Reviews
Axle Slider removal and installation
I had a nail puncture my rear tire and i needed to remove the rear wheel to have it fix. Initially i thought it was difficult to remove the slider but it is just a direct bolt on to the rear axle. There is no pins or special locks on the slider, its just a regular bolt on both ends of the axle slider. I assume its the same process with the front axle slider. overall its an easy fix. View detail
Cheap, strong, rustproof
This is the same Parts that helped me when I was riding WR250.
By the way, I'm haGap from checking WeBig's compatibility, but CRF250L M RALLY50 MD44 will also fit, 44-47mm will fit, I will let you know.
I purchased this product in conjunction with the purchase of YOSHIMURAExhaust pipe.
As expected, the OEM exhaust clamp was rusty and rusty when removed.
Bolt broke.
I bought it on Amazon Prime, so I placed the order in the afternoon and it arrived first thing the next morning!
View detail
Fits: HONDA CB750 Four(CB750K)
cb750FourExhaust SystemConnecting Pipe
Tightening Band and Quantity:The Set is sold by other Shops, but the price is quite high and it is hard to find it because only the tubing is enough, but it is sold by your company and it was a big help! View detail
Fits: HONDA VFR800F, HONDA VFR800X, HONDA CBR600RR, HONDA CBR1000RR, HONDA CBR600RR, HONDA CBR1000RR, HONDA CBR1000RR
Satisfied with cost-effectiveness as For RacingPad
I installed it on Circuit Running's CBR600RR (PC40 2011).
Speaking of brembo's racing pads, Z04, Z03 for endurance, and Z10 recently released are the standard, but they are expensive...
I chose the far cheaper RacingCompound (RC) since it is not used for Solidly's Race.
Before the replacement, it was a replacement from HRC (Honda's RaceParts) N615.
This was not a complaint, but the Quantity:30,000 yen for 1 Set for 1 Vehicle...
The bremboZ03 is a Quantity:40,000 yen for 1 Set for 1 Vehicle....
I was a bit worried about the price of the racing pad, which is less than half of the price of the racing pad, but brembo claims it is "for Race", so I was a bit nervous and had mixed expectations.
bremboRC is a CarbonCeramic system, which means it is not sintered.
Some people think that it has to be Sintered, but in conclusion, there was no problem.
Since the pad brand was changed, the disc surface was peeled with steel wool (Bonnstar) at the time of replacement.
Of course, when we replaced the pad, we also cleaned the Piston and replaced the DOT 5.1 Fluid. We finished it perfectly.
Here are my personal impressions after using it at Sports LandSUGO.
Control is good from the beginning to the back.
The μ at low temperatures is not extremely low, and there is no need to be conscious of heating to raise the temperature.
Even when the temperature rises, there is little change to BrakeTouch, which is a good impression (although it is also a new pad).
Low thermal strain, good strength of back plate
The surface of the disc becomes black due to the effect of heat and the carbon film.
The braking force of △ Full Brake is milder (less potent) than HRC/N615, and it would be easier if it bites a little more.
The amount of Dust powder on the Wheel is small, so it is expected to be more Life than HRC N615.
So I feel a slight difference in efficacy compared to the high price FOR RacePad, but it is a much higher dimension than OEM, and from the Balance of price and Brand reliability, I am glad I bought it.
Since the BrakeCost per pc driven drops to about half the cost, I can add that floating budget to the Tire cost.
View detail
Fits: HONDA NC750X, HONDA NC750X LD, HONDA NC750S, HONDA CB400F, YAMAHA XJ6S, YAMAHA XJ6F, YAMAHA XJ6F, HONDA Africa Twin650, HONDA VTR250, HONDA VT250SPADA, HONDA VFR400 PRO ARM, HONDA VT250 INTEGRA, HONDA VRX400R100 ROADSTER, HONDA Rebel500, HONDA Rebel250ABS, HONDA Rebel250, HONDA Rebel250 S Edition, HONDA Rebel1100, HONDA Rebel1100, HONDA NSR250SP
I bought the DaytonaRedPad because it works.
