Reviews
Fits: KAWASAKI NINJA H2, KAWASAKI NINJA H2, KAWASAKI NINJA H2, KAWASAKI NINJA H2, KAWASAKI NINJA H2, KAWASAKI NINJA H2, KAWASAKI NINJA H2 CARBON, KAWASAKI NINJA H2 CARBON, KAWASAKI NINJA H2 CARBON, KAWASAKI NINJA H2R, KAWASAKI NINJA H2R, KAWASAKI NINJA H2R, KAWASAKI NINJA H2R, KAWASAKI NINJA H2R, KAWASAKI NINJA ZX-10R, KAWASAKI NINJA ZX-10R, KAWASAKI NINJA ZX-10R, KAWASAKI NINJA ZX-10R, KAWASAKI NINJA ZX-10R, KAWASAKI NINJA ZX-10R
Good but too expensive
Brake masterTank on the Front. [Color] I made it Smoke and so did Rear. [Color] I bought it to make Smoke.
The original bracket to prevent the cap from falling off has a gap between the top claw and the gap, so I bent the claw part down with pliers and attached it for the time being. It is ugly, so I'm going to keep it until I buy a dedicated one.
The appearance is less noticeable. [Color] I am satisfied with Smoke because there is no worry about yellowing, but I think it is too expensive.
View detail
Fits: KAWASAKI NINJA ZX-25R SE, KAWASAKI NINJA ZX-25R SE, KAWASAKI NINJA ZX-25R, KAWASAKI NINJA ZX-25R
Cheap and Easy SL Upgrade
Used to improve 250SL's BrakeTouch because it is cheap.
The OEM is 12.7 across, so I think 14mm is about right for Radial, but Nisshin starts at 17mm, and RCS has 15mm, but I don't feel like going that far with SL, and the unique handling of the Accelerator Wire makes it difficult to install.
We used the MASTER that was left over from the conversion of 25R to Radial, and expected that it would easily fit in the Cylinder because the Cylinder diameter and Banjo angle are the same.
The 25R is about 20,000 compared to the SLOEM of about 10,000 and has a better quality feel.
The result was quite easy to install.
Handlebar diameter, MASTER diameter, lever ratio, switch terminals, and banjo direction are all the same, so it is almost a simple installation.
For Clearance, it is OK to adjust the position to the extent that it touches LimitCowl or not, depending on the mounting angle.
The lever comes with SL one, but the height of the mating part is 6.8mm short, so I am considering whether to adjust it with a collar or to purchase one for 25R. (I lost the original Lever, so if it's attached, no problem) 。
There is no bleeder on the cylinder part, so the air bleed is not large enough, but if you pull it out from the Caliper side with a syringe, it is large enough to be durable.
The feel is a good Touch with a reasonably good response in the back, as opposed to the SL, which was initially scuffed but chica-chic in the back, but I have the impression that the amount of invalid Stroke is not so different.
This is recommended for those who want to improve SL Brake inexpensively since it can be pimped out if a Lever is included.
View detail
Fits: KAWASAKI NINJA ZX-10RR, KAWASAKI NINJA ZX-10RR, KAWASAKI NINJA ZX-10R ABS, KAWASAKI NINJA ZX-10R SE, KAWASAKI NINJA ZX-10RR, KAWASAKI NINJA H2, KAWASAKI NINJA H2, KAWASAKI NINJA H2, KAWASAKI NINJA H2, KAWASAKI NINJA H2, KAWASAKI NINJA H2 CARBON, KAWASAKI NINJA H2 CARBON, KAWASAKI NINJA H2, KAWASAKI NINJA H2 CARBON, KAWASAKI NINJA ZX-10R, KAWASAKI NINJA ZX-10R, KAWASAKI NINJA H2R, KAWASAKI NINJA H2R, KAWASAKI NINJA H2R, KAWASAKI NINJA H2R
Ninja100 Reserve changed so change
Reserve for Rear. [Color] Changed to Smoke.PartsNO43078-0575
This will reduce the capacity of the Bracket, so if you keep it as it is, the Bracket will be skewed.
So Quantity:Set to replace it
It's a good feeling.
View detail