Reviews
DIY is not easy, but it's a great product
This product does not impair the aesthetics of the bike and enhances the rigidity of the vehicle body. Mounting is difficult on your own, I recommend going to the maintenance shop. The shimmering of chrome makes the bike very stand out. If you wear this, your bike gets a different look than others. View detail
Fits: HONDA DAX125
None
It is a good product with good sound and Design. View detail
Outstanding Workmanship Accuracy
I was going to settle for a cheap wide stand from an unfamiliar Manufacturer.
We chose this one because we were notified of its release by Over, a safe and reliable company.
The ground contact surface is firmly level with the ground, and there is only a gap that may or may not contain a sheet of cardboard.
(The photo above shows the gap, but it can be narrowed down a little more after adjustment.)
It was expensive, but I liked the satisfactory workmanship.
I chose the Powder coat one to avoid flying gravel.
The color is close to the paint of the OEMSide Stand, which is nice without looking bad.
However, two points should be kept in mind when installing the system.
1. side stand must be installed with the side stand raised
This product has a slight rattling to absorb errors on the car body side.
As mentioned in the Instruction Manual, fine adjustment of the mounting position is required before tightening the Bolt.
In this case, the Side Stand needs to be adjusted with the Side Stand raised.
Assuming that one person installs the handlebar, he/she will work while squatting and holding the handlebar with one hand.
If you tilt out of balance, you will have two choices:you will be caught between the Motorcycle and the Exhaust System, or you will be knocked over to the Exhaust System side.
We recommend using a Maintenance Stand or working with two or more people, but
When working alone, put it in 1st gear and use Brake Lock as shown below to stabilize it.
DAYTONA:Front Brake Lock
https://www.webike.net/sd/21825075/
2. low specified Torque
I use M5 and M6 Bolt to fix it, but the tightening Torque is specified to be less than 10nm.
This value cannot be set for some types of torque wrench. (Especially if it is for suspension, it may be too severe.)
The Bolt is tensioned so that it is relatively difficult to loosen, but
It is recommended to adhere to the specified Torque + use Threadlocker in combination.
Since the base material is aluminum, experience has shown that it licks easily when tightened by intuition.
Since no other parts need to be removed during the installation process
It is a relatively easy component to install.
It is expensive and Bolt can be loose and dropped.
Be careful not to ruin it.
View detail
Work of art swingarm that works.
Had my eye on this swingarm from over racing for sometime now. Sure its an investment, but you get what you pay for and it did not disappoint. Function and fit 5 stars all the way. View detail
Vibration directly
only one choice
Great texture.
I just licked one spot when I put it on.
That's also where you change the Position.
Even an amateur can install it easily without referring to the Instruction Manual.
Sprocket cover and Quantity:It's cool to match the texture with the set.
View detail
Cost performance ◎
We chose the over-made model because we wanted to coordinate it with the sub-frames.
The installation was done by Shop.
Material:Polishing was selected, and the connection with the sub-frame is now shiningly gorgeous.
Custom feeling is up, I am satisfied.
View detail
Good quality at an affordable price.
It is a low-priced but high quality product and comes with Bolt and other accessories, making it a highly satisfactory product. View detail
Fits: KAWASAKI ZX-25R, KAWASAKI ZX-25R SE
My first Full Exhaust System
I replaced the OEM after 8000 km on it.
Low-speed Torque is thinner than OEM.
Idling sound is 97~99 and very Large sounding, even at low speeds.
It has been blowing up better since around 6000.
I would recommend it to anyone who wants to get a large sound, which can be done with JMCA.
Also, there were no JMCA certification documents included.
View detail
Sounds and looks great!
After replacing the block tie ya, Torque was installed to compensate for the thinner Torque.
I was torn between this and SP Tadao, but I chose this one because of its simple, never-ending design.
Installation is simple and easy for those who can remove the exterior.
Exhaust Gasket and Liquid Gasket (for the joint between exhaust pipe and silencer) must be prepared in advance.
A simple Instruction Manual is also included, but it does not describe the Torque for tightening the Flange nut.
We had no choice but to install it, making sure there were no rattles or exhaust leaks.
Shorter and a little more inward than NORMAL, giving it a resisted look.
Simple and good design that you will never get tired of.
Exhaust Heat Guard's "Over" The removal of the "+" is not so much as to be noticeable.
Exhaust System sound is crisp and dry.
It is comfortable while Idling and running, and I like it very much.
Compared to NORMAL, the volume is a little more Large.
Torque is there from the start to low and medium speeds, and it seems to be a little Plus to the thinner tire by the tire exchange.
It responds to the opening and closing of the Axel in a straightforward manner, making it easy to operate even at low speeds.
It also turns Smoothly to high RPM, but the Rev limit comes first.
In 4th gear, it sounded like it was stuck all the time, which was grating, so I changed the FSprocket to 15T to lower the rpm.
The Torque is slightly thinner at the start of the run, but not enough to be bothersome, and the top speed is slightly higher.
