Reviews
Easy to use
The rear wheels can be used without difficulty, but the front wheels cannot be used. The front wheels are gradually shifting, perhaps because they are stuck in place. View detail
It's well made, but....
Installed on High ace3 late model, WideMiddle roof car.
It looks and feels solid, but I can't get the Hook to work.
I had no choice but to use Tie Down's Sub belt.
View detail
How about one for Garage?
I purchased this product for the first time for Chain Maintenance.
I was nervous when I put it up for the first time, but Quantity was there without a hitch!:Set is ready.
It is so convenient that I wish I had introduced it sooner.
I am satisfied with the quality of the product, but I have one point,
The hook part was bare gold and it looked like it might scratch the Swing Arm,
I covered it with Fuel Hose, which happened to be available.
Other companies' MAJOR products have already taken countermeasures in this area, so please check this when purchasing.
View detail
A little processing was required.
The inner diameter of the Adapter seemed to be a little small, so I could not install it, and since I did not want to cut down the STANDBODY side, I used a Leutor to cut down the inner diameter of the Adapter I purchased this time so that it would be large enough to fit. Although I was disappointed with the product itself, I am glad that the Adapter only was sold, even if it requires a little modification, because without it, I could not STAND-UP safely. View detail
Needs a little work.
The inner diameter of the Adapter seemed to be a little small, so I could not install it, and since I did not want to cut down the STANDBODY side, I used a Leutor to cut down the inner diameter of the Adapter I purchased this time so that it would be large enough to fit. Although I was disappointed with the product itself, I am glad that the Adapter only was sold, even if it requires a little modification, because without it, I could not STAND-UP safely. View detail
easy
I bought this for the purpose of applying ChainGrease and polishing the wheels, and it works well considering the price, although it does require a bit of effort to rotate the Tire. View detail
A little high for Minimoto use.
I was wondering about the step up Type,
Foldable and light enough to be left in the car.
I bought this one so that I can
The height is a bit high for Minimoto use.
Lifting and placing the Motorcycle is quite Large and strange.
You have to lift it up tight when you put it on.
The non-slip Rubber bites into the Under Guard.
STAND is running away from us.
If the leg opening angle can be changed and the height can be altered.
I thought it was nice.
By the way, Rubber smelled like petroleum at first.
After a week or so, it stopped bothering me.
View detail
The construction is good.
I think the construction and texture are good.
However, a little caution is required for use with the z125pro.
It is slight, but it hits the lower side of the Cowl around the Headlight when Lift up.
It doesn't hit me so hard that Cowl might crack, but I am concerned.
We are in the process of fabricating a color or something to address the issue.
Therefore, I gave it a rating of 3 stars in my environment of use.
Functionally, there is no problem at all, so if it is a car model that does not hit anywhere on the body of the vehicle, it is perfect.
View detail
Sharp Handle with care
I'm not used to this, so I had to cut the Outer tube with this one.
It needs to be used gently.
Material without changing shape:If there were Plastic's, I'm sure they would have enough use for it.
They won't be able to cut it down.
Well, I'm not happy with it, but I guess I'll keep using it.
View detail
Fits: Others NISSAN CaravanNV350, Others TOYOTA High ace200 series
Space would be a bit wasted.
I use it on my Narrow High Ace van. I bought the additional type for the Rear Sets because the full size motorcycle could not fit on the Rear Sets unless it was stacked diagonally.
With Rear Sets that can be shifted in front of SUPERgl, it would probably go straight in even without DirectKit.
View detail
Usable for Chain maintenance but unstable
The Lift with Damper is useful because it is the only one that allows low-floor trail bike maintenance. However, the Motorcycle shakes considerably when it is mounted. It is good for chain maintenance or temporarily lifting the front and rear wheels, but not for removing the tires to change the balance to a large one. However, it is not possible to change the balance to a large one by removing a tire, for example. In such cases, the Fixed Type STAND is the best choice. View detail
STAND
I used to work with Jack on it, but now I can work without anxiety.
Personally, I'd like to see Tie Downs and lashings included.
It could be used in a variety of ways.
View detail
For Torque wrench use
The DRC Sprocket bolt was loose and I wanted to use the Torque wrench to tighten it just in case when I replaced it with an OEMBolt nut. I bought it because I wanted to use the Torque wrench to tighten the Sprocket bolt nut when replacing it with the OEMBolt nut, just in case. View detail
Convenient
I use it on my SEROW 250.
If you forget to check the minimum ground clearance and use it in SEROW, it is a little high (lol).
So I lifted it up a little and put it on.
This is the first time I've bought one of these, and it's pretty heavy when you lift it up.
I found it a little easier to use the Image to apply the Center Stand.
View detail
Be careful with thick Mirror at the root.
It's light and looks weak at first glance, but it's strong enough that it won't deflect even if you put a lot of pressure on it.
However, it didn't stick with my Mirror because it was incompatible with it, so please refer to it.
Ideas is good because you can turn it over and it can go either way.
View detail
Affordable.
This is a great way to improve the atmosphere of your garage, protect the floor, prevent scratches from the STAND directly hitting the concrete, etc. When the STAND is not in use, you can use it as a place to place parts during maintenance to prevent them from rolling or flying around. If you want to use it as an underlay for STAND, it is limited to MXSTAND or a simple type of STAND (purchase their product at the same time) that is lifted by applying it to the Under Guard of Off car. If you want to use Front StemSTAND and Rear StemSTAND at the same time for serious maintenance, it is better to buy Full size RACINGMatte. View detail
Cosmetically, it's alright. The only thing I wish I'd known before I bought it was that ……
I bought this to service my Off car.
When I bought it, I was worried about which one to use with HC2STAND of DRC, but I chose this one because the price was cheap.
It takes quite a bit of hang to lift, or I think that point is the same for all Off-road stands.
The only point is that this product does not have a lock function on the top panel, so when you lift the product, the body is not in quantity.:Pair (for Left and Right) It will move to the It is possible to take measures by fixing it with something, but I think that it is a matter that I want to know before I buy it if possible.
View detail
Also recommended for Helmet's Display!
I recommend this to anyone who wants to display or store their helmet on the wall. I used 4 of these to hang my helmet on the wall like a showroom. View detail
I'm worried about the wound.
I thought the U-Hook was better than the L-Shaped Bracket and bought it.
The U-shape is more secure and easier to fit.
With the L-shape, you have to make the motorcycle somewhat horizontal to hang it.
I'm concerned about the BALI at the end because Bracket just pulled it out with PRESS.
I didn't want to damage my motorcycle with the Bracket, so I wrapped Vinyl Tape around it.
I want you to wear at least Cushion rubber. I wish you could wear Cushion rubber.
View detail
Well, it's something I wish I had.
I bought it for cleaning the chain on my off-road motorcycle.
To be honest, the rubber on the receiving end of it is easy to tear off and the price is right.
Since it is a Universal Product, where is Quantity:Set the rear tire to float or
It's quite inconvenient.
This would be a roller stand or a regular hydraulic jack.
You might as well buy it.
View detail