The NormalPad has a sizzling sensation, while the RedPad has a gut feeling instead of a thumping sensation. View detail
Easier riding posture
Medium. The texture is good, and the riding position is easy,
Wouldn't it be better to have no Seal affixed to the product?
View detail
Handlebar Brace
The length is adjustable, so it can be used even if the position is changed or the Motorcycle is changed. View detail
Fits: KAWASAKI NinjaH2SX, KAWASAKI NinjaH2SX SE, KAWASAKI NinjaH2SX SE+
Not only the phone Mount.
I purchased these parts to reduce the vibration coming from the Handlebar as well as the phone mount. I used to feel numbness in my hand due to the vibration, especially when turning at high RPMs, but this seems to have been slightly reduced after installing these Parts.
Of course, it can also be used as a smartphone mount.
If only the screws securing the handlebar to the bridge can be removed, the rest is bolt-on, so it is not a very large work, but anyway, removing the original screws is large and strange,
View detail
Large satisfaction, I should have changed it earlier.
I have tried various levers from brembo OEM, but this one fits me the best, including one for Clutch SideRCS.
When I inquired about the compatibility with my favorite XR0.11.71, I was told that it was not made by brembo, so I could not get an answer. I checked the description of ASite and found that RMCMASTER is available! I immediately bought it because the delivery date was earlier than this one.
View detail
Easy to use
There were not many options available for the GSX-S1000GT, but I am satisfied with the product. It is easy to adjust.
The shape of the Lever is common, but I personally would have liked the cross section to be more rounded for easier gripping.
View detail
It's not bad.
The lever position adjustment is a mechanism where the screw comes out and hits the base, so it is not possible to adjust without a tool. I would like to have a dial type adjustment like the brake lever.
The shape of the Lever is common, but I personally would have liked the cross section to be more rounded for easier gripping.
View detail
Fits: SUZUKI GSX-S1000, YAMAHA YZF-R6, YAMAHA YZF-R1S, YAMAHA YZF-R1, KAWASAKI Ninja ZX-6R, BMW S1000RR, BMW S1000R, SUZUKI GSX-R600, SUZUKI GSX-R750, SUZUKI GSX-S1000F, YAMAHA YZF-R1M, SUZUKI GSX-R1000R, KAWASAKI Ninja ZX-25R, KAWASAKI Z650RS, SUZUKI GSX-S1000GT, KAWASAKI Ninja ZX-4R SE, KAWASAKI Ninja ZX-4R RR, SUZUKI GSX-R1000, SUZUKI KATANA
appearance
It is almost all about looks. Installation is easy, but be sure to follow the tightening Torque. View detail
Fits: HONDA Dio (2 Cycles), HONDA Livudio SR, HONDA Dio (2 Cycles), HONDA Dio (2 Cycles), HONDA Superdio, HONDA Superdio, HONDA Livudio SR, HONDA Livdio ZX, HONDA Livdio ZX, HONDA Livdio ZX, HONDA livudio, HONDA Livdio ZX, HONDA livudio, HONDA DIO [Dio]., HONDA DIO [Dio].
Bearing was subtle.
I have concerns about Bearing.
It is made differently from OEM and the Ball easily comes off RoseRose and falls off.
It is easy to restore a dropped Ball, but I felt it would cause problems after assembly, so Bearing reused the original OEM.
Other than Bearing, I don't think it is much different from OEM.
View detail
Good position, good footing
Position is good, and fine tuning can be done with 4 positions.
The footing is also nice, as the footpeg is no longer in the way.
If I had my way, I would have liked to see Bolt in Black type.
View detail
Fits: SUZUKI GSX-S1000, SUZUKI GSX-S150, SUZUKI GSX-R150, SUZUKI GIXXER SF250, SUZUKI GIXXER SF250, SUZUKI KATANA, SUZUKI GSX-R1000, SUZUKI GSR750, SUZUKI V-Strom1000 XT ABS, SUZUKI V-Strom1000 ABS, SUZUKI SV650, SUZUKI V-Strom250, SUZUKI SV650X ABS, SUZUKI SV650 ABS, SUZUKI SV650X, KAWASAKI ZX-10R, DUCATI 999, DUCATI 999S, SUZUKI GSX-8S, SUZUKI GSX-S1000GT
good appearance and performance
It looks good, and anyone who installs it
The resin part is designed to turn so that it is easy to STAND.
