Reviews
inconspicuous (Compliment.)
The quality is high!
I chose Black to give a sense of unity, but with this size, you may want to use a flashy color as an accent color.
The price is for one, so I think it is a little expensive, but I am satisfied with it.
View detail
inconspicuous (Compliment.)
Perfect Fitting View detail
Mirror Hole Cap
I bought this to hide the Mirror hall as I changed my CB223S to a Bar end mirror.
Note that the quantity is 1 pc.
If you value cosmetics, you can use Homsen Screws or Vinite.
The texture is good
View detail
For off-road motorcycle Mirror Hole Plug
Used for Mirror Hole Plug for off-road motorcycle.
I often remove Mirror when participating in Races, etc., and wanted to prevent mud, etc., from clogging it.
There are many inexpensive Color line nap products, so it would be useful to have a few.
View detail
water (esp. cool, fresh water, e.g. drinking water)
I bought this because I didn't want water or dust to get into the Mirror bolt when replacing OEM Mirror.
They blindfolded me nicely.
View detail
I changed it at One point.
I changed it at One point and became Accent and I like it. View detail
Detachable Cover Cap
I bought this to plug the mounting screw holes for the Back Mirror on my KLX125.
I often go to forest roads with KLX, not only open forest roads, but also many attack type forest roads, and sometimes I hit trees with Normal Back Mirror. Therefore, the Trial Mirror was installed under the handlebar. The mounting hole for the OEMB Back Mirror was left open. Well, it is OK to ignore it, but it is not so nice, so I covered the hole.
Functionally, a cheap and lightweight Plastic hole plug is sufficient. However, the Type, which is stuffed into a screw hole, is difficult to put on and take off. (It is easy to put it on by just pushing it in, but a little troublesome to take it off.) For on-road touring, the OEM Mirror is easier to use, so we will return to the OEM type. In such cases, the screw type is more convenient.
The disadvantage is that it is an aluminum cut-out, so it is naturally costly and expensive. You will pay about 1pc.500 yen just to plug the hole. (Plastic hole plugs are lightweight and much cheaper.)
I would recommend it to those who are concerned about the screw holes that removed OEMMirror and who are concerned about looking good or who repeatedly install and remove the OEMMirror.
Inexpensive, lightweight Material if you just want to plug the holes:Plastic is good.
View detail
Mirror Cap
I bought it for some reason, but the texture was there and the price was Reasonable. View detail
I think black looks better
I have been looking for it for a long time and finally let me see it. There is no difficulty in the installation process. Just unscrew the original mirror screws and install it directly. I prefer the black appearance. It is low-key and chic and matches the car very well. Moreover, its material It will not rust, which makes me very satisfied, and I may never find a better product than it. -------------------------------------------------- -------- After looking for it for a long time, I finally saw it. There was no difficulty during the installation process. As long as the original mirror screw was unscrewed, I could install it directly. black appearance. It won't rust, which makes me very satisfied. I may no longer find a product that is better than it. Powered by Google Translator View detail
High! But cool!
It's just as the Title says, the Anodized colors are really beautiful and upscale!
But it's expensive lol Slotted screwdriver was used to install it. It's so cool, it's a Recommendation!
View detail
usually
The texture is normal and a bit expensive for a Mirror filler. View detail
I bought it again, but it was still too expensive...
I bought a new Mirror hall stash when I reinstalled the bar end mirror, but it was still too expensive.
I like the texture, though.
View detail
No discrepancy, no cheapness, good!
OEMMirror→I bought this to fill the hole because I changed to a bar end mirror. It is totally textured and looks beautiful. I think the price is a little less than Friendly. View detail
In Mirror hall not used by Demon150GR
The GPX Demon150GR has a rubber cap blocking the mirror hall of the M10 Standard Thread Screw, perhaps a remnant from another vehicle, and I'd like to remove it because I'm concerned about the deterioration of the rubber, but in any case I'd like to remove it so that I can use it as a press-up as well. This Mirror Hole Cover Cap is installed. Compared to the common types, the NASA TypeSeries of POSH products have a more rugged design, which I prefer, so I chose this one. I think it is better to install the cap without putting a wound as much as possible. View detail
A little small, but works fine.
