Reviews
Fits: HONDA GYRO system (TA01), HONDA GYRO system (TA02), HONDA GYRO series (TD01), HONDA jorio, HONDA Giorno, HONDA GIORNO CREA, HONDA ZOOMER, HONDA TACT, HONDA TACT, HONDA TACT, HONDA DIO General, HONDA TODAY, HONDA Byte, HONDA LEAD 50, HONDA LEAD 50, SYM DD 50
Aging
Used on a 1985 HondaTACTA-AF09.
It is quite old, but the mileage is short, so I thought it would be good, but I was also worried about deterioration since I was going to replace it with Belt replacement etc., so I replaced it together.
A 7mm socket is required for the exchange, but the outer diameter of the socket will need to be a little smaller, so it is necessary to prepare one.
I managed to remove and replace it, but the old Scooter RollerGrease had quite a bit of grease in it, but it was sealed, so it seemed to prevent the grease from flying around.
I think I will be able to drive for a long time again.
View detail
Fits: HONDA Lead 50, HONDA ZOOMER(Ruckus), HONDA TODAY, HONDA CREA SCOOPY, HONDA JULIO, HONDA Giorno, HONDA Giorno, HONDA GIORNO CREA, HONDA SUPER DIO, HONDA SUPER DIO, HONDA SMART DIO, HONDA TACT, HONDA TACT, HONDA TACT, HONDA DIO(4Cycle), HONDA DIO FIT, HONDA TOPIC, HONDA Byte, HONDA LIVE DIO, HONDA LIVE DIO
It was Garbage,,, it's Aluminum, so it will be crushed.
I didn't expect the material to be Aluminum...it doesn't say anywhere, so I didn't know what it was and I bought it.
Since it is Aluminum, it is just tightened with the stipulated Torque, but it crushes easily and makes no sense.
I'm crushed when I run after installation and I don't see any difference in acceleration.
I use a lot of KN projects because they are inexpensive and available, but this was Garbage.
View detail
Fits: HONDA CB125, HONDA CBX125, HONDA DJ-1, HONDA gyro canopy, HONDA TLR200, HONDA Super Cub 50, HONDA Lead 50, HONDA Lead 90, PGO MyBuBu125, SUZUKI K90, SUZUKI street magic, SUZUKI birdie, SYM fighter150, YAMAHA Cygnus, YAMAHA Cygnus, YAMAHA jog, YAMAHA jog sports, HONDA CBR125, KYMCO SOONER100, HONDA WAVE125
OEM Equivalent Product, cheaper than OEM
Used for LITTLE CUB.
The low beam ran out, and a short time later the high beam also ran out. I bought this one because it was an emergency situation and it was immediately available in stock. The standard is 25-1. The Pine Stripe part number is 1P2015.
The grade of the bulbs is also the same as the OEM, White Hot bulbs, not Halogen.
I also found HalogenType, but the price difference was about three times as much, so I decided to go with the cheaper version.
Replacement is Light rim bottom, Quantity:Pair (for Left and Right) Remove the screw on the Plus of the light rim and lift the light rim upward to remove it.
The Glass part is replaced while touching as little as possible. Time required:2 minutes.
It lit up with no problem. I am relieved. I don't know about the durability yet, but it is a long-established domestic product and I am sure there will be no problem.
View detail
Fits: HONDA CB125, HONDA CBX125, HONDA DJ-1, HONDA gyro canopy, HONDA TLR200, HONDA Super Cub 50, HONDA Lead 50, HONDA Lead 90, PGO MyBuBu125, SUZUKI K90, SUZUKI street magic, SUZUKI birdie, SYM fighter150, YAMAHA Cygnus, YAMAHA Cygnus, YAMAHA jog, YAMAHA jog sports, HONDA CBR125, KYMCO SOONER100, HONDA WAVE125
Product # 1P2004
One of my friends has a rare YAMAHA Town Mate 6 volt motorcycle. He was faced with the problem of finding incandescent headlamps. We are very lucky that this product is available in the webike. The workmanship is good. Great price. View detail
Fits: HONDA DJ-1L, HONDA CABINA 50, HONDA GYRO CANOPY, HONDA GYRO CANOPY, HONDA BROAD50, HONDA DIO, HONDA DIOSR, HONDA G DASH, HONDA DJ-1, HONDA DJ-1R, HONDA DJ-1RR, HONDA LEAD50, HONDA JOKER50, HONDA Giorno, HONDA TACT, SYM DD50, HONDA Live Dio Cesta, HONDA LIVE DIOZX, HONDA LIVE DIO ST, HONDA LIVE DIOSR
Clutch connection is also Smooth and usable without any problems.
