Reviews
I would have been fine with OEMFender...
When I went through the OEM Fender to get a belt to fix the Seat bag, I found that the OEM Fender was plastic (not weak, but it would flex), so I decided to use the Fender Eliminator Kit, which was also inexpensive.
Probably the most difficult part of the installation is the removal of the OEMFender.
Instruction Manual does not have instructions for removing OEMFender.
However, if you are a do-it-yourselfer, you can remove the Rear Fender when you insert the ETCCard, so you may not have to do so much work (^^;)
The construction itself is solid, so the seat bag can be securely fastened to the belt.
I feel like it could be a little more behind the License Plate, but I am satisfied with the strength of the product.
View detail
On the GSR750
I chose this product because I like the clean Rear view. I like that it is not cluttered, but it may feel cheap to some people.
The process was easy and uneventful.
The LED Lamp is also beautiful, but the projection to attach the Lamp is a little too large.
If we drive long distances in the rain or on roads with floating dirt, our rear bags and backs will get dirty, but this is unavoidable.
The price is low and it is a good product!
View detail
Mounted on Gsx250r
Mostly satisfactory Level. Dry rating, a little bit of the part to be fixed to fit the body of the car is a little Quantity.:Pair (for Left and Right) There was a Gap. It is not visible unless you look through it, and there is no problem installing it. It is not too difficult to install. Included Parts:I think it is a satisfactory Level. View detail
Fits: KAWASAKI ZX-14R, KAWASAKI ZZR1400 (ZX-14)
Simple and good angles
Simple and easy to install. The angle is nice, but it can be bent in a vise for freedom.
I hope the price is a little lower since it is Simple.
View detail
Fits: YAMAHA Bolt CSpecifications, YAMAHA Bolt, YAMAHA Bolt
Compared to other companies.
I bought this one compared to the other company's product based on appearance alone, but I actually had to purchase the Reflector separately, which is a bit of a hassle.
However, the good thing about these parts is that, like the OEM, they cover the various wiring parts and completely hide them when viewed from the reverse side. This effect will not show up in a short period of time, but I think it is highly effective in protecting the wiring from waterproofing and damage caused by possible contact with the tires.
View detail
Fender Eliminator in HURRICANE
[How is it used?
The size is perfect to the point where the cover of the Normal blinker fits.
Easy to install and work with
Was the one you received as per Image?
Street Image
Was the installation difficult?
Easy to do if you have a Driver and Ratchet tool.
How was your experience with it?
Satisfied with Refreshing and Sharp around Fender as intended.
The material is aluminum and painted, so it looks simple but is solidly made.
[Included Parts:were they on?
with Exclusive Harness・Led License Lamp
[Was there anything that disappointed you?
When the Led License Lamp is installed, it comes into contact with the Stop-lamp, which causes vibration.
Concerns about LampCover cracking.
Items/Reflector that should be purchased together must be purchased and installed
View detail
It's fine as it is, but...
The NORMAL Fender was unnecessarily long, and although it looked like a modern motorcycle, I felt that it was too bulky.
Active has a low Blinker position but the License Plate Light looks good, while HURRICANE has the best Blinker position but the License Plate Light is too visible.
I chose "Made by HURRICANE", giving priority to the large blinker position as an impression, because I thought it would be better to make a cover for "Numberberetc.
During installation, the bolt that holds the OEMFender was fastened so tightly that I wondered if Honda's assembly line was Torque controlled....
Reflector is not included and must be purchased separately.
I purchased a KITACO Reflector.
In the OEM, it is boxed, but in the Fender Eliminator Kit, the wiring is exposed.
As mentioned in the Title, since it is not face-whitening to install it as it is, we bought a CBR400R Fender, cut it down and dared to put a Fender on it to make it look like an OEM Fender.
Also, I didn't like the above bare surface, so I made a winding Guard from Rear tire.
The accuracy of the parts, including the position of the holes relative to the car body, was solid.
It is a good product.
View detail
Stylish
Stylish and parenthesis. On the other hand, the GSX-S1000 has a short rear cowl, which causes a lot of mud splashes when riding on wet roads, and when riding in a large rainstorm, rainwater will keep hitting your back. The Reflector is also a Quantity:I'd appreciate it if it was Set. View detail
This is a recommendation for those who value cost.
[How is it used?
I installed this on my 2012 CBR1000RR SC59 late model.
Was the one you received as per Image?
It was just like the picture on the product listing Page.
Was the installation difficult?
I think the difficulty of installation is quite low.
The OEMFender needs to be rosed, but I was able to do it easily by floating the claws.
How was your experience with it?
I have the impression that the price is right for better or worse.
If you are particular about the shape of the Tail, you might want to choose a more elaborate shape made by another company.
View detail
I want Reflector on it too.
I don't like NORMAL Fender of ZX-10R.
