Reviews
Stud bolt is short
Stud bolt was too short and I was not comfortable with the installation.
If we tightened them down firmly, they would have more usable length than they appeared, but I still felt uneasy about them.
Is it not supposed to be installed in Damperetc.OEM condition?
There is no such explanation at all, though.
I've dumped my Gold down the drain.
I was also annoyed by the ”Triple tree” in the Instruction Manual.
View detail
Difficulty in quality and inspection system
I returned the item because I received an item that was doubtful to be new.
Below is the contact information from Support.
We have reviewed the images you provided. 。 The condition you described is probably due to stain from the mold release agent used during the molding process. 。 Unfortunately, this degree occurs in almost all of them. 。 I think it would be possible to clean it with a neutral detergent, etc. to clean it to some extent, but if you request something that has nothing like it, I'm afraid I cannot respond to your request. 。 If you are not satisfied with the quality, we will be happy to accept your return."
“The answer was that it occurs in almost all of them” but at least it wasn't in the ones I have purchased in the past.
It may be hit or miss.
It might be better to check and buy in a real store since it is a place that is always touched and seen.
View detail
Importance of in-place information
The product itself is fine. The color is also good, close to Fork.
I bought it without paying attention because everywhere I looked it said that 187mm was good or best for jc61etc. groms, etc. ….
With this length, the clamp can only be attached to the rounded part of the handlebar. It is possible to attach the clamp by forcibly tightening the screw. It is indeed a good parenthesis in terms of position.
Personally, I think that it would be better if the clamp and handlebar were mounted on the flat surfaces of each other, so that they are rigid and the handlebar is not damaged. I think this is a good idea.
It was an expensive study.
View detail
Petroleum smell!
I'm sure others have written about this, but it is a strong petroleum smell. It filled the room and I had to take it outside to the Small store. Regular washing did not improve it at all, so I soaked it with baking soda that I found on Net. If that doesn't work, I will wash it one more time with Sesqui Soda. If that doesn't work, I will throw it away.
By the way, when I rubbed lukewarm water with baking soda and laundry detergent, the water became Black cloudy.
View detail
Fits: KAWASAKI Ninja1000 SX, KAWASAKI Ninja1000
aiueo-o (Chinese dictionary arranged by rhyme, displaying the meanings of kanji)
First, waiting for goods to arrive. (3 months)
I had to wait 3 months for all of them because I bought other products with them.
I was going to order a split order, but that screen doesn't appear.
I don't know because the product hasn't come yet. I would like to Cancel my order.
View detail
Things are good.
First, the quality and texture were very good.
I was concerned because I was told it was an imported product, but there were no strange rattles or uneven coloring, and I think the surface treatment is beautiful.
but it does not go on as it is.
The first thing to do when taking it out of the box is to measure the Clamp section.
This is something I always do when I purchase external parts from Netetc. before I start the installation process.
We don't want to be in trouble in case there is a Size mistake.
In the NINJA2 Helmet 50R and 400, the OEM handlebar is placed on the top bridge, and the front fork is protruded by about 20mm.
I am sure the Owner will understand this.
In contrast, the height of the Clamp section of this product is approximately 30mm.
You get the idea.
The front fork protrudes about 20mm in OEM condition, while the Clamp portion of the product is about 30mm.
If you want to install it, you will have to increase the protrusion by 10mm.
Unless you have changed the rear suspension or lowered the ride height of the rear with Lowdown Link etc., it will have a large effect on handling if the front fork sticks out 10mm, and in some cases, it will be very dangerous if the fork sticks out too far. (I know it depends on the individual's perception.) 。
Since I have no plans to lower the ride height, I decided to ask for a return since I have not installed them, even though I took them out of the box.
View detail
Fits: YAMAHA XJ650, YAMAHA XJ750, YAMAHA XJ650, YAMAHA XJ750
A-Top Carburetor Joint XJ650
It cannot be installed because it is facing the wrong way. View detail
It's supposed to be brand new.
After installation, the screw part is popped from the root. (Polish)
It's a handshake.
I need to buy another one.
It's off carburetor, so it's still good.
View detail
Difficult to install.
Unfortunately, it is difficult to install on the DL1000 V-STROM800.
I've been saved a lot by SEROW, so I have excellent credit.
View detail
Purchase Comments
Purchased in October
There was a little bit of Rose Throw when the device was used.
Currently about 2,000k since use.
Rose tsuki is getting better and better.
It becomes intense and not stable at all.
