Reviews
Tidies the wire system on your handlebar
Installation was easy and it can be customed to the desired length. Looks wise, it creates a singular and more neater at the steering area. Material is also sturdy and it stays at the position where you set it. View detail
Exactly to Wiring Protection
[How is it used?
When I installed YOSHIMURAOil Temperature Meter on XJR400R, I needed to run the wiring from the back of the engine to the drain bolt to connect to the sensor, but I bought this product to protect the wiring because it is close to the drive unit. I purchased this product to protect the wiring because of its proximity to the drive unit.
How was your experience with it?
The coziness is like a normal Spiral Tube.
It was thicker than I expected, but within the acceptable range. 2m long, so there is quite a bit left over, but it is necessary when customizing electrical systems, so it is good to have it.
How did it compare to other products?
The Spiral Tube was originally included with the Oil Temperature Meter, but it was a bit thicker than the Spiral Tube.
It would be nice to see a little more Size development.
View detail
Cosmetic Items for DIY
[How is it used?
I purchased DAYTONA's Power Unit D-UNIT+ for my XJR400R.
In this process, the stag beetle terminals were modified to Round Type Terminals, and Heat Shrink Tubes were used for waterproofing and terminal protection.
How was your experience with it?
The product was easy to use.
I didn't have a heat gun, so I used a Chuckerman to apply heat, but the shrinkage was firm.
The quantity is so large that I don't think we will run out of it in the foreseeable future.
How did it compare to other products?
Some products are sold as a single item in 6cm increments, but this product is easy to use because you can cut it to any length you like. Also, the package itself plays the role of reel, so it is easy to store.
[Points to note]
It does not have a clear waterproof effect, so care should be taken where it is used.
Also, the shrinkage rate is not that high, so choose the Size according to the actual Wiring you will use.
One concern is that the package is larger than expected, making it somewhat bulky when stored.
View detail
For SUPER SHERPA.
SUPER SHERPA does not have a hazard switch, so I was afraid when I had to stop for traffic or construction at night on the highway, but now that the hazard switch is on, I can tour with peace of mind. I am really glad I bought it. It's like a good luck charm. As expected, there were some positioning problems with Wiring and Relay, but I managed to get it to fit nicely. It's a ba direct, so you have to be careful not to forget to turn it off or play tricks with it. View detail
usual
I think it is a standard Wiring.
I can't compare whether it is good or bad, as I have only used this one, but I am fully satisfied with it.
I will continue to use it if I need anything in the future.
View detail
KIJIMA Position unit
KIJIMA's Position Unit was installed to convert Gixxer 250's Blinker into a position that always lights up. View detail
Cospa best
After wearing Wiring as a solder, the process is easy and Beauty. View detail
It's good.
I bought it because I just needed a code. It is Emon, a trustworthy company. View detail
Expected heat resistance
The power supply wiring needs to be passed through the side of the engine, and to protect the wiring from heat, this product was placed over the 5ΦColgate Tube because it has higher heat resistance than the ordinary Colgate Tube. When you put the wiring through the Colgate Tube, you can easily put the wiring through the Colgate Tube by squeezing the Tube as described in the Instruction Manual.
The Tube is elastic and fits perfectly to the thickness of the Wiring you pass through, so it looks neat.
After cutting the Tube, it will fray, but this will not be a problem if you fry it with a lighter when you cut it.
I gave it a 4 because of the somewhat high price.
View detail
Easy to use
I have never bought a double cord before, but this time I bought it to install a DriveRecorder in my car. 6 meters were left over and I was going to keep them for motorcycle use, but I had to install them in two cars in a hurry, so I ended up using all of them.
0.75 is the thickness of the wiring cord I often use, and the same 0.75 single is used for playing with the electrical components of my motorcycle. I have never had any durability problems with Emon's Wiring Cords, and I feel that I can use them with confidence. I am going to redo the wiring of my Motorcycle DriveRecorder, etc., so I am thinking of using a double cord to make it reflect. I will buy and use this Wiring Cord again.