When I rode after the installation, there is White smoke and a Chemical smell that Biglizes at the traffic light.
By the time the car has traveled 50-100 km, it will no longer appear.
View detail
Things are best ?? with notes
I bought this product because of the look and the Position.
The texture and build quality is as good as OVER!
I bought it without thinking, but there were pitfalls.
View detail
Jack-up required
When you look down while straddling it, it has a cool Machine feel to it.
I am quite satisfied, but there is a caveat.
Although not mentioned in the Instruction Manual, the Engine must be supported by a Jack or the Bolt may not fit.
Specifically, when removing the OEM FrontEngineMounting Bolt and replacing it with the Engine Mount Collar Bolt, the Engine was lowered and the Bolt did not fit properly.
To prevent this, the Engine must be supported by Jack.
If it does not fit easily, fine-tune the position with Jack and never forcefully tighten Bolt.
You should really be careful because the worst that can happen is that the Engine side will be damaged and you will fly hundreds of thousands of dollars for repair and replacement.
Even if you ask Shop to install it, it is safer to ask a reliable place such as Plaza.
The Instruction Manual does not list the tightening Torque, so there is also a risk in that regard if you ask a contractor who does not refer to the Service Manual.
View detail
JAPAN is good after all!
Previously, Thailand View detail
Looks good.
The color and shape are great.
My calves no longer hit me when I put my feet down.
View detail
Refreshing if it is a new Emblem.
I thought it was from a different Silencer but I replaced it with one from a Silencer for RN20 YZF-R1.
Emblem size and Rivet mounting hole pitch are the same, so it can be used without modification.
After polishing with sisal and a white stick, I was tired of the worn emblem and replaced it with a new one.
View detail
It's easy lol and looks perfect!
It is easy to fit.
The visual effect is perfect!
Cost performance is honestly bad but it looks better so I'm ok with it lol.
View detail
It's expensive but you won't regret buying it! 100% satisfaction!
I had a hard time peeling the gasket off, but other than that, it went on very easily. I am very satisfied with this purchase. View detail
Fits: KAWASAKI ZX-25R, KAWASAKI ZX-25R SE
5 points for sound +6, ease of installation -1
I searched for Japan Government Certificated, Short, and Megaphone Type and found no options, so I bought it.
Installation
In addition to Rear Stand + In-vehicle Jack, Glasses, plate latche, and other naturally necessary items are used as appropriate.
I am not good at removing Gasket.
Instruction manual is normal, only the exhaust pipe is hard to fit in the middle, and there is no description of the procedure of Cowl removal and installation, or Torque tightening.
Silencer Bracket is to be attached to the LINK of the rear suspension, but it would be better to have an on-board Jack for the car.
And Silencer, even with 4 layers of Washer, it hits the DrumstickDrumstick on the Swing Arm! (Image is that) 。
I ended up with a 10mm collar and a single Washer to float 0.5mm. (No image) 。
The supplied M8 bolt is not long enough, so a handheld cap bolt is used.
About Sound
Idling…The bass sound is at a level that makes me wonder if it is Japan Government Certificated. In the middle of a residential area, it is likely to be reported.
I use only 4000~6000 rpm for city driving… I use only 4000~6000 rpm for fuel efficiency, but the bass is nice when I start driving.
Winding…I'm satisfied with the Race ish sound of the Engine from around 6000 RPM, so I don't pay that much attention to the Exhaust SystemSound.
It is not too expensive for a full exhaust system, and it is worth buying rather than being stuck with an unfamiliar foreign-made product. In fact, the Idling sound was bigger than expected, but I have no regrets.
View detail
It's still Over.
[How is it used?
Rear Sets were introduced because the Normal step hits the calf when the foot is lowered and makes it difficult to get a good footing.
Was the one you received as per Image?
As per Image, Over's products have a good texture.
Was the installation difficult?
Installed with reference to the Installation Manual and YouTube. The troublesome Brake Side was installed without any problems.
I felt the shift rod was a little short.
How was your experience with it?
No more calf hitting the ground when lowering the foot. The rigidity while driving has also increased.
However, it is not Foldable, so when I was taking my foot off the footpeg at low speeds, my toe caught and I suffered a LargeDamage to my calf. Be careful. ←Just my own fault....
View detail
be quick to react
Quality and texture information Cool with aluminum cutting be quick to react to the feeling of use to find fun in driving An impact No. 1903-N is required by holding the ANEX screw for installation. There is no instrument panel screw groove Cost performance and comparison with other products are said to be expensive, but it is worth it Delivery and packaging to WeBike in a week The packaging is great A caveat is that the seat position changes. You have to know that and buy it View detail
it's the best
Anyway, it is beautifully made.
I have not yet been able to run the machine on my own, but it is clear that the Rear movement is better than that of the Normal Swing Arm.
We replaced the standard KITACO rear shocks with KITACO×GEARS rear shocks, so we think this may also have an effect.
View detail