Reviews
Mellow SmokeSilver
Mellow Smoke is difficult to see due to the reflection on the inside, so the inside is darkened. [Color] Smoke might be better.
I thought I had been gently wiping water droplets off with Towel after normal maintenance and after using it in the rain a few times, but the plating is peeling off and it is hard to see these days.
Very Delicate Plating.
It did not last a year.
View detail
Not good
It might be a little hard to see and I don't like it. View detail
Fits: SUZUKI GSX750S, SUZUKI GSX750SS, SUZUKI GS1000
Does not take into account the intent of Low Friction
Before use, the Advantage arrived in a bag with about 3 layers tied around it and very tight curvature.
It is partly bent and habitual, and although the product claims to be Super low friction, it is ruined by Advantage's packaging.
It does not seem to fully reflect the intent of the producer.
I would like to see Advantage improve the shipping conditions with a more gradual curvature.
WeBig is in the process of requesting a replacement.
View detail
I failed.
When replacing the master cylinder, the stock switch box would give me more room for the gas pedal wire.
I bought it The wire is 800mm, and the inner pipe is 44mm without thinking.
This is the source of the mistake. There's no point in making it so high throttle in the first place.
I put it on and it's really high throttle, sweaty, and the gas pedal is really heavy. ・・・・
The wire also seemed a little long ・・・・
I think the balance with Rajpon is great, but maybe this time I made a mistake in choosing the right parts.
It's not an improvement, it's a deterioration.
I'd like to try it next time with a 35mm throttle and 700mm wire.
View detail
For Silencer protection
I have always enjoyed forest road touring with gasgas EC250 as a hobby.
It is an application that sometimes runs a little HARD.
This time I bought it with the earnest desire not to add any more scratches to Silencer.
Installation is done by pulling as hard as you can on the Rubber loop.
It requires quite a few parents.
It is cool as a Design, and it Guard Silencer well as a Protector.
I was a little disappointed that it slides and moves when the light is actually turned on, and at first I was concerned about it and had to change the position of the outlet of the exhaust system every time. Recently, I have come to think that it is fine as long as it is on, and I use it as it is without fixing it.
I think it is difficult to increase the number of scratches on the Exhaust System.
I want to remove it when I get good at it.
View detail
Even though it's only for car models ….
I purchased it specifically for my car model, but could not install it without modifications. View detail
Sleeves are too short.
The sleeves were 3cm too short and I returned them asap. I wonder what standard they are meeting.
I found another color at a special price, but the special price is non-returnable.
I chose this color and I'm glad I was able to return it.
I can't buy Wear's specials because I can't try them on.
View detail
Heart breaker!
First and foremost, we must note that the BALI in the cutting process is quite bad, and honestly, it is the Level that causes injury.
If it is a FOR JAPAN MODEL product, I think it is a hesitant Level to ship the product as it is.
And it is not very good as accuracy, and the Center axis is also blurred.
However, it does not mean that it cannot be used at all. If BALI is removed sesse-sese-sese and military gloves are used, it is not impossible to use it.
However, we do not anticipate that the product will be used many times, and we hope that you will consider it as a disposable level for this time.
Personally, I would urge everyone to choose a more solid product when considering it as a tool.
well ♪ Hyakkety-yak ♪ It is possible for people who understand the concept of "Level" to purchase the product.
View detail
Not Standard Size
25.2mm, so it will be sandwiched between the rubber plates.
However, Rubber sticks out, does not pinch properly, etc. Stress builds up subtly.
In the end, I managed to attach it, but I was not satisfied with the wobble, the subtle texture, and the fact that it was rather large for a skimmer Switch.
I think it would be better to use a 22mm size made by NAKA0 with waterproof and wiring processing...
Well, it's too much trouble to replace it, so I'll use it until it breaks.
View detail
Poor return of Engine Starter Motor
After a year and a half of use, the return of the Engine Starter Motor was poor and the CellMotor kept turning.
The same thing is written in the review of KIJIMA's Engine Stop Switch, so things seem to be the same.
For now, I did a Silicon spray and it came back, but I'm sure it will reappear after a while.
It is inexpensive, so let's just use it as such. (Laughter)
View detail
Durability may be difficult.
The ease of installation was a plus.
The battery stopped charging less than six months after installation.
According to Manufacturer, it was due to age and not covered by warranty.
I hoped it would be a little sturdier and last longer.
View detail
Hmmm...
This is a replacement from OHLINS Grip, but the Fitting is poor.
It can be installed, but it does not feel right.
Is it expensive for the accuracy?
View detail
poor response
The MASTER of the front brake was replaced with a type without a switch, so a hydraulic switch was used.
The Stop-lamp did not light up with a light pull, and finally lit up when I gripped it a little like a hard brake.
View detail
It was too difficult for me.
I had experience pasting automotive film in the past, so I bought it thinking it would work, but it turned out to be disastrous.
The shape is complex and cannot be aligned well with subtle curved surfaces at all.
Moreover, it is difficult to remove air bubbles because of the thickness of the ??Film, and it is stretched so much that air bubbles do not come out at all.
It is wiser to be honest and ask the PRO to do this.
Sorry, this is a bit of a whiney impresario. Yes, the product is solid and looks good.
View detail
SLASHSlider
Mounting holes were slightly misaligned. View detail
Fits: HONDA CB400SF, HONDA CB400SF VTEC, HONDA CB400SUPER BOLDOR, HONDA CB400SF VTEC Revo, HONDA CB400SUPER BOLDOR
I was planning to tour at high speed, so I was hoping for a Handlebar shake effect.
I purchased this product because it was said to be compatible with my car model and year, but the included screws were too short and could not be installed.
Furthermore, upon closer inspection, there were also scratches.
It is a pity that the price was so high.
View detail
Care must be taken when assembling.
It seems to be incompatible with the Inner panel during installation.
I would like to process and correct.
It's cheap, so I guess it can't be helped.
View detail
Wiring branch connections are easy and good.
The differences in Cable size and current capacity are easy to recognize depending on the color.
Note that the Cover is divided between the main line side and the branch line side.
*Because the blade directly bites into the sheath for connection, use in locations with a lot of vibration may result in disconnection or poor contact.
*Care should be taken not to reuse the area once used.
It is easier said than done, since the connection can be made with just one pliers....
View detail
Fits: HONDA CB1300SF, HONDA CB1300SF, HONDA CB1300SF, HONDA CB1300 SUPER BOLDOR, HONDA CB1300 SUPER BOLDOR
K-factory radiator core guard
Now if there is a difference in width size of the radiators I had to re-drill the holes on the side brackets by about 5mm each side then the cover slotted over nice and tight so expect there could be some adjustment needed View detail
Fits: MV AGUSTA F4 RR, MV AGUSTA F4 RC, MV AGUSTA F4 R, MV AGUSTA F4
Ah
Bolt is short, so I diverted OEM, but it's going round and round, and I don't know if that's right or wrong. View detail