Reviews
A must for low Torque measurements
I purchased this product to replace the stud bolt on my NSR250R Cylinder.
Low-Torque areas will be the source of Cracks if they become Overtorque even a little bit.
Torque management is essential.
So we used this one, and we are glad that we were able to use it successfully.
View detail
Torque wrench at last!
[How is it used?
I have been tightening the brake disc, caliper, and other important parts by hand for a long time, but I finally purchased a new one.
Was the one you received as per Image?
Yes
How was your experience with it?
You will want to Torque wrench everywhere.
[Points to note]
When storing, store at a lower level than the low value estimate.
Spring, etc., so that Torque settings do not go haywire.
How did it compare to other products?
Compared to KTC and others, the same.
It costs a few thousand dollars and is rarely active, but it is fun to work with. It's safe and you can learn the Torque sensation.
View detail
Good price and ease of use there.
[How is it used?
I was originally using a Torque wrench made by SIGNET with a different measuring range, but I wanted to manage the smallest bolt of the Torque better, so I bought this Torque wrench.
Was the one you received as per Image?
The picture showed the same as the SIGNET Torque wrench I usually use, but when I saw the product I received, it was much smaller than I imagined;
How was your experience with it?
Since it is the same as the Torque wrench made by SIGNET that we had been using, the Torque settings and other ease-of-use did not change.
However, it is a little troublesome that the Socket cannot be replaced as it is, since it is usually 3/8 size. (Lol)
Prices are relatively low, but accuracy (%) The cosmetics are also moderately cost-effective because they are comparable to other companies' products at ±3.
[Points to note]
If you normally use 3/8Size, you will need a Conversion Adapter or 1/4 Socket because the Socket size is different.
How did it compare to other products?
None
View detail
To manage the Torque
Not used for Meta, but can be used for Opposite Thread Screw View detail
To manage the Torque
Rarely used, but can be used for Opposite Thread Screw
Minus point that the scale is difficult to read.
View detail
To manage the Torque
Rarely used, but can be used for Opposite Thread Screws View detail
Torque wrench
I have the Torque wrench of kgf-m, but I didn't have the Torque wrench of N-m, so I bought it. View detail
Easy to use
[How is it used?
I bought this for my graduation from Hand Wrench.
I had a torque wrench to tighten the wheel nut etc., but I didn't have one for SmallTorque, so I chose this product which has a moderate setting range and is inexpensive.
Was the one you received as per Image?
I didn't expect much since it was inexpensive, but the texture is better than I expected and it comes in a plastic Hard case.
How was your experience with it?
Loosen the screw at the bottom and set Torque to Quantity.:Set and retighten to set the Torque without tools.
I felt that the Click feeling when it became the Torque which I set was sufficient. In a certain site, there was also a person who said that the Click feeling was too small, so there may be individual differences.
I think it's easy to use because you don't need to change batteries with Mechanical, and you can use it quickly and easily at any time.
In addition, I was a little disappointed that there was no Release of Socket. It might be unavoidable considering the price.
[Points to note]
There is nothing special about it. I think this Torque wrench is easy to use even for beginners.
How did it compare to other products?
Compared to the Large Torque wrench for Wheeletc. that I have, it is naturally lighter and easier to use.
But, as I wrote above, only the place where there is no Release of Socket was disappointing. (Because the one for Wheel has Release)
【Review】
This Torque wrench is moderately large and easy to use.
If I wanted, I could set up to 30N-m and if there was a release mechanism of Socket, it would have been a perfect score.
View detail
Cospar good
The content of the instruction manual of the attachment was difficult to understand, but I was able to understand it by the explanation written in the box. I think that the cost is good. View detail
It might be too large for me.
I always ignore Torque when I install Parts and I was worried about it.
But for a cheap price, Case is solid.
I thought that the time to use it would come sooner or later.
View detail
Easy-to-read voltmeter
The display screen is large and easy to read. I purchased this product because I thought that if there is an electrical failure, the first thing I would check is the battery. I think it is a good product because I can always check the strength of the battery and it is very clear at a glance. View detail
The handle is short!
[How is it used?
Maintenance of SEROW250fi
Was the one you received as per Image?
Yes
How was your experience with it?
Subject of comparison = Fujiwara Sangyo (EValue?) 3/8, Pre-set type, 20 to 110Nm
?The number of GEAR is 45T, so it is very good to be able to cachica fine!
?The pattern is short and Lever's principle is weak and Large strange.SEROW Tire on and off (85Nm) I did it by standing up and putting my weight on it. The Fujiwara Sangyo was able to do it by squatting and using only the strength of my arms???. I think it needs to be 5 cm longer than the Fujiwara Sangyo's so that the workability can keep up with the measuring ability.
? If you have a small torque of about 50Nm or less, coupled with the GEAR number, it's easy to use.
This is just an impression in my case, because there are individual differences in arm strength etc.
[Points to note]
? Above, where the handle is short. If you have a strong arm, it may be Large strong.
Memory is not in increments of 10, but in increments of 14. You'll get used to it.
How did it compare to other products?