Amazon. Normal Thread Screw, Opposite Thread Screw Of Quantity:I bought a set, but both were Normal Thread Screws, so I returned them and repurchased from webike.
I'm not sure if it's cosmetically sound since it's not a Large price.
If you use a bar end mirror, it is necessary to have a pure normal thread screw hole.
The aluminum seemed to deform when torque was applied, so I lightly tightened it with a ten-yen coin.
This product is sufficient because it only plugs the screw holes.
If I had to pick one, I'd say it was Exactly right if the diameter was a bit larger.
View detail
high
I bought it because I made a bar end mirror.
The handlebar is black, so choose black.
I think it's a very expensive product for the price.
Easy to lick when installing and removing with a slotted screwdriver
Don't put too much pressure on it, it will lick you in one shot.
SmallParts, but it's Exactly after Mirror.
Next time I won't buy it.
View detail
It's also made of steel rather than rubber mirror caps.
I bought this because I needed a mirror cap after attaching the bar end mirror. Since it is a general-purpose 10M type, there was no difficulty in attaching it. A slightly longer flat-blade screwdriver or coin just needed for attachment will suffice. View detail
I can't find a substitute.
Originally it would be something to fill in when you remove the Mirror, but I had a part of my kid's bike that I wanted to block off from the M10, so I bought it with the extra Point.
Because it cannot be said that it is indeed hand tightening, I thought to use Slotted screwdriver, but as far as the Screw head is concerned, Slotted screwdriver was expected to bite, so I took out 500 Yen coin from Wallet and fastened it with a comb.
It's almost a toy Material, but on the other hand, it's not sold in Screw stores, so I'm not sure if it's worth the price.
View detail
I'm not sure how to tighten it up
I bought it as a blindfold in Mirror hall
You can choose from a variety of colors, but I chose Silver to match the colors around it
The product itself isn't bad, but the way it was tightened up wasn't great for me personally
Hex wrenches are included, but they are not used as they should be, but rather to hook and tighten It will be a thing (Second photo.)
When you apply Torque, the hole will be a little bit wound and you will get BALI It is recommended to protect and tighten the tool tip with Masking tape
I like the look of it, so I'm happy with it for now
View detail
Casually, yet parenthesis-wise!
What made you decide to buy?
The KOSO:Mini3Digital air-fuel ratio meter is installed in the Bore up GROM, and it's a good idea to use it casually and securely Parenthesis to install well!
How was your experience with it?
Posh:Attached to Universal mirror holder M8 and Pitch 1.25 The actual application is the Mirror Hole Cover Cap The actual application is the Mirror Hole Cover Cap, but this time I used the Meter Bracket I don't know how long it can withstand vibration, etc Looks Parenthesis well done
Was the installation difficult?
It is installed by hooking the attached wrench for tightening Because the hook part of the Hole Cover Cap is shallow, no Browning is possible I thought it was the one to make the wrench for tightening penetrating before I purchased it But unlike Image, I couldn't tighten it firmly, because GROM has a lot of vibration I just hope it doesn't get loose and drop somewhere
【Please tell me the installation point and hang】
As mentioned earlier, the attached wrench for tightening is hooked and installed, but it is not Work carefully because working on Brown can damage the product you just purchased You should! I'm wondering if I should use a screw locker because the tightening torque is too lenient......in the future I would like to take measures while watching the state of
[Others]
The price is about 700. 1 Mirror Hole Cover Cap is included Because it is made in Japan, the quality and finish are good This time, I used the KOSO:Mini3Digital air-fuel ratio meter in a casual manner, and yet still have a lot of fun with it Parenthesis well purchased to install, but if you include the meter, it's quite It took a long time, but our parts are also pleased in the world of self-satisfaction Compared to the machine, Parts is also more affordable, so I can't stop being complacent
View detail