Reviews
Fits: SUZUKI GSX-S1000F, SUZUKI GSX-S1000, SUZUKI GSX-S1000F, SUZUKI GSX-S1000
Processing is assumed to be Large.
The Instruction Manual states that some modifications may be required, but basically, Dry Carbon, an Other Brand Product, can be installed without modifications in most cases. As usual, this product also requires modification. The remaining 20% will be modified during the installation process.:Pair (for Left and Right) The gap between the two is different, so if you are concerned about the gap, you should refrain from using this product. I had high expectations for this brand because it has been gaining momentum recently, but I have a problem with the outside of Dry Carbon products, including some AEC products. View detail
Fits: SUZUKI GSX-S1000F, SUZUKI GSX-S1000, SUZUKI GSX-S1000F, SUZUKI GSX-S1000
Installation with processing
Since this product is installed with modification, it cannot be mounted with a simple bolt. However, even with modification, the bolt holes are not perfectly aligned, so those who are concerned about clearance should not use the bolt holes. There are two places where the OEM speed nut is transplanted and fixed, but the holes obviously do not fit and the bolt does not pass through, so I would like you to inspect and make it right. (Lol) I know it's not what Large did, but it's a shame because it's a Brand I had high hopes for. View detail
Dress-up effect
This product covers the connection between the Frame and the Swing Arm, and can be installed in a quantity.:Pair (for Left and Right) It is easy because you only need to sandwich the Cover from the Bolt with the Bolt.
The 1000GT is not listed as an applicable model, but I got it because it has the same Frame as the S1000, so I assumed it would be able to be installed.
It was easy to install as intended. To be safe, Screw lock was applied during installation.
After installation, there is no difference between the color of the cowl and the large size, so a sense of unity has been achieved.
View detail
Fits: HONDA CBR1000RR, HONDA CBR1000RR, HONDA CB1000R, YAMAHA YZF-R1, YAMAHA MT-10, YAMAHA YZF-R6, YAMAHA MT-09, YAMAHA MT-09 TRACER, YAMAHA XSR900, YAMAHA TRACER900, YAMAHA MT-07, YAMAHA XSR700, YAMAHA YZF-R25, YAMAHA YZF-R3, YAMAHA MT-25, YAMAHA MT-03, SUZUKI GSX-R1000, SUZUKI V-STROM250, SUZUKI GSX-R600, SUZUKI GSX-R750
Master cylinder cap
Easy to install and good quality. Cheaper than other manufacturers. View detail
Certainly the holes don't match.
The holes do not align as shown in the previous Review.
It is made to be fastened in three places, but it can be done by cutting the holes on the exhaust system side with a sander and fastening it in two places in the front and rear. It seems to be strong enough, and the NORMAL cover looks lame. It is a good item for those who are considering to use Slip-on Silencer for vehicle inspection and are tired of this cover because it is too shabby.
If you don't mind cutting and shaving, I'd buy it.
View detail
Fits: HONDA CBR1000RR, HONDA CBR1000RR, HONDA CB1000R, YAMAHA YZF-R1, YAMAHA MT-10, YAMAHA YZF-R6, YAMAHA MT-09, YAMAHA MT-09 TRACER, YAMAHA XSR900, YAMAHA TRACER900, YAMAHA MT-07, YAMAHA XSR700, YAMAHA YZF-R25, YAMAHA YZF-R3, YAMAHA MT-25, YAMAHA MT-03, SUZUKI GSX-R1000, SUZUKI V-STROM250, SUZUKI GSX-R600, SUZUKI GSX-R750
Master cap
One point Green Light is good. View detail
Handlebar Brace
I installed it to attach the Smartphone Holder. Installation is easy. I think this is a better choice if you are going to attach a Smartphone Bracket, as the Gold amount is not that different. View detail
Fits: HONDA CBR400R, HONDA CB400F, HONDA CBR650F, HONDA CBR400R, HONDA CBR250R, HONDA CB250R, HONDA CB250F, HONDA CBR650R, HONDA CBR500R, HONDA CB500F, HONDA CB300R, HONDA CBR500R, HONDA CB500F, HONDA CB300R
Parts removal and appearance change
I didn't want to wear a long and big Balancer because my body is small, but I didn't want to wear a long and big Balancer to reduce vibration. I couldn't find it, so I bought it. View detail
Fits: HONDA CB1000R, HONDA CBR1000RR
not quite
This product is not suitable for people with short fingers. View detail
reasonably good
I bought it because it is Adjustable. It is indeed adjustable and good. However, I feel that the extending part is a little unreliable. It would be better if it were a little heavier. Well, I think it is fine for normal use. View detail
Fits: HONDA CB1000R, HONDA CBR1000RR
not quite
Spec. change from U-KANAYAShort.
I bought it because of the ability to adjust the length to my liking. However, the Clutch Side is the smallest width and the Quantity:Set but it is far away. Further long distance makes my fingers hurt at the gate of Lever. Is it a matter of getting used to it? ??
View detail
Subtle
The texture is cheap for the price. 4,000 yen is about right. View detail
Fits: HONDA CB250F, HONDA CBR250R, HONDA MSX125, HONDA GROM, HONDA Monkey125, HONDA NS-1, HONDA CBR400R, HONDA 400X, HONDA CB400F, HONDA CB250R
It is ◎ that it no longer hits the Small finger when gripping it.
Replaced with a Short Type one since I never grip with 4Finger.
It is ◎ that it no longer hits the Small finger when gripping it.
The replacement work itself was easy, but the Instruction Manual contains many descriptions of other car models, and it is difficult to understand, so I recommend watching Youtube or other media beforehand.
I'm also a little concerned about rattling compared to OEM.
View detail
Not perfectly fitment
I received in good condition and good quality product, but after I install to my 2011 yamaha yzf r6 , this product not very to my motorcycle, between fuel tank gap very big. View detail
Fits: HONDA MSX125 (GROM), DUCATI 1199Panigale, DUCATI 848, DUCATI 848EVO, DUCATI 899Panigale, DUCATI DIAVEL, DUCATI HYPERMOTARD796, DUCATI HYPERMOTARD821, DUCATI MONSTER 1200, DUCATI MONSTER 821, DUCATI MONSTER1100EVO, DUCATI MONSTER696, DUCATI MONSTER796, DUCATI MULTISTRADA 1200, HONDA 400X, HONDA CB1100, HONDA CB1300 SF, HONDA CB250F, HONDA CB400F (2013-), HONDA CB400SF
Is quality declining?
It can be opened and closed with a tool, which is easier than opening an OEM Knob with monstrous force.
Wiring can be done and Design is good.
I have used several of them and had no problems, but I guess it was around the time the company name was changed to SPEEDRA.
The hexagonal hole of the one I received was rattling in BALI, so I requested a replacement and was refused with Spec.
It wasn't like that before...
View detail
AppearanceParts
The head is small and unobtrusive.
It can be used as it is because it belongs to the "with Washer" genus.
View detail
Compromise with Titaniumium color
[How is it used?
To hide the hole after removal of the sub-frame
Was the one you received as per Image?
As shown in the picture. Good texture.
Was the installation difficult?
It is easy to use because all you have to do is plug it in.
How was your experience with it?
Fitting good. can be Accent.
[Included Parts:were they on?
None
[Was there anything that disappointed you?
Initially, I wanted to buy another Manufacturer's product in silver tailoring.
However, we were told that production was undecided, so we had to settle for a color here that was close to ours.
Cooperative. design and color disappoint.
Other items that would be helpful
Installation Point or hang Just plug it in/Instruction Manual Yes/Easy to understand ◯/Cautions None/Items to be purchased together None/Opinions and requests to Manufacturer Silver color, Polish and Plating lineup are desired.
View detail
It has a rather strong presence.
The plastic washer is also included, but it was a 13mm washer, which is commonly sold.
I think Bolt is good, but it is expensive.
View detail
Fits: YAMAHA YZF-R6, YAMAHA FZ8, YAMAHA YZF-R1, YAMAHA FJR1300
Small Scars
I was able to install it without any problems.
However, I was concerned about the feeling of roughness against my fingers when installing it.
Upon closer inspection, there was a smallish scratch that looked like it had been gouged out.
It's not that noticeable a scratch, so I'd say it's safe.
I thought it might be Out for some people.
It's not expensive, so I guess it can't be helped, but it's a shame.
View detail
Fits: KAWASAKI NINJA1000, KAWASAKI Z1000, KAWASAKI ZX-6R, KAWASAKI Z1000R, KAWASAKI Z900RS , KAWASAKI Z900RS CAFE
It may be better to use a retractable extension type or a Long Type.
I am very happy with the texture and appearance, which is much better than the OEM Lever.
However, in my personal opinion, I think Short Type is too short for Z900RS.
I use Lever as a basic Quantity.:It can be used without any problem since it is a 2pc hook, but those who hang 4pcs may feel that the Small finger is not so good.
View detail