Reviews
Fits: YAMAHA WR250R, Others , HONDA CRF250L, KAWASAKI KLX250
Just the right length.
Although I have not had the pleasure of using it on forest roads yet, I tested the actual pull on Garage and found that the thing itself was easy to grip and firm enough to lift the Front. View detail
DRCRear sprocketBolt nut
Bolt nut for the new Rear sprocket.
It is a dedicated product and fits well.
Since it is a component that can easily come off, inspection before driving is a Large cut.
View detail
Might be useful to have.
I think it depends on the way you fall, but in my case, when I fell standing up on a forest road, this helped me to minimize the Damage. View detail
Swing Arm scale is for reference only
As the title says, the scale on the Swing Arm is for reference only.
I was looking at Motorcycle from behind and noticed that the teeth of Sprocket were somehow closer to the body side of Chain.
Quantity in the Swing Arm scale:Pair (for Left and Right) The position of Chain and Sprocket is not good, even though they are in the same position.
The Chain Alignment Tool was used to straighten the Chain, and the alignment between the Chain and the Sprocket was perfectly aligned, and as a byproduct, the Swing Arm scale was set to "Quantity:Pair (for Left and Right) We found that there was a Gap of about 2-3mm in the
If the alignment of the Chain is not correct, it can cause uneven wear of the Tire and damage to the Sprocket and Chain.
This is a Tool of Recommendation for those who are interested in getting ChainAlignment right!
View detail
Fits: HARLEY-DAVIDSON Sportster S, HARLEY-DAVIDSON Pan America, HARLEY-DAVIDSON Nightster Special
Flashing switchCover
Very good!
The switch knob was originally shaped to be far away and difficult to operate for Small Saijapanese with hands, and it was a part that we had to put up with.
Push cancellation was easy and finally Refreshing.
If I may say so, it would be better if there is an arrow or some other prominent mark-like label or paint on the top surface. I applied seals, but the surface is matte textured, so seals tend to peel off easily.
View detail
Easy to install, easy to use, but ….
It is easy to install and easy to use, but it looks tacky when the Bag is not attached. Also, the gap between the bag and the car body is wide, so it looks tacky from the back.
Also, the price of the separate installation kit for the OEMRear carrier is too high.
View detail
Fits: KAWASAKI ELIMINATOR SE, KAWASAKI ELIMINATOR
expensive
Was the one you received as per Image?
Yes
Was the installation difficult?
Easy
How was your experience with it?
Nothing to use, just Screw.
[Was there anything that disappointed you?
price
View detail
For NINJA400R
Installed on NINJA400R.
I was able to do it without removing the cowl, but I had a little trouble tightening the bolt because it was too small.
If the installation had been a little easier, I would have given it a perfect score without any complaints.
View detail
Fits: SUZUKI Gixxer SF 250, HONDA CB1300SUPER BOLD'OR, HONDA NC750X, HONDA CB1300SUPER FOUR, HONDA CRF250RALLY, HONDA CB1300SUPER FOUR SP, HONDA CBR650R, YAMAHA MT-25, HONDA CB1000R, HONDA CB1300SUPER BOLD'OR SP, HONDA CRF250RALLY S, SUZUKI Gixxer 150., KAWASAKI VERSYS-X 250 ABS(17) KLE250D, YAMAHA MT03, Others , SUZUKI V STROM250SX
I thought it would be good for day touring.
The quality looks good, but the capacity is smaller than the picture suggests. The capacity is enough for one day touring. View detail
Fits: KAWASAKI ZX-4R, KAWASAKI ZX-4RR, KAWASAKI ZX-25R
Small modification required
I wanted to improve the grip at a track meet, but not enough to install a race cowl, so I decided on this product.
Weight is approximately 950g, a slight increase in weight from OEM (FRP).
Color because it will get dirty with Rubber replacement.:It is unpainted, but the matte texture makes it feel comfortable as it is.
The installation of the product was partially interfered with by the body of the car. The installation itself could have been done without modification, but we did not want the stress to be concentrated and cause cracking.
Fitting is otherwise good, and the rear end, which had a wide gap in the company's 10R model and seemed prone to water and dust infiltration, is now better aligned.
The attached rubber was already cut, but I beveled it with File because the Edge was going to be damaged.
The installation was a few Bolts, but it was unexpectedly time-consuming due to its location in a narrow space, and I was thinking of switching to NORMAL depending on my mood, but it was such a hassle that I didn't feel like doing so.
