Reviews
Heat Seat
[How is it used?
When I replaced the Exhaust System of CRF125F, the Exhaust System was hitting the Cowl and the Cowl was melting due to the heat.
The back side is adhesive, just like an ordinary heat seat.
The product is neither good nor bad.
It is of a moderate large size, so it can be used in various situations.
View detail
Thermal measures!
I installed an Oil Temperature Meter on my NC750X, but I have to pass the WiringCable under the Engine, so I will try this heat resistant tape as a thermal countermeasure. I think it will be no problem. I am also planning to put the heat resistant tape on the Under Cowl of the NC750X because the heat from the exhaust system melts the Under Cowl. View detail
It takes a while to arrive, so you need to order early.
I don't want to get the inner thighs hot, so I referred to First's impresario.
It is easy to apply and the price is reasonable!
However, it takes a week or two to arrive, so if you need it right away, you need to order it as soon as possible.
View detail
Installation and processing was easy.
[How is it used?
Used for Under Cowl for CB1000R.
Two sheets of this product were used.
Was the one you received as per Image?
As per Image.
Was the installation difficult?
Simply align them by looking at the reference photos and remove the excess on the edges with Cutter.
We first aligned and determined the cutting position before processing.
Since the adhesive strength is strong, we applied it gradually from the edges.
It was easy to process (cutter & scissors) and soft enough to be affixed without gaps.
How was your experience with it?
It is non-stick and safe to ride on.
[Included Parts:were they on?
None
[Was there anything that disappointed you?
Cost performance is,...
View detail
For Cowl protection near Exhaust System
When I replaced it with an external exhaust system, it was melting when it hit the cowl, so I put it on to protect it.
Quantity:I double layered it because 1 pc. would melt.
I hope this doesn't melt.
It would be better if it were a little thicker.
It comes with a small MINISticker.
View detail
Excellent heat resistance
The stainless steel wire is included and can be wrapped tightly around the exhaust pipe. The stainless steel wire is included and can be wrapped tightly to prevent the motorcycle cover from melting. View detail
It's going to stick.
This product can be cut to any size and can be attached to any place of your choice with firm adhesive force, and is heat resistant to prevent deformation and discoloration of the Under Cowl due to the heat of the exhaust pipe. View detail
Fuel tank insulation
When I changed my fuel tank to aluminum before, I bought this kind of insulated seat. I bought it for Repair because it was worn out. I bought this one because the Manufacturer's one I bought before was out of stock. I've been using it for a long time and I've never had a problem with it. View detail
Mostly satisfied!
[How is it used?
I used it for Under Cowl of YZF-R25 which I use as Racer.
Was the one you received as per Image?
It was just like the Image. The thickness is there and it looks promising.
How was your experience with it?
The adhesive strength is strong there, but if you want to put it on the inside of Under Cowl, be careful because it will come off if you don't degrease it well.
In addition, it is not a problem if the shell of the Silencer hits, but if the exhaust pipe hits directly, it will be burnt. (laughs)
How did it compare to other products?
It's simple and easy, but the ones from Magical and others are thicker and more durable with things like Glass Wool mixed in.
View detail
It's thicker than I expected.
I used it as an insulator for Race cowl.
It was thicker than I expected and it interfered with the exhaust pipe.
However, the material does not stick to the exhaust pipe due to heat, etc., so the insulation is more than adequate.
View detail
I think it's good
I put a large piece of Heat Insulating Material on it and stuck this product around it.
I took this approach because it's relatively easy to cut.
I didn't use it for Motorcycle, but I repaired the Plate part of the GasCooker that had a hole in it from the heat.
It's been about a month now and there is no damage to the tape itself.
It was surprisingly useful, so it's a big deal. (Lol)
But for a few days, I think it was the glue, but the smell was too strong.
