Reviews
Connection
Type 110, Cable branch, used for connection.
Male、FemaleQuantity:Set and a little extra in number, it was just right for a spare.
View detail
disconnection
Since the Cable came off during Connector removal, it is used to crimp the Cable to the terminal again.
We were able to use just the right number of pieces.
View detail
defective contact
It is used for reassembling due to poor contact of Cable.
I wish there were a certain number of pieces, but I don't think the cosmetics are very good.
View detail
Can be used as Repair Parts in case of damage!
[How is it used?
I found it damaged when replacing the Tail lamp on my car and purchased it for effect.
Image by Quantity:1 Set of 2pcs.
How was your experience with it?
Just insert it in the same way as the NORMAL. The replacement of the damaged one, which was unstable due to rattling, can be fixed firmly.
The shape seems to be shared by Honda and DAIHATSU vehicles.
How did it compare to other products?
I don't know because I have not compared other products.
[Points to note]
It is better to insert slowly and without force.:Plastic, so it is easily damaged.
Other items that would be helpful
Whether there are Included Parts:/ Items that should be purchased together/Opinions and requests to the Manufacturer
View detail
Cheap and solid
Used in Step WGN Maintenance of Transporter.
I thought it was slightly difficult to put in and out the Bracket, which determines the height, but if you apply Rub or Grease, there is no problem.
It is cheap and has a sufficient load capacity, so I think Sunday mechanic is good enough.
I should have bought the Rubber adapter (sold separately).
View detail
For ZX-14R Low beam H11
A little expensive, but installed before vehicle inspection
Heat sink is large, so I think it will be a good choice for your car model.
And since the Unit is a separate unit, you can't use it in a car model that has a lid on it.
Double-sided tape the Unit to the Frame near the Stem as shown in the photo.
When I put it on and put the Connector on top of it, it didn't interfere anywhere.
The heat sink will be hot, so if you go around it without touching the wiring
It just happened to look like this
It's bright and no complaints but it's expensive. Low beam for car inspections, so this year is not relevant.
View detail
You can also grab LimitMotorcycle's Battery terminal.
Purchased because I am good at raising Battery.
The smallest terminal of the battery for LimitMotorcycle can also be gripped depending on its shape.
Monotaro's JumpCable has been bumped out of Clip's Crimp, so I'm hoping for more durability in the future.
Also, I'm glad that it comes with a Case.
View detail
Fits: Others 200 series High ace S-GL
Recommended for all those who want to make the most of the luggage compartment in High ace.
The 200 Series High Ace does not have a luggage rack in the luggage compartment, so items such as racing suits and changes of clothes that need to be hung (or hung out to dry) must be hung from the Assist Grip on the 2nd row Seat.
So, this product allows you to hang things in the luggage compartment.
By making it easier to place racing suits and helmets in the luggage compartment, along with motorcycles and tools, the entire second row seat can be used for other purposes, which is very convenient. It is also good that there will be more places to hang Hooks for securing luggage in the luggage compartment.
The main drawback of this product is Drill teeth directly against Body." I think this is the part that is the most important. The task itself is not difficult, but this The Spiritual Hurdle." is unusually high, and the average person would hesitate to use it.
The distributor also has an installation video on its website, which shows a large amount of Washer on the teeth to seal the Drill's excessive penetrating force, but the average household does not have such a large amount of Washer, and not many households have 10mm Drill teeth in the first place! I don't think many households have 10mm Drill teeth to begin with.
In the course of this work, we considered purchasing a large quantity of washers to cover the drill teeth, but they are surprisingly inexpensive, and it is unlikely that a large quantity of washers will ever see the light of day again. Therefore, we prepared a 20mm PVC Pipe (about 100 yen per meter) and used Washer only at both ends to adjust the length for Body processing.
The work itself is not difficult and can be installed in less than 30 minutes.
Lastly, although the product may have been developed with a lot of ingenuity, I still cannot shake the feeling that it is relatively expensive.
View detail
It is both light and strong.
I bought a new Transporter, so I bought a Ladder rail to go with it. (Lamp) I was looking for a product and found this product and purchased it.
The deciding factor is the length when folded.
The 150 cm short length is not collapsible and remains long.
However, with this 180cmMODEL, the length can be reduced by about half by folding it.
The small size of the Transporter was EXACTLY what I needed to save a little space.
The hybrid structure of resin and gold seems to be the right material for the right job. I was impressed by the balance between lightness and durability. In my case, the load capacity is sufficient because my motorcycle is only a light off-road vehicle or CUB.
The quality and price are in line with each other, and the cost performance is as good as you would expect from a DirtFreak product.
View detail
Awesome Product!