After purchasing a GYRO CANOPY (TA03) with a mileage of 70,000 km, I checked the condition of the drivetrain and found that the clutch was in good condition.
The wear limit was exceeded, so we decided to use the for RepairClutch outer, OEM Center spring, also by KN Kikaku, and the
We replaced them at the same time.
The quality is comparable to OEM products and the price is reasonable.
Now we are hoping for durability.
View detail
Fits: HONDA TODAY, HONDA Super Tact, HONDA JOKER50, HONDA CABINA 50, HONDA GYROUP, HONDA GYROX, HONDA GYRO CANOPYTA02, HONDA GYRO CANOPYTA03, HONDA Giorno, HONDA SUPER DIO, HONDA SUPER DIOSR, HONDA SUPER DIOZX, HONDA TACT, HONDA DIO, HONDA DIO, HONDA BROAD50, HONDA LIVE DIO, HONDA LIVE DIOSR, HONDA LIVE DIOZX, HONDA LEAD50
It's cheap
After purchasing GYRO CANOPY with a mileage of 70,000 km, I checked the condition of the drivetrain, and found that the clutch was in good condition.
The wear limit was exceeded, so we decided to use Clutch for Repair, OEMCenter spring, also by KN Kikaku, and
We replaced them at the same time.
The quality is comparable to OEM products and the price is reasonable.
Now we are hoping for durability.
View detail
Fits: HONDA baton, HONDA baton, HONDA baton, HONDA baton, HONDA Superdio, HONDA Superdio, HONDA Superdio, HONDA Superdio, HONDA Superdio, HONDA Superdio, HONDA joker, HONDA Johno., HONDA Julio., HONDA Dio XR Baja, HONDA cabina, HONDA Cabina 90, HONDA Joker90, HONDA Dio AF18, HONDA Super Cub 90, HONDA broadcloth
Used in LEAD 90
I used it on a LEAD 90 with OEM and external chamber and it worked fine with no exhaust leaks. View detail
Fits: HONDA CB125, HONDA CBX125, HONDA TLR200, PGO MyBuBu125, SUZUKI K90, SUZUKI street magic, SUZUKI birdie, SYM fighter150, YAMAHA Cygnus, YAMAHA Cygnus, YAMAHA jog, YAMAHA jog sports, HONDA CBR125, KYMCO SOONER100, HONDA WAVE125, HONDA NSR50, HONDA NSR80, HONDA Super Cub 50, HONDA Super Cub 90, HONDA monkey
Normal is best
It is a standard product that is neither too much nor too little, and can be used with confidence. I haven't tried it yet, but when I replace the Valve, I almost always use this Valve. View detail
Fits: HONDA TODAY, HONDA DUNK, HONDA DIO SR, HONDA DIO SP, HONDA DIO, HONDA CABINA 90, HONDA All vehicles with the name DIO, HONDA JOKER90, HONDA BROAD 90, HONDA LEAD 90, HONDA G DASH, SYM DD50, KYMCO SUPER9, PGO PMX110, HONDA GYROUP, HONDA GYROX, HONDA GYRO CANOPY, HONDA DJ-1, HONDA DJ1R, HONDA DJ1RR
Weight Roller
Installed on KZ Planning's High speedPulley.
It works fine
View detail
Fits: APRILIA AREA51, APRILIA H2O, APRILIA HABANA50/CUSTOM50, APRILIA MOJITO50/C, APRILIA RALLY(LIQUIDCOOL), APRILIA SONIC50, APRILIA SR50(CARB), BENELLI 491RR/REPLICA, BENELLI 491ST, BENELLI NAKED, CAGIVA CUCCIOLO, DERBI Aventura, DERBI Fenix・FDSSuper・StartDS, DERBI Furax, DERBI Hunter(Spain), DERBI RD-2 Country, DERBI Urban, DERBI Vamos, DERBI VariantBox/SportR/Top, HONDA DIO50/SR
Denso Iridium power plug IWF24
The clamping has become more powerful after replacing it with this Iridium power plug.
