. View detail
![Z2 Type LED Tail Light Set [Fender Eliminator Kit Type-II]](https://img.webike-cdn.net/catalogue/images/69679/189-1341_l_TS.jpg)
Fits: KAWASAKI Z900RS, KAWASAKI Z900RS CAFE
doubt
The OEM Tail is cut at an angle, whereas this product is designed to be straight and flat.
If you prefer a modern look, OEM is the one for you.
View detail
Quality Improvement
The quality improvement is incomparable to that of the Normal seatBelt.
This PMCZ2Type is set up to go through a folded hole, so even beginners can install it easily!
The folded back belt also comes with a special bracket, which also gives it a luxurious look.
The bracket that fastens the Seat is too cool and shiny.
Anyway, no complaints!
View detail
Fits: KAWASAKI Z1 (900SUPER4), KAWASAKI Z2 (750RS/Z750FOUR), KAWASAKI Z750 (air-cooled), KAWASAKI Z900 (KZ900), KAWASAKI Z1000 (air-cooled)
Essentials when replacing Sprocket
I use it all the time when replacing ChainSprocket.
I tighten the DriveSprocket with pure STD nut without using lock nut, but if you use this lock washer and bend it neatly, the nut will not come off or loosen so easily.
Naturally, each time the Sprocket is replaced, the lock washer is also replaced with a new one.
View detail
Dress-up
Horns are attached to hide the bare Horns and for detail up.
The plating was peeling off after about 20,000 km. 。
It would have been better if it was 5mm lower because it interferes with the optical axis adjustment screw of the headlight, but it is acceptable because it is only touched occasionally.
View detail
The color...
I bought Black, but it was not Black, it was a bit greenish Black. View detail
Fits: KAWASAKI GPZ1000RX, KAWASAKI ZX-10, KAWASAKI ZZR1100/ZX-11, KAWASAKI ZRX1200 Daeg, KAWASAKI ZRX1200R, KAWASAKI ZRX1100, KAWASAKI GPZ900R, KAWASAKI GPZ1000RX, KAWASAKI ZX-10, KAWASAKI ZZR1100/ZX-11, KAWASAKI ZRX1200 Daeg, KAWASAKI ZRX1200R, KAWASAKI ZRX1100, KAWASAKI GPZ900R
Although I tried to replace it.
Oil started leaking from the OEM, so I replaced it.
Yeah, Parenthesis is bad.
If my friends saw it, I'm sure they would. You're about to miss the Screw. I'm sure they'll say, "Oh, no, we're not going to do that.
For what it's worth, if Bolt Nut were also Black, it wouldn't stand out so badly.
View detail
Fits: KAWASAKI Z series, KAWASAKI Z series, KAWASAKI Z series
Very high quality funnel net for Yoshimura TMR-MJN40 carburetor
Been looking for the funnel net or dust cover for my yoshimura tmr-mjn40 carburetor for quite some time. The ones we usually have are of low quality. found these on webike by PMC performance, the built quality is very high with right fitting rubber to suit the standard yoshimura aluminium funnel. I went for the bronze netting (slightly more expensive) but it is well worth the money! very beautiful and functional. highly recommended! View detail
Peace of mind
Although my Z900RS has its own temp gauge I wanted a second point of reference. This gauge gives me peace of mind and looks great compared to the bikes stock plastic oil filler cap. I also get a more accurate reading from this gauge compared to the digital, bar style reading on my bikes dash. View detail
It looks better
I bought this product instead of the 3DAir Filter I had been using for vehicle inspections because it was falling apart over time, and I had been buying a new 3D one every few years (roughly once every two vehicle inspections?). I use this product in combination with PMCOvalFilter (154-527). I looked for it but could not purchase it due to undecided delivery date. I personally think the appearance is simple and better than YOSHIMURA (a happy miscalculation). Please note that depending on the car model, it may be necessary to secure space behind the carburetor. View detail
Fits: KAWASAKI Z2 (750RS/Z750FOUR), KAWASAKI Z1 (900SUPER4)
Purchased for Kawasaki 650RS (W3)
The two die-casting parts other than the main switch will not be used for the W3, so they are useless, but it is important to have new parts for a 50 year old vehicle. Since the main switch is being replaced, the key will of course be changed and the old key will no longer be usable. View detail
No problem, but 2000 yen for this... I have a feeling that this is a good idea.
I am satisfied with the feel of the product, but I feel that the cost is a little low.
I wonder if Spacer could not have been made with cheaper Material.
It's out of sight...
Well, there is absolutely nothing wrong with the product itself.
View detail
Necessities
Installation was easy, with no particular troublesome work required. View detail
Fits: KAWASAKI Z1 (900SUPER4), KAWASAKI Z1-R/Z1-RII, KAWASAKI Z1000, KAWASAKI Z1000 MkII, KAWASAKI Z2 (750RS/Z750FOUR), KAWASAKI Z750FX, KAWASAKI Z900 (KZ900), KAWASAKI Z900 (KZ900), KAWASAKI Z2 (750RS/Z750FOUR), KAWASAKI Z750FX, KAWASAKI Z1000 MkII, KAWASAKI Z1-R/Z1-RII, KAWASAKI Z1000, KAWASAKI Z1 (900SUPER4), KAWASAKI Z900 (KZ900), KAWASAKI Z2 (750RS/Z750FOUR), KAWASAKI Z750FX, KAWASAKI Z1000 MkII, KAWASAKI Z1-R/Z1-RII, KAWASAKI Z1000
Purchased to protect stud bolt of Exhaust System
I purchased this for Stud bolt protection as it was not originally included. I recommend it for its accuracy. View detail
Fits: KAWASAKI Zephyr 750, KAWASAKI Zephyr 750
The quality is good and the cosmetics are quite good.
The footing does not change much, but it is good that it can be popped on and gives the feel of an old car.
The price is surprisingly about half that of OEMSeat.
I would buy it again with a different Design (lol).
Also, note that the seating position is about a few centimeters back, so if you feel the Handlebar is too far away, be careful.
View detail
It is as good as OEM Product, and I am very thankful that OEM is discontinuing it.
This time, it had been more than 10 years since the last replacement.
Preventive replacement.
During this time, carburetor adjustments were made and the carburetor was replaced with a Big carburetor.
Wire was also loaded quite a bit, but I could not find any more Damage, although there was some stretching.
Manufacturer discontinued, but thank goodness it is available!
View detail
Fits: KAWASAKI Z1100 (KZ), KAWASAKI Z750-D1 (KZ750D), KAWASAKI Z900 (KZ900), KAWASAKI Z1000 (air-cooled)
Oil seepage from oil pan
Oil seepage from the oil pan was found, so it was replaced.
No problem in use.
View detail
Fits: KAWASAKI GPZ1000RX, KAWASAKI ZX-10, KAWASAKI ZZR1100/ZX-11, KAWASAKI ZRX1200 Daeg, KAWASAKI ZRX1200R, KAWASAKI ZRX1100, KAWASAKI GPZ900R, KAWASAKI GPZ1000RX, KAWASAKI ZX-10, KAWASAKI ZZR1100/ZX-11, KAWASAKI ZRX1200 Daeg, KAWASAKI ZRX1200R, KAWASAKI ZRX1100, KAWASAKI GPZ900R
Gorgeous piece.
The machine work is phenomenal. The fit and finish is amazing. It's a bit expensive but well worth it in regards to build quality. Love it!! View detail