View detail
Measures against gasoline seepage
I installed it on the ZrX1200R where the back of the Fuel Tank is not heat resistant
This is a countermeasure against gasoline seepage from the tank cap
Previously, the Cork Board and Material:I was wearing my own piece of Aluminum Tempura Guard, but my own piece was falling apart Size is also good and easy to install
View detail
To prevent melting of Bike Cover.
I use it for Exhaust pipe.
Wrap both ends with needle Gold
Fixed with Hose Band.
Although it may not look good
The insulation effect was sufficient.
It was hardly hot..
View detail
Tank It is the width of the product that is easy to stick to the back
I bought it by measures against heat shielding to Fuel Tank going up from Engine.
This product has never looked at the shop which sells it in store inventory.
Since the use destination was Fuel Tank, the pasting surface was full of curved surfaces, so it is very easy to paste this product which has been cut to 5 cm width beforehand.
Because the adhesive tape is also solid, I think that once you paste it will not peel so easily.
Because of that, the Tape gets in the way when cutting the product with Scissors, and the adhesive Tape kasu adheres pretty much to the blade of the Scissors, so let's wipe frequently.
If not doing so, the adhesive Tape kuss calls further kasu, which results in a way to tear off the thermal barrier fiber and call for fraying of the fiber unnecessarily.
Anyway, the 5 centimeter width standard was easy to stick, workability was also very good
View detail
To insulation from Engine - - -
Purchased for insulation from Engine to Fuel Tank.
I cut it into strips and stuck it on the back of Tank.
The back is easily affixed with Double-sided Tape.
I thought that GlassWool that I cut is overflowing Cover so I stretched it with Aluminum Tape and pressed it down.
View detail
Used for insulation of Fuel Tank
Temperature also rises to protect Gasoline from the heat of Engine
Heat insulated using this product on the back of Fuel Tank.
It is wrapped in a roll and easy to cut to your favorite Size
There is no problem with adhesive strength.
In bad products it may be scratchy with Glass fiber,
This product is excellent in workability without Glass fiber Rose.
View detail
Scooter's Helmet inSpace's thermal barrier
I used it for heat shield of Helmet inSpace of Addressv125.
Remove Helmet in, paste from the outside.
The product came in one winding state.
I cut it to an appropriate length and pasted it.
I thought that Aluminum Tape says that it would be hard to stick to a place where it was bent..
When I started pasting, I felt that workability was very good because it was stuck to the curved surface unexpectedly and flexibly.
I thought that it could be used in various places depending on how it was used.
The price was affordable, so I thought that COSPA is a good product.
View detail
It purchased to use it for the interference portions of the Silencer of a Muffler, and a Undercowl.Since the product of other company seemed to be large and seemed to be user-unfriendly, I think that this article of a moderate size is good for an indi
It purchased to use it for the interference portions of the Silencer of a Muffler, and a Undercowl.Since the product of
other company seemed to be large and seemed to be user-unfriendly, I think that this article of a moderate size is good for an individual user.While using it about
engine performance, he would like to discern, but since there are not necessarily so various kinds, even if somewhat powerless, I think that the width of selection is narrow.
View detail
It sticks on the flesh side of the Tank of CB400SF, and made engine heat not get across to the body.Even all fragments fine in area were used, and most Tank flesh sides have been covered.The heat insulation effect was found clearly.Although it is sti
It sticks on the flesh side of the Tank of CB400SF, and made engine heat not get across to the body.Even all fragments fine in
area were used, and most Tank flesh sides have been covered.The heat insulation effect was found clearly.Although it is still hot in summer, is it better until now?Although it is likely to become impossible to feel warmth in the winter of
, it is satisfied with the heat insulation effect.
View detail
Although he plans to stick on a Cowl and being purchased, it did not become shielded state but the purchase of double-stick tape was required separately.Since wire was attached, originally I think the thing used winding around a Chamber.
Although he plans to stick on a Cowl and being purchased, it did not become shielded state but the purchase of double-stick tape was required separately.Since wire was attached, originally I think the thing used winding around a Chamber. View detail