View detail
Handy Ring Terminal Lead to Ground Universal Accessories to the Grom
About quality and texture: I am happy with the quality of ring terminal lead from SP Takegawa made from a ring terminal, male bullet connector and small section of wire About the feeling of use: Makes connecting a ground to universal accessories like my temperature guage that is not Grom specific a breeze and there is no premanently cut wires if the accessory is removed in the future. Products to buy together: An electro tap would also be desirable to purchase along side the ring terminal lead so that a power can be provided to the accessory via the motorcycles wiring harness. Difficulty of installation: The process to install takes about 5 minutes, the accessory will need a female bullet connector fitted and simply connect the bullet connectors and bolt the ring terminal down onto a section of the Grom's frame that is free from paint for a good connection. Not difficult to do. Cost performance and comparison with other products: Good costing as you are getting two leads complete with connectors to save you the time preparing these yourself as compared to purchasing all the items individually which will be cheaper if you need numerous leads. About shipping and packaging: The faster shipping options are too expensive for myself so I just have to wait for my part to arrive via sea freight. Webike kept me updated on the status of my order up to when it shipped. The parcel arrived within the expected date range and was well packaged with no chance of the part being damaged. Any concerns, cautions, or advice when purchasing: This is a relatively short lead and if you are needing different lengths search grounding cable for many more options. View detail
Easy to use
[How is it used?
The Heat Shrink Tube I had on hand went somewhere, so I bought one.
I chose this product because it is a sizeφ3.2mm, which is often used in Wiring, has a length of 3m, and is relatively inexpensive.
How was your experience with it?
The required length can be taken out and used immediately.
Heat gun (or writer) The work can be done easily by anyone who has
Shrinkage is not a problem, and Wiring looks great, so I recommend it.
[Points to note]
What is ReelPackage? I was wondering, but you can use it without taking it out of Package.
I opened the Package once without understanding, but please be careful if you are going to use it in the future.
How did it compare to other products?
I've been using it for a while now. (probably Emon's). There was no particular difference between the two.
It is long enough for amateur DIYers, so it is nice to not have to worry about buying more.
【Review】
It is easy to use, long enough and cost-effective.
If you are processing Wiring yourself, you should have one to make your Wiring look better.
View detail
It is used for DIY of the stationary portion of the single seat cover of Ninja250R. Although the thing of plating of the company was used, since it had been divided in vibration, the tougher stainless was chosen. Reinforcement, distortion-proof, a
It is used for DIY of the stationary portion of the single seat cover of Ninja250R.
Although the thing of plating of the company was used, since it had been divided in vibration, the tougher stainless was chosen.
Reinforcement, distortion-proof, and rust-proof are the honor students unique to a stainless, and are high. [ of cost performance ]
Since the hole is made, as soon as it processes it with a bolt, it can treat freely.
While it is hard, what processing is hard to carry out is unavoidable.
View detail
It uses, when changing the present blinker a hazard and with a position.
It uses, when changing the present blinker a hazard and with a position. View detail
When touring with friends, turn on Hazard and stop
It is a good product with detailed instructions and easy installation for those who are somewhat familiar with Wiring. View detail
No problem
08 KawasakiZrX400 and KOSO (KN Planning) Used in combination with Sequential Blinker in
Worked fine.
However, the product description does not recommend the use of other manufacturer's blinkers, so the feeling of self-responsibility is Large.
Installation is easy and should be no problem for those who can install external blinkers, USB power supply, etc. by themselves.
BodyUnit is sober and Large
In the case of ZrX, it can be hidden inside the Bikini cowl, but for Motorcycle without cowl, you may need to make some modifications to store it discreetly.
View detail
Hazard kit
Purchased to install Hazard on 400KATANA.
There is an instruction manual and it was easily completed.
Now I am looking forward to seeing how long it will last.
View detail
For Wiring
In order to perform Wiring, this item is also available in Quantity and Quantity:1 Set of 10pcs., Insulated Sleeve set, I bought it because the price was reasonable.
The Package is in good shape and seems to be crimped and ready for use.
But MEDE. IN CHINA.
View detail
For Wiring
I bought this one because of the number of pieces to do Wiring, with Cover, and the low selling price.
Wiring is simply crimped and connected, so it looks Large sturdy, but MADE IN It looks like CHINA.
View detail
Purchased with Sponge sheet
When repairing an OEMOption engine slider, we decided to replace the sponge that comes in contact with the cowl because it had also deteriorated. The thickness of the double-sided tape is 0.4mm, including the backing paper. 0.4mm
After making a base paper and cutting it out of Seat, I tried to stick Double-sided Tape to Sponge Sheet, but the adhesive strength was weak and it peeled off easily. I tried applying pressure with my fingers to make it stick, but when I peeled off the other side of the backing paper, the double-sided tape body also peeled off. The thinness of the double-sided tape also makes it easy to gap, and the double-sided tape will overlap, so please be careful when handling it.
After attaching it to the engine slider, we left it for 24 hours until it was fully adhered. After that, when I touched it, it was firmly adhered, so I felt relieved for the time being. Immediately after bonding, the adhesive is not stable. Please allow enough time for the adhesion to be stable.
View detail