I often travel 3+ hours to a riding spot and usually have the bike strapped down, with the suspension compressed the whole ride there. It DOES keep you from reefing down on the fork springs so tightly and makes it more stable when hauling. Not to mention all the pressure blowing out your fork seals.This keeps that from happening. A must buy to keep your shocks healthy all season. Plastic there's no danger of scratching fork legs.round portion goes on the tire and square portion on the triple clamp. Plus, the material is A+. Great investment for the money.Good piece of hardware. Only complaint is it could be about 2cm longer. Lastly, it stays in place better than the chinese, which I have actually lost more than once. View detail
For transporter use with light trucks
It can be a Ladder and it can be an Extender.
It is strong and looks good, so I am generally satisfied.
I use it with mxSTAND to load and unload Motorcycle.
View detail
For replacement or spare parts
Quantities for replacement and spares due to out of fuse.:I thought 1 Set of 3pcs. would be a good deal, but since it's Fuse, the cheaper one would have been fine. View detail
Motorcycle or car is acceptable
Ideal for cases where soldering is impossible or where you want to make a removable harness! View detail
That would be handy
It would be useful for electrical DIY.
This is one product you will want to keep in your tool box with Electric Works Pliers!
View detail
For back-up and earth installation
Used for Wiring installation of electric heat.
Emon for peace of mind and the number is just right and cosy.
View detail
5Quantity:Set is also included
You don't have to buy this kind of thing, but you can branch out by making it yourself using two Wiring sticks, but, well, it is easier to have it than not.
This eliminates the worry of wire breakage rather than putting two Wiring together.
5Quantity:I think this price is reasonable for what is in the Set.
View detail
Good job
Fitment is exact & the material used is of good quality. Prevent outside from viewing in. Expensive but totally worth it for the quality & fitment. View detail
It is originally for Vehicle, but can also be used for Motorcycle.
I originally bought it for four-wheel maintenance, but I also use it for Motorcycle Lift up.
Although it is compact, it is designed to withstand 1 ton per pc, so it is stable and Brown.
When I raise the front or rear of my personal Level Motorcycle to remove the Three-Pronged Fork or Swing Arm Link, I use a Side Stand + Pantograph jack instead of a Racing Stand or Front-up Stand (a common technique in the Off-vehicle world, although some people may not be aware of it). (Some people may not know this, but it is a common technique in the off-car world.) However, when lifting a heavy motorcycle on rough terrain, the Pantograph jack alone is unstable and may come off.
In particular, frames without underframes are difficult to capture the center of gravity, and if the crankcase alone is used to support the frame, there is a possibility that the case will crack.
The Pantograph jack is then gently raised by placing it against a crankcase (while curing), and supported by an engine mount using our Jack stand while placing a block or the like underneath. Just like a four-wheeled vehicle. "Uma." The use of the product as a
As mentioned at the beginning, this product is quite Compact and does not take up FootSpace.
It is not the typical folding type, so it will not fold, fall over, or break even if it is set up a little roughly.
It also has a good amount of raising width, and is a very easy-to-use product, even when viewed purely as a Jack stand.
When stored, it can be made into a small size by alternating the two sides.
It is good to have it because it is useful for something in Motorcycle maintenance.
View detail
Cheap and very high quality
Used to move the position of GeneratorCoupler (Wiring extension) in SR(1JR).
I wonder why 1JR has a coupler in that delicate position.
Aside from Type 250 terminals for Coupler, TAB, receptacle8Quantity:This price is quite inexpensive, as it includes a Set.
It is cheaper than KITACO and cheaper than buying in bulk, such as products sold for vehicles. Emon is the cheapest after a lot of research.
There are Chinese CouplerTerminal Sets available elsewhere, but they are not that cheap, and the quality is poor and rickety, so I don't want to use them for the 250 models that are supposed to handle large currents.
Emon is said to manufacture their products in-house at their own FOR JAPAN MODEL factory, so the quality is consistently high and inexpensive. I dislike Emon's Bullet Terminals because they are too high quality and the mating is too hard, but there is no problem at all in this 250 type.
The 250 type for Coupler has a projection on the side of the Male terminal, and the Female terminal has a projection on its back.
This locks the housing, but it is also possible to use a terminal Single Body without housing.
Basically, it is assumed that you have a separate PVC protective Cover, but you can cut the protrusion of the Male terminal so that it does not poke through the protective Cover.
View detail
Used for S1000RR
I was looking for a Wiring near the Tail Lamp with Tail Lamp, but it seems that some Wiring touched each other "ping", and the Fuse flew out, so I bought it.
This may be the first time I have skipped Fuse in any way. I did some research and found that there are so-so types of Fuse in one word.
Size is Exactly.:1 Set of 3pcs., so you don't have to worry even if Fuse skips 4 more times (although it would be a problem if you skip that many times …).
I think it would be good to have it as a Stock.
View detail