Reviews
Convenient to have
We purchased this inexpensive product to replace our Exhaust pipe.
What used to be a painstaking process with Pliers and Pliers is now done in seconds. I wish I had bought it earlier. I wish I had bought it earlier, I chose the least expensive product and I have no complaints about the quality!
View detail
Exhaust Spring removal!
[How is it used?
When changing oil, the drain bolt cannot be removed without removing the exhaust pipe of the exhaust system.
Was the one you received as per Image?
Yes
How was your experience with it?
It was very convenient. It was so good that I felt like a fool for having worked so hard with Radio pliers.
It is only a few hundred yen, so it is worth having if you often remove Spring.
It is useful both when putting it on and taking it off.
[Points to note]
None
How did it compare to other products?
Anyway, it's cheap!
View detail
Good enough for the price.
I chose this product because of the price, but I am fully satisfied.
The consolidated Spring of Exhaust System is sufficient for this purpose.
View detail
Enough for Sunday mechanic
[How is it used?
STAND and Exhaust System during vehicle maintenance (Chamber) It is used to remove and install Spring for replacement etc.
Before purchasing this product, I had been working hard with a radipen, but I purchased this product to increase work efficiency.
Was the one you received as per Image?
It was just like the picture.
How was your experience with it?
The hook is processed so that the tip of the hook is tapered, allowing for smooth attachment and removal of the spring.
Also, the T-section is well reinforced, and although it is inexpensive, it does not seem to break easily.
The size is neither too small nor too large, but just right.
[Points to note]
None in particular. Surprisingly comes into play when it comes to maintenance.
How did it compare to other products?
This product has no problem, but some of the ones I used in the past had no reinforcement at the T-junction and would break off.
This is a part where force is inevitably applied, so I think this product is good because that part is reinforced.
【Review】
It is fairly inexpensive, but I think it works well for starters.
As expected, the durability will be inferior to those of famous manufacturers when used over a long period of time, but I think it will be sufficient for Sunday mechanicLevel.
View detail
Convenient to have
[How is it used?
YAMAHA XJR400R (07) Exhaust System replacement, etc.
The Exhaust System is removed when the Exhaust System is replaced at the time of vehicle inspection or when the Oil Filter is replaced.
In doing so, I have been using Pliers and others to pull Spring, but it is quite difficult to do.
I knew there was an exclusive product, but I had not been able to purchase it.
Was the one you received as per Image?
The image was exactly as shown in the image.
I was reluctant to use it because it has only one application, but since it is compact, it is easy to place.
How was your experience with it?
It is quite easy to use.
Installation and removal of Spring is now much easier.
I wish I had bought it sooner. w
[Points to note]
Nothing special, but be careful not to work on Spring so that it doesn't blow up!
How did it compare to other products?
I don't know because I have not used other products, but considering the price, I feel this product is fine.
It has the best cost performance.
View detail
It's so easy!
Purchased to remove Spring for replacement because the Screw threads on STAND's Nut were crushed and spinning.
I tried to replace it with a S-shaped Hook, but I was able to remove it, but I couldn't put it back on and the Spring flew off like a bullet.
It requires a certain amount of force, but I wish I had bought it in the first place if it was so easy to detach and reattach.
View detail
For safe operation
Purchased for my own Exhaust System replacement.
When installing the Exhaust Spring, it requires a lot of force and the body position is low, so it is a good idea to have it in order to prevent the Exhaust System from getting damaged and to prevent injury to the driver.
This product is 150mm long (measured after purchase) I can't say for sure because the force depends on the type of Exhaust Spring, but I was able to use it without any problems.
It is also a simple product and not used very often, but it is reasonably priced.
View detail
Easy to use
This Spring hook is durable and easy to use.
It is a must-have item for removing and installing the Full Exhaust System, and is easy to hold and non-slip, so there is no need to worry about getting wounds on the exhaust pipe.
View detail
Cheap and convenient.
This spring hook is very useful and inexpensive, and it is a must-have for the removal of the Full Exhaust System, so you don't have to worry about the wound sticking to the exhaust pipe, and you don't have to worry about injuring yourself by pulling with pliers. The Grip is easy to handle and is very easy to pull. View detail
Easy to use
I used it to replace the exhaust system of the Slip-on Silencer
I've often seen on the Net that Spring is hard to install, so I'm not sure how much it is I used this product to try it, and it was so easy to use Spring I was able to hook it up
The price is about 500 yen, so it's not a bad buy
View detail
Makes life easy
Makes removing/attaching springs a much easier process, quality is good for the price, and being a infrequently used product (but handy when used) it should last a very long time. Well worth it. View detail
Satisfied with more than just the costumer!
Bought it to do the Exhaust System replacement myself It was cheap and worked well enough
Until now, there have been many times Slip-on Silencer, but this time Full This is the first time to use the Exhaust System, so I thought it was necessary and bought it
It worked fine
View detail
It is good..
【What made you decide the purchase?】 Required
Cheap. I was using the Full Exhaust System when I was on the R6, but when I noticed, there was no Spring and I need to install it again.
【How was it actually used?】 Required
It's easy.. You can not go back to Pliers etc. using this.
[Is there anything I was disappointed about?] Required
There is none.
【Hope for Manufacturer - Please let me know if you have any improvement points]
I think that it is a hard Plastic part of a cheap hand. It's a soft material, but unfortunately it's becoming a negative feature over time.
【Have you compared items?】
Motorcycle store san used Manufacturer unknown thing, but I did not feel any particular difference.
[Others] Any
It is not this product but Spring's story, but it will naturally degrade when used for a long time. So, I use this product to remove or attach it, depending on things Spring breaks when pulling. Fine, there are times when I feel scary. I flew away the debris to the face.
When adding second-hand Exhaust System etc. Spring will renew. I think that it is more secure to prepare a reserve.
View detail
I could use it normally
Used for Spring fixed to the Flange section of External Chamber outside the company
It was quite hard Spring, but it worked without problem. I was worried because it is cheap, but I think it's tough..
View detail
After all it is a special tool!
Until now I used Pliers and my own tools, and I was often injured
After all it is special tool, easy to use and safe
From now on, I am worried about the exchange of Brake spring, Side Stand Spring, no longer suffer
View detail
It was convenient.
I used Pliers etc until now, but dedicated Spring hook is messed up.
Inner baffle that could not be pulled out could be removed with this and it was two stone with one stone (Lol)
View detail
Necessities
Exhaust System, STAND etc. Hooking Spring is a lot.
I used to hook Driver or pull it up with Pliers, but I've been scratching it with prying etc. It is convenient.
If it is an Exhaust Spring, there is no problem because there is enough direction to pull on the Exhaust Spring, but Spring of STAND can easily install Spring when you apply weight through the Double-end Wrench of Large eyes.
It is a simple tool but there is not a difference between Large.
If you have parts to remove, one should have one.
View detail
It is a good product.
I bought it because the price was cheap and it seemed easy to use. It was actually easy to use. I was very happy because it was too early to order from ordering to hand. View detail
You can use!
I thought that it would not be a problem if nothing but I bought it. In our CUB with Engine desorption, under waist Overhaul (Kick starter spindle return spring wearing - Large active at the time of desorption). If you do not need it, you can shorten the working time to the Large width.
There is no problem in the use feeling at all.
View detail