The car now blows up smoothly with no lean feeling during acceleration and hill climbing. I would like to use this plug again when replacing the plug.
View detail
Fits: HONDA DJ-1, HONDA DJ-1, HONDA Gyro UP, HONDA gyro X, HONDA gyro canopy, HONDA Julio., HONDA Johno., HONDA Superdio, HONDA Superdio, HONDA Superdio, HONDA Superdio, HONDA baton, HONDA baton, HONDA diocesan, HONDA TODAY., HONDA TODAY., HONDA Livdio ZX, HONDA livudio, HONDA baton, HONDA baton
Functions but no hole to Wrench.
The title is true
When integrating the Clutch into the Driven, it cannot be secured because there are no holes.
If you have various tools, you can handle it, but if you don't have them, you may lack Torque tightening if you tighten it properly.
Dio that was only 35 kilos. (Mileage just under 30,000) is now close to 60, so I think its performance as Clutch is not bad.
View detail
Fits: HONDA GYRO system (TA01), HONDA GYRO system (TA02), HONDA GYRO series (TD01), HONDA jorio, HONDA Giorno, HONDA GIORNO CREA, HONDA ZOOMER, HONDA TACT, HONDA TACT, HONDA TACT, HONDA DIO General, HONDA TODAY, HONDA Byte, HONDA LEAD 50, HONDA LEAD 50, SYM DD 50
KN Planning Weight Roller6g
The Axel Response was better, but the RPMs were higher, making it harder to drive around apartment complexes in the early morning.
I would also change to a slightly heavier Roller.
View detail
Fits: HONDA GYRO system (TA01), HONDA GYRO system (TA02), HONDA GYRO series (TD01), HONDA jorio, HONDA Giorno, HONDA GIORNO CREA, HONDA ZOOMER, HONDA TACT, HONDA TACT, HONDA TACT, HONDA DIO General, HONDA TODAY, HONDA Byte, HONDA LEAD 50, HONDA LEAD 50, SYM DD 50
KN Planning Weight Roller6g
I have only installed it for a short time, but I felt that the start was not as good as the NORMAL.
Response is better compared to NORMAL while driving.
I gave it 3 stars because I don't know how durable the rest will be.
View detail
Fits: HONDA Zoomer/Ruckus DX, HONDA Zoomer/Ruckus, YAMAHA JOG, YAMAHA Vino, YAMAHA JOG, YAMAHA Vino, HONDA CHF50S Crea Scoopy SP, HONDA CHF50S Crea Scoopy SP, HONDA CHX50 Giorno Crea DX, HONDA CHX50 Giorno Crea, HONDA CHX50 Giorno Crea DX, HONDA Pax Club, HONDA QR50, HONDA Ruckus, HONDA Ruckus, HONDA SZ50 Tact Basic, HONDA SZ50 Tact S, HONDA XR100R, HONDA XR100R, HONDA XR70R
The squeak is Large.
Compared to OEM, Brake works better, but the squeal is Large.
DAYTONA products squeal in the same way, but Vesla's squeal is LARGER.
It would be a good product if it didn't squeak....
View detail
Fits: HONDA CB125, HONDA CBX125, HONDA DJ-1, HONDA gyro canopy, HONDA TLR200, HONDA Super Cub 50, HONDA Lead 50, HONDA Lead 90, PGO MyBuBu125, SUZUKI K90, SUZUKI street magic, SUZUKI birdie, SYM fighter150, YAMAHA Cygnus, YAMAHA Cygnus, YAMAHA jog, YAMAHA jog sports, HONDA CBR125, KYMCO SOONER100, HONDA WAVE125
Used for NSR50
Headlight went out and was replaced.
I don't know how bright it is because I basically don't ride at night.
Replacement was easy.