View detail
Fits: SUZUKI , TRIUMPH DAYTONA675, KAWASAKI NINJA400, KAWASAKI NINJA1000 (Z1000SX), KAWASAKI ZX6R, KAWASAKI ninja, KAWASAKI ZX10R, KAWASAKI Z400, KAWASAKI Z800, KAWASAKI Z250, KAWASAKI Z1000, HONDA , KAWASAKI Ninja 1000SX, DUCATI Late 999, BMW S1000RR, DUCATI 749, BMW S1000R
Replaced from Chinese
I bought it after seeing other people using it at Motegi. Unlike the Chinese Hook, the J-TRIP Hook has a step to prevent the swing arm from hitting the swing arm. What I didn't understand was that the Hook has a double structure with a collar inside, but since the Hook doesn't rotate, I am wondering what the collar is for. I also think the price is a bit high. Well, I am satisfied with it. View detail
Installation is a challenge, but it looks good!
I found this product because my OEM side scoop had rust floating on the steel and matte black paint, even though I wash it frequently.
VMAX1700 itself is not very easy to maintain, so replacing the Parts around the Frame inevitably involves removing the Seat and DummyTank Cover, which is a kind of ritual that must be gone through.
I had searched the Net for blogs of people who had installed the same products in advance, so I went to a nearby YSP to find double-sided tape and CS wheel stops that I would not be able to reuse when I removed the product.:Pair (for Left and Right) Quantity for Duct cover of:2 Sets of OEM Parts are ordered and purchased.
Work Start on the day when everything is in place!
Seat, which is a ritual, Tank Cover removed and Side cover is Quantity.:Pair (for Left and Right) When removing the third bolt, be careful not to drop the bolt and damage it!
I tried to remove the U-shaped pin with a slotted screwdriver, and then I tried to remove the CS ring stopper with a slotted screwdriver, but it did not come off very well, so I used a backdoor technique and folded the reverse side of the mesh over at the projections through the three rectangular holes. I fixed it straight with Driver and RadioBench and pushed it from the reverse side with Driverretc. and only the net part came off from the front side.
All that remains is to position the product from the front side, peel off the double-sided tape portion, and affix it.
I found this to be by far the most efficient way to reduce the time and hassle of removal, so although it is different from the Manual, I had no particular problem with it.
I think the appearance is to your liking. While the overall silver color differentiates it from NORMAL, the two-tone color with black also tightens up the look, so it is hard to say that OEM parts are not good.
However, the material is Stainless Steel, which is by far the most rust-resistant. I don't think the English letter engraving is necessary.
It is a cosy way to change the look and feel of the product at this price.
View detail
Fits: KAWASAKI Ninja250, KAWASAKI Ninja400, KAWASAKI Z250, KAWASAKI Z400, KAWASAKI Eliminator400
It is still first class!
It is still first class!
Cool!
Installation is a simple push-on with the included clip bolt. (*´?`*)
This time I installed it on my wife's ELIMINATOR 400, but now I think I'll change my Z9 to it too.
View detail
Fits: KAWASAKI GPZ900R
extremely sturdy
OEM Resin Bracket, only has a squishy feel.
Since the Tail lens unit is suspended and secured to the Seat rail from the underside, it can be forgiven for being a bit squishy.
This was already starting to ripple even before it was a few years old. It's like an apologetic Cover.
The aluminum plate is now anodized black, making it sturdier and sharper.
Now we are at ease.
View detail
Fits: Others , HONDA 400X, HONDA ADV150, HONDA CB1000, HONDA CB1000, HONDA CB1000SF, HONDA CB1100, HONDA CB1100, HONDA CB1100CA, HONDA CB1100NA, HONDA CB1100SF, HONDA CB1100SF, HONDA CB1300SUPERFOUR, HONDA CB250F, HONDA CB250R, HONDA CB250R, HONDA CB300F, HONDA CB300F, HONDA CB300F, HONDA CB300R
License Plate Base
Installed on a '24 GSX1300R HAYABUSA 。 It was Exactly without interfering with YOSHIMURA's Fender lessKit. View detail