It went back and forth from 500 RPM to 2,000 RPM, and so on,
Slow Jet、
Main jet.
To be confirmed.
Used with scratches on the Driver that can be recognized as a "Hadrill".
Also
Due to lack of spare Jet
To be purchased separately.
It was a failure.
In products that I can recommend
None
You should not make a purchase based on price point alone.
View detail
Fits: HARLEY-DAVIDSON SPORTSTER (with CVCarburetor), HARLEY-DAVIDSON BIGTWIN 88-06
This Shop ships very old inventory.
I received the product, but the Gasket was deteriorated and shattered. It was a condition peculiar to long-term storage.
I bought an air cleaner from Webig before, but the rubber of the air cleaner was pushing stiff due to the symptoms of long-term storage.
Are foreigners managing the merchandise and shipping?
They send it in too bad a condition that you can see right away.
There have been two in a short period of time, so I don't count on this Shop anymore.
Please take care of yourselves.
View detail
Cannot be installed.
19 Corsa in Bembo I purchased a corta Master Cylinder at the same time, but since the Master Cylinder is not a RACING Cylinder, the mounting angle does not match the handlebar.
I bought it for Bembo without any doubt, but it was a fit for NISSN, but the description only says Bembofor Racing, which is a pitfall for a manufacturer.
We will post our impressions so as not to make the same mistake.
View detail
Fits: HONDA C125, HONDA C125, HONDA Z125M, HONDA Z125M, HONDA Z125M, HONDA Z125M, HONDA C125, HONDA C70, HONDA C70, HONDA C70, HONDA C70, HONDA GROM125, HONDA GROM125, HONDA GROM125, HONDA GROM125, HONDA GROM125, HONDA GROM125, HONDA GROM125, HONDA GROM125, HONDA GROM125
HondaOEM?
I ordered OEM Parts and they came in a Small bag with Zipper instead of the usual Honda bag. View detail
Fits: HONDA GORILLA, HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA MONKEY BAJA, HONDA MONKEY, HONDA MONKEY, HONDA GORILLA, HONDA MONKEY, HONDA MONKEY, HONDA GORILLA, HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA GORILLA, HONDA GORILLA, HONDA GORILLA, HONDA MONKEY, HONDA MONKEY, HONDA MONKEY
Condensation is ManufacturerSpec.
The review said there was condensation, but there was no mention of it in the product photos or description. However, when I received the product and looked at the package, it said in large letters that condensation occurs. I don't think you can just buy a product without knowing about it and then ask for permission. Also, the temperature is indicated to be up to 200℃, but I thought it would burn out before that. View detail
Fits: HONDA Dax125
Gasket does not fit and has not been installed.
The product page said that the parts were required separately and that the Gasket could be purchased from here, so I purchased it from that page, but the part number was wrong and I could not install the Exhaust System. View detail
Fits: HONDA CBR1000RR-R, HONDA CB1100RS, HONDA CBR600RR, HONDA VFR800F, HONDA VFR800X, HONDA CBR1000RR, HONDA REBLE1100, HONDA REBLE1100, HONDA CB1000R, HONDA CB1000R BLACK EDITION, HONDA REBLE1100, HONDA REBLE1100T, HONDA REBLE1100, HONDA REBLE1100T
Photos and other products have arrived
It is different from the specifications of the first picture and content. When they explain it in a confusing way and try to return it, they ask me to pay for the delivery fee View detail
Don't touch it out of curiosity.
Mounted on NINJA2 Helmet 50RR.
The wall thickness is considerably thinner than that of the OEM, but the stiffness and strength are not hampered by this.
However, I would recommend that only those who are capable of machining Carbon should purchase this product, as there is a hell of heavy machining waiting for some products.
I mean, it's so much more difficult to process than FRP that I can say to anyone, I don't recommend it.
View detail
Cannot be folded
It is fixed with Screw lock and cannot be folded.
No OEM compatible quality.
View detail
Fits: HONDA CRF250L, HONDA CRF250L RALLY, HONDA CRF250RALLY S, HONDA CRF250RALLY, HONDA CRF250L RALLY, HONDA CRF250L
Too inaccurate to install
Right SideBracket was too inaccurate to install.
I managed to install the Left Side, but could not use it as a product at all, hence this rating.
View detail
Poor quality
Shape Design is fine. Paint is rough and muddy, FRP is 5 times rougher than I expected. I would rather buy a more expensive one. I want to return it. I'm not complaining about the color or anything, I just wish they would have at least made the paint smooth. I am sorry. View detail