So, I considered making a Fender Eliminator and went to various manufacturers.
As a result, I chose HURRICANE's Fender Eliminator Kit, including the cost and design.
I bought it because I thought the price was fairly common.
Installed as soon as it arrived.
I'm a novice, but I was able to install it quite easily because it came with an instruction manual.
The trouble would be when you remove the long bar that holds the current Fender in place.
It didn't come off at all, so I hit it with -Driver and Hammer to remove it.
On the downside, as others have written.
There is no Reflector, so you will need to purchase them individually.
In addition, the angle is docile, and the board Gold side where LED Light is installed is
Is it that there is a little gap between the vehicle and the body?
Other than that, no complaints.
View detail
The OEM Mudguard wasn't cool, so I replaced it!
The OEM Mudguard wasn't cool, so I replaced it!
Rear area has been refreshed. (^-^)
*ReflectorLicense Plate Bracket is required separately!
View detail
Up type muffler beware!
It is a universal blinker. When I installed it, I was relieved to find that it is not allowed to use a universal blinker, because it has a small blinker.
When I installed it, it hit the Yoshimura Exhaust System Up TypeR-77SCYCLONE and I had to change the blinker to an ultra-small blinker.
Also, the gap between the License Plate and the Exhaust End is only about 5mm.
The Down Type Exhaust System should not be a problem, but the Up Type muffler should consider the Blinker's Large size before purchasing.
The product is easy to install and cheap.
But in the end, I ended up paying the same amount of Gold as the more expensive Fender Eliminator.
View detail
Looks neat!
I purchased and installed it in order to refresh the GSR750's gears
I'm happy with the cost and the build quality
Personally, I think it would be better if the angle of the Number can be adjusted
I modified another car's Normal fender for rainy day driving
If you don't know about the GSR750, I think it looks like a NORMAL
View detail
All in all, I think it's a product that is worth the price
This is a Fender Eliminator Kit for the GSX-S1000, order it now I haven't received it yet, so I don't know how it feels or the texture of things etc
As you can see in the product description image, the position of the blinker is a little bit far from the number, so I'm worried about it Some of you may be
Also, you need a reflector, so it would be nice if you could include one with this package
View detail
Fits: SUZUKI GSX1300R GSX1300R HAYABUSA(GSX1300R HAYABUSA)
Clean around the rear!
GSX1300R HAYABUSA 10 years old, installed for use in North America
It's pretty neat around the rear! I don't like the raggedy OEMRear Fender, and the Fender We recommend "Made by HURRICANE" which is the cheapest Eliminator Kit available It is
Installation is easy if you can remove the rear cowl, Couplet-on for easy installation It is
In my opinion, I would have liked the Number angle to be a little higher
It also comes with a License Plate Light, but it's not that bright
It doesn't have a Reflector, so you need it separately for inspection
Overall, the Rear area is cleaner and the Number is angled, which makes it look very It gets better
View detail
That's good!
I wanted to Refreshing Rear, which was feeling heavy But I don't want to spend that much Cost
You can use the OEM Blinker and License Plate Light as it is I'm glad I did
I'm satisfied with the image
View detail
Fits: YAMAHA Bolt CSpecifications, YAMAHA Bolt, YAMAHA Bolt
It's all clear
I wanted to make the back view of BOLT a little bit better for parenthesis, so I installed it It is the type which does not remove the Stop lamp of NORMAL Since the external LED stop lamp is not reliable, I was looking for the type that makes use of NORMAL Because I installed it without reading the Instruction Manual, it is Normal Because it became the installation with removing all the fenders, it had some difficulties I think this is a good product to protect because it also hides behind the back Just replace the NORMALCoupler and the License Plate Light It was made brighter by LED View detail
It's easy to install with a small ball
I installed it in the old Grom
Installation was easy and OEM Blinker was attached without problem
Although there are also explanations, Red's Reflector and triangle magazine Sealetc. I need to prepare myself and I do not have a Bracket so I bought another Bracket for Reflector and since the Wiring part of the Reverse side is all out, it would be better to think about something Waterproof measures
Texture was good and I was satisfied.
View detail
Installation is easy
BMW I attached it to S1000R 2017 without problem
It is easy because it is wearing with basic Bolt 3 books
License Plate Light is also safe because it is OEM use
The accuracy is also high in the simple form but it will be saved if you can suppress Cost a little more
View detail
It's cheap. Installation is ... ,,
About License Plate Light This price is cheap.
I am satisfied with appearance also Refreshing and OEMBlinker without incongruity.
As for installation, Instruction Manual is a piece of simple paper. It was pretty much Large..
I think that it will be easier if you do not weld the Fender with Screw and Nut, but weld the Nut part etc..
And since Bracket in the License Plate Light part is a little Large, I think that I refreshed more if it is more compact.
I also recommend ordering the Made by HURRICANE Reflector.
View detail