Reviews
Heart breaker!
First and foremost, we must note that the BALI in the cutting process is quite bad, and honestly, it is the Level that causes injury.
If it is a FOR JAPAN MODEL product, I think it is a hesitant Level to ship the product as it is.
And it is not very good as accuracy, and the Center axis is also blurred.
However, it does not mean that it cannot be used at all. If BALI is removed sesse-sese-sese and military gloves are used, it is not impossible to use it.
However, we do not anticipate that the product will be used many times, and we hope that you will consider it as a disposable level for this time.
Personally, I would urge everyone to choose a more solid product when considering it as a tool.
well ♪ Hyakkety-yak ♪ It is possible for people who understand the concept of "Level" to purchase the product.
View detail