View detail
Fits: HONDA baton, HONDA baton, HONDA baton, HONDA baton, HONDA Superdio, HONDA Superdio, HONDA Superdio, HONDA Superdio, HONDA Superdio, HONDA Superdio, HONDA joker, HONDA Johno., HONDA Julio., HONDA Dio XR Baja, HONDA cabina, HONDA Cabina 90, HONDA Joker90, HONDA Dio AF18, HONDA Super Cub 90, HONDA broadcloth
Chamber replacement
I used it with LEAD 90.
It worked fine with no exhaust leaks.
I don't need three but bought them because they were cheap.
View detail
Fits: HONDA Zoomer/Ruckus DX, HONDA Zoomer/Ruckus, YAMAHA JOG, YAMAHA Vino, YAMAHA JOG, YAMAHA Vino, HONDA CHF50S Crea Scoopy SP, HONDA CHF50S Crea Scoopy SP, HONDA CHX50 Giorno Crea DX, HONDA CHX50 Giorno Crea, HONDA CHX50 Giorno Crea DX, HONDA Pax Club, HONDA QR50, HONDA Ruckus, HONDA Ruckus, HONDA SZ50 Tact Basic, HONDA SZ50 Tact S, HONDA XR100R, HONDA XR100R, HONDA XR70R
It's also used and trusted by Pw50.
I used it on my youngest son's QR50. Because it finally became MotorcycleDebut, I was given it at the Motorcycle shop in the neighborhood, so I quickly exchanged various things in Maintenance. I've used this Besra Brake Shoe on my eldest son's pw50, so there's no problem with the quality. View detail
Fits: HONDA CB125, HONDA CBX125, HONDA DJ-1, HONDA gyro canopy, HONDA TLR200, HONDA Lead 50, HONDA Lead 90, PGO MyBuBu125, SUZUKI K90, SUZUKI street magic, SUZUKI birdie, SYM fighter150, YAMAHA Cygnus, YAMAHA Cygnus, YAMAHA jog, YAMAHA jog sports, HONDA CBR125, KYMCO SOONER100, HONDA WAVE125, HONDA NS50F
Great light! But it's expensive.
CUB's OEM Headlight was crazy dark and my eyesight was deteriorating and I was worried about driving at night, so I installed this one.
The headlight lens was also changed to Multi-reflector, so I was worried about the optical axis, but there was no problem.
I really wanted to use White color, but Valve seems to be blue, so I thought that the whole Headlight is too young to be blue. [Color] I chose Clear and it was the right choice. I thought about using LED but I didn't want it to flicker;
I am satisfied with the product, but the price is too high for the consumables.
View detail
Fits: HONDA CB125, HONDA CBX125, HONDA DJ-1, HONDA gyro canopy, HONDA TLR200, HONDA Super Cub 50, HONDA Lead 50, HONDA Lead 90, PGO MyBuBu125, SUZUKI K90, SUZUKI street magic, SUZUKI birdie, SYM fighter150, YAMAHA Cygnus, YAMAHA Cygnus, YAMAHA jog, YAMAHA jog sports, HONDA CBR125, KYMCO SOONER100, HONDA WAVE125
I'm doing my job reasonably well.
Products used in TLRs modified from 6V to 12VSpec.
I don't see any changes compared to the OEMs, or rather, I don't know, since they don't run nearly as much at night.
There is no hindrance in its use. The fact that it does not have any problems means it is a good product.
View detail
Fits: HONDA CB125, HONDA CBX125, HONDA DJ-1, HONDA gyro canopy, HONDA TLR200, HONDA Super Cub 50, HONDA Lead 50, HONDA Lead 90, PGO MyBuBu125, SUZUKI K90, SUZUKI street magic, SUZUKI birdie, SYM fighter150, YAMAHA Cygnus, YAMAHA Cygnus, YAMAHA jog, YAMAHA jog sports, HONDA CBR125, KYMCO SOONER100, HONDA WAVE125
I'm doing my job reasonably well.
Products used in TLRs modified from 6V to 12VSpec.
I don't see any changes compared to the OEMs, or rather, I don't know, since they don't run nearly as much at night.
There is no hindrance in its use. The fact that it does not have any problems means it is a good product.
View detail