Wet type rubber is attached. The gripping feeling is very large, but it is difficult to shift a little while sitting on it because it grips as if it is attached.
The sponge also feels resilient to the touch, but when you sit on it, it feels chica-chic and is not suitable for everyday use.
(It's RaceParts, of course, but I was thinking of using them on a regular basis because they are a pain to replace)
View detail
Fits: SUZUKI V-Strom650 L2, SUZUKI V-Strom650, SUZUKI V-Strom650 XT, SUZUKI DL650 V-Strom, SUZUKI V-Strom650 L2 XT
Engine Guard installed
Installation should not be a problem if you have some knowledge of maintenance.
An Engine Guard was added to protect the engine in the event of a runaway and to mount the Fog Lamp.
View detail
Clean. Dirty. Vivid.
Description used only in DOT 4.0 and 5.1.
5.0 (Silicon-based) not used
[How is it used?
Continuous use from July 18, 2021 to April 21, 2024
・71,299 - 59,896 = 11,403km
Urban, Touring, and Circuit driving events
YZF-R6Front side
Master Cylinder side is R6OEM
Fluid tanks are available from Kawasaki (https://www.webike.net/sd/21984592/)
I think Clamp was something from K-CON.
Fluid Transparent DOT5.1 (https://www.webike.net/sd/24515708/)
FluidBlue (https://www.webike.net/sd/24038239/)
FluidGreen (https://www.webike.net/sd/20443936/)
FluidRed (https://www.webike.net/sd/21585702/)
Was the one you received as per Image?
As per Image with Simple Package, first found in Naps and now also in LycoLand.
Was the installation difficult?
The hose itself is fairly easy to insert after loosening the clamp and removing the original hose by tearing it open. However, it is a little bit large to insert the hose without wetting the inside of the hose with Fluid or something.
Air venting is required for modification of the brake system, so there is some time and effort required to vent the air.
How was your experience with it?
・ [Color] When we say ClearTank. [Color] Unlike the Smoke Fluid Tanks, it is completely [Color] Clear shows the Fluid color beautifully.
Although the Image was less durable than the Black Hose, it is still in use with no rips, cracks, or tears.
The Fluid is not blotchy like the non Fluid-compatible Hose, which was my biggest concern, and the word "Fluid-compatible" is true.
The color of the Fluid is so clear that the yellow tint of the Fluid is very obvious.
Especially with blue Fluid, it takes less than a year for the color to become the color of Tokyo Bay, although it is beautiful immediately after the replacement. (Replaced more than 4 times in 3 years of use)
The transparent design makes it easy to see the climb when injecting from the Caliper side.
The product is relatively new, so even Motorcycle shop owners are not familiar with it. Is this Fluid-enabled?" The situation arose where people asked me "What do you mean?
The feeling of operation cannot be evaluated independently because the Fluid is being replaced at the same time, but I am sure there will be no problem because I can use it without feeling any discomfort.
The Red was probably too bright a red to match the Blue/Silver Motorcycle, and I didn't have a picture of it because I replaced it too quickly.
[Included Parts:were they on?
Hose only, Clamp not included
[Was there anything that disappointed you?
None, as the Fluid colors are nicely recognizable and the durability and feel of the product are absolutely fine.
Although it was unexpected that the discoloration caused by Fluid degradation was too obvious, it is inextricably linked to the desire to clearly distinguish the color of Fluid.
[ITEMS TO BUY TOGETHER
Hose clamp and for ReplacementFluid
DAYTONA's Black Clamp rusted quickly, so K-CON is recommended.
The price is not that different from Black's Hose, and the feel is perfectly acceptable. The increase in replacement frequency due to appearance is not a bad thing when it comes to performance.
Degradation of Fluid [Color] A fun product to add to your selection if you can accept that it is more sensitive than ClearTank.
View detail
sounding good
I can't do it myself, so the person who did it for me said that FrontSprocket is very good, in terms of material and lightness, etc. Rear sprocket can be attached with either a pure normal thread screw or a taper bolt, according to the specs. View detail
Commendation for the first Leather Boots
As for the size, the instep area seems to be made for a large size, so it is better to adjust the inner sole or the thickness of the socks.
Purchase Size:26.5cm
Size of my normal shoes
・RedWing US9
・NIKE 29cm
・VANS 27.5cm
・VANSSlip-on Silencer US10
Leather is soft and (DoctorMartin rank) I think that even people who have only ever worn Sneakers will be able to wear them without difficulty.