As mentioned above, the number of GEARs is good, but the disadvantage is that the handle is short and difficult to apply force.
I've only used this and Fujiwara Sangyo, so I can't compare it to others.
View detail
It'll take some getting used to.
I was troubled between this product of Fujiwara Sangyo and STR3-60 of the pre-set type because the torque wrench which I am using now became old, but I decided to buy this product for the first time. I bought this product of Digital type for the first time.
It took a little time to get used to it at first because it is judged by the sound, the flashing of the LED, and the numerical value visually.
It's good to work in a position where you can see the LCD display, though, because at least you can see the values.
When I can't see the LCD display because I use it upside down, I have to rely on the sound.
Because the battery is consumed even if the power is turned off, it is troublesome to take out and install the battery, but it is said from the frequency of use, and is no problem?
The screw of the battery lid is not to come off from the lid, and the consideration not to lose it is good.
View detail
Small, but useful.
I bought this because of the low price to check the voltage status of Battery.
The installation was able to be done without so much problem, but it was difficult in the installation place of the display part though the thing was small, because it was attached to various things at the time of touring, I tried to stick it to the HandlebarStem part after all.
It is difficult to see while riding due to the poor installation location, but the display is small, but the letters are large and easy to read.
Sometimes it's hard to see depending on the sunlight.
It's a good product, though I'm temporarily removing it now.
View detail
Bagged for easy storage
I purchased this product because I needed to take various measurements for maintenance.
The deciding factor in the purchase
I chose this product because it is inexpensive and can measure up to 100mm.
It is good for universal use because it can measure outer diameter, inner diameter and depth.
[Impressions of using it]
I don't have anything to calibrate so I don't know the degree of accuracy, but I think it's sufficient for my needs.
I used it to measure a few products and it was a solid CommaZero so I felt it was solid.
Also, it's not Level which is a problem, but it's a bit reluctant to move. I think it would be better to oil it.
I love that it comes with a bag so there is less risk of loss, damage or injury. (It's kind of lame, but lol)
Products compared
We compared it to the Digital Caliper of the same Brand and the Caliper of the Others Tool Manufacturer.
I bought it because it was relatively inexpensive and I thought that the accuracy aspect would be safe because it was a brand that I saw in Home center etc.
Also, it's not uncommon for the Digital Caliper to run out of batteries when you need to use it, so...
【Review】
It is inexpensive, easy to use, and I found it to be very accurate.
I bought a Plastic Caliper at a 100-yen store and used it once, but it was damaged immediately, so it must be made of Gold.
View detail
Purchase Repeat
Previously purchased for XTZ
Reason for purchase
1. XTZ's Meter doesn't have a clock function.
2. I installed a Grip heater and want to check the voltage.
3. I can check the outside temperature.
This time, I bought it for GPX.
Reason for purchase
1. The GPX Meter has a clock function, but the Gaple
2. Same as XTZ 2.
3. Same as the XTZ 3.
I've been using it for about a year on my XTZ with no problems and it's very convenient.
View detail
Wide measurement range
[How is it used?
I already have a torque wrench, but it doesn't measure low torques, so I decided to buy this product which can measure low torques.
I bought it
Was the one you received as per Image?
Image
How was your experience with it?
When it gets close to the set torque, the green lamp turns on, a pippi sound is heard, and when it gets to the set torque, the red lamp turns on.
The sound changes to a continuous beeping sound.
Even if you don't set the Torque, the value will increase as you apply Torque, so you can set the desired Torque by looking at the value.
It's Compact so it will be useful around Handlebar and Spark plug replacement.
The lid of the battery is stopped by the screw, but there is no worry about losing it because it is held in the lid side even if the screw is removed.
There is no cuckooing when you get to the setpoint.
[Points to note]
I think it varies from person to person, but I felt the sound was Large.
Even if you turn off the power, the battery is still drained, so it is troublesome to have to take out the battery after use.
Because the length is short, it may be Large strange to work near the upper limit of the measurement range.
How did it compare to other products?
The famous brand products are expensive and I was worried about the durability and accuracy of the no-name products.
It's made inTaiwan, so I think it's solid.
Here is a LINK to the Handling Instruction Manual:http://180.42.73.61/volume/00017/imag/file35273/t010003527233.pdf
Other items that would be helpful
Installation points and hang/Items to buy together/ Opinions and requests to the Manufacturer
View detail
It is easy to use even for beginners.
This Inspection Tester is very useful to find out the permanent power supply or attachment power supply from the wiring cord of the vehicle. It is useful for USB and DriveRecorder installation. View detail
Tire air gauge
Compact and easy to carry.
Best of all, I found the air pressure to be nearly as accurate as the more expensive for RaceGauge.
That's the most Large cut there is. I am satisfied with it.
View detail
For Float pin removal etc.
The straightness of the pin is good and I use it to remove the Float pin when I overhaul the Carburetor. If the angle between the pin and the hammer is not good, the pin part may be bent by the force, but it is not broken and can be used by correcting the bend. The diameter of 1.5 or 2mm is very useful for Motorcycle. View detail