Reviews
To bleed air from the Brake
Originally a Catch tank, it is used as a waste receptacle when bleed air is removed from the Brake.
I used to drill holes in the lids of plastic bottles, but it was inconvenient because the lids would break or slip off.
This product has a large hole that engages securely with the tube, so the tube does not move.
The One-Way Valve, which costs about 800 yen, makes air venting easy.
A dedicated air venting kit costs about 5,000 yen, but if you buy this product and Valve, it costs about 1,500 yen.
The capacity is sufficient for Motorcycle and it is not bulky.
View detail
Thin, square and cheap
I wanted to treat Blowby, which I had done with plastic bottles, and chose this one.
The reason why I chose it was decisively the price! Gold tanks are cool but expensive!
This Tank is thin and square, making it very easy to fix.
One ingenious point is that a rubber plate was inserted to fix the frame.
This is to prevent gapping and to prevent deterioration due to vibration. The included Strap is also long enough to fasten securely.
Blowby extended Hose and plunged into Filter #2.
When the Engine is instructed, that unpleasant Smell is reduced to Large! It has become an environmentally and rider-friendly Spec.
View detail
Very ordinary Catch tank
Catch tank is originally used for Circuit driving.
I'm using it as RadiatorReserver with some modifications.
It's not about performance.
Plating on the lid is easily damaged.
I'd like it to be Black or something anyway.
View detail
Blowby processing in Powerfull
I bought this as a replacement for a Catch tank that was used on a Z650 that I converted to a Power Filter, because it was damaged.
The previous Catch tank's rubber hose insertion part was torn off due to deterioration, so we selected this product, which has a gold hose insertion part from the engine (rubber is used to remove the hose from the tank) and is reasonably priced.
Since the Tank is square (previously round), it seems to be reasonably strong when secured with Tie Wrap.
So far we are satisfied with no damage.
View detail
I should have read the Race regulation carefully.
It is mandatory to install an oil catch tank when competing in a race.
I bought this one.Material:I bought it because it was cheap at Plastic.
In the current Regulation "Must have the Gold attribute." You are obliged to do so.
I regretted later that I should have read the MFJRegulationBook properly.
View detail
spare water bottle
The spare water bottle is a good quality replacement water bottle. Comes with a good heat resistant rubber hose. Suitable for racing and car use perfectly.(translated by Google Translator) View detail
Part Detail
<Size>
Bottle : Vertical 135 mm Horizontal 65 mm Depth 40 mm, Cap : Die-casting 40 mm Hose Insertion Length 20 mm Insertion diameter 12 mm, Drain : Material : Rubber 25 mm Hose Insertion Length 15 mm Insertion diameter 9 mm, Band mounting portion width 12 mm Depth 3 mm Center to center Pitch 65 mm
<Parts>
Bottle has rigidity, it does not feel dented in normal use. Drain rotates without being fixed. Cap is made by Die-casting and Smaller than Cap of Plastic bottle, the Bottle side is 22 mm, if there is a Bottle of the same diameter as this, it seems to be diversible.
<Overall rating>
I think that it is a reasonable price when considering the labor and parts cost for making this textured part with DIY. I regret that there is no Variation in the shape of Bottle.
View detail
Does the job!
Affordable, perfect capacity and comes with long straps and plenty of hose...A lot of other kits come with tiny straps that are basically useless, these however were plenty long and are easy to remove too. Would buy again/10 View detail
Between Breather
I used it when I attached the Breather kit to LEAD 110.
There is nothing special to mention. I can usually use it as an Oil catch tank, but I felt that the price is a bit expensive.
Large Kimono was slightly smelder than I imagined, but it was good as it is installed in a narrow Space.
Since capacity is visible, I made it as a product of plastics, but Aluminum may be better.
View detail
Adhesion of Nozzle part of 8Φ is bad!
I installed it on ADDRESS V 125!
Thanks to Blowby Sludge countermeasure by Oil mist attached to Throttle valve!
Address Blowby Reduction Hose is in the immediate vicinity of the Air cleaner 's Throttle valve, so I will wear it and emit Large Air.
I think that it is because of this early reduction of Oil. Also, since this Oil catch tank is translucent, it is obvious how much Oil is being released!
I drilled a hole in Cup and attached Nozzle so that it could be thrown away when Oil gathered. (It is convenient to use one type of bukubuku 6M Nozzle selling to Gold fish store something!
The one of Valve 12 Φ attached to the lid part is not so good, although it can be integrated, 8φ Nozzle was glued at the arrival!
Everyone may have written it in Impression but it can be truly taken.
I do not apply too much negative pressure, but I think that it is better to reattach the part here. Is there a disadvantage here?
Since the price is cheap, why not?
Unsatisfied with Nozzle, ★ 3 pieces!
View detail
[Webike Monitor] Although there is no high grade feeling like a Catch tank made from an Aluminum, I think that it is light and finds it useful very much not to carry heavy loads, such as four MINIs. I think that what a Band does not separate fr
[Webike Monitor]
Although there is no high grade feeling like a Catch tank made from an Aluminum, I think that it is light and finds it useful very much not to carry heavy loads, such as four MINIs.
I think that what a Band does not separate from easily is good since the band groove is attached to the Tank main part.
View detail
A hole opens two places to a lid and it is a Cable tie and with a Hose. Although it was troublesome to have made a hole in other containers and it purchased, it is the star 5 if cheap to a slight degree.
A hole opens two places to a lid and it is a Cable tie and with a Hose. Although it was troublesome to have made a hole in other containers and it purchased, it is the star 5 if cheap to a slight degree. View detail
Since it was required in a Circuit, it attached. It is functional, a price is compared with an One-off or exclusive elegance, and it is 1/10 or less! Completely with [ in the form which considered fixation by the Cable tie ] no problem now!
Since it was required in a Circuit, it attached.
It is functional, a price is compared with an One-off or exclusive elegance, and it is 1/10 or less! Completely with [ in the form which considered fixation by the
Cable tie ] no problem now!
View detail
It purchased in order to catch blowby gas. Well [ although told also about others, if a black lid applies power strongly, it will come off, and ]. He reinforced with the adhesive bond before use. It just said that sealing performance was so so
It purchased in order to catch blowby gas.
Well [ although told also about others, if a black lid applies power strongly, it will come off, and ].
He reinforced with the adhesive bond before use.
It just said that sealing performance was so so.
Although it cannot say, when perfection is called common within the limits, it is.
View detail