The softness of the leather also makes it easy to operate the Shift Pedal and walk on foot while touring.
On the other hand, the softness of the leather should not be expected to immobilize or protect the ankle in the event of an accident.
The side fastener is very convenient for Large and I can no longer wear Engineer boots without the side fastener!
The sales person at the manufacturer said that the magic tape that guards the fastener is not strong, and if you are careful when storing it, for example, by stopping the magic tape, it should last for a year and a half. Also, the manufacturer can repair it.
Since there is not much information available after the aging process, we have decided to post an Impression.
Overall, get used to it as your first genuine leather Boots, get used to doing Maintenance. (Brush to remove dirt, apply Cream, blow up, WaterproofSpray) It would be good for
The sales person at Manufacturer told me that Cream is better as a basic oil, because if I put only Mink oil on it, it becomes too soft.
View detail
Fits: KTM 500EXC-F, KTM 690EDRR, KTM 450EXC-F, KTM 450SX-F, KTM 350SX-F, KTM 300EXC, KTM 350EXC-F, KTM 250SX, KTM 250SX-F, KTM 250EXC-F, HONDA CRF250R, HONDA CRF450R, YAMAHA YZ250FX, YAMAHA YZ450F, YAMAHA YZ450FX, SUZUKI RMZ250, KAWASAKI KLX230R, KAWASAKI KX250, KAWASAKI KX250F, KAWASAKI KX450
To help us help you.
Product Name
DRC DRC FrontStack Belt
Item Number
D6426
Vehicles
Honda CRF125F 2024 MODEL
Number of man-hours
5 minutes
Required Tools
Scissors type, etc. would be perfect.
Why did you choose this product?
I chose this one because with this product, I will be able to get help from anyone in case of Race, etc. I also chose this product because of its low price.
Was the one you received as per Image?
It was exactly as shown in the Image. It was more solid than I expected for the price. I hope someone will see this product and help me.
Was the installation difficult?
Installation was not that difficult.
How was your experience with it?
It is not something that you feel particularly when you are running, but I think you will feel glad that you have it in case of an emergency.
[Included Parts:were they on?
None in particular.
[Was there anything that disappointed you?
None in particular.
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
View detail
Famous Stack Belt
Product Name
TREKFIELD TrekField Stack Belt
Item Number
W-3208-P29696891
Vehicles
Honda CRF125F 2024 MODEL
Number of man-hours
5 minutes
Required Tools
Scissors type, etc. would be perfect.
Why did you choose this product?
I chose this one because I wanted to put a Belt on the Seat to make it easier to move the body when Stacking.
Was the one you received as per Image?
It was just as shown in the Image. I can use this one without any worries.
Was the installation difficult?
It's not particularly difficult, since all you have to do is attach it to the Fork.
How was your experience with it?
The fabric seems to be sturdy, so I think it will be safe. I would also like to try it and see if there are no problems with this one. Also, other people are using it and seem to have no problem with it. I have high expectations for the future.
[Included Parts:were they on?
None in particular.
[Was there anything that disappointed you?
None in particular.
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
View detail
[Color] Smoke Screen
Installation was easy, even for an amateur. With a good density, (in Tokyo) I could see in front of me even at night, the Large size was just right, and the wind hit me not hard at all at 100km/highway cruising. View detail
Fits: HONDA SUPER CUBC125, HONDA CROSSCUB110, HONDA CT125CT110 HUNTER CUB
Front feels lighter!
I changed it along with the Front Disc replacement.
The weight is light, but the front tire feels lighter than expected!
The price is reasonable, so if you are not sure, try to replace it.
View detail
Compact
Used 635mm on ZX10R (19) to install new Crab, just the right length.
The structure is simpler and more compact than the Edge line, which was previously used.
The Crimp section is shorter than the SuEdge for easy handling.
However, the Black part is shiny and not good, so I might have preferred the normal Stainless.
The texture of BlackStainless and the MachineMachine-like appearance of the Edge are better, but I have heard rumors that it leaks a lot.
If I had to choose by functionality, it would be Goodridge.
View detail
Used for SHOEIEX-ZERO
This size is ideal for helmets that do not have speaker holes like EX-ZERO and have no space in the mounting position.
I have used the standard Speaker and the thin Speaker, but the Smallest is the thinnest and the sound quality is the same as the others.
The price is a bit high, so IncomeQuantity:It would be appreciated if the Speaker of the Set could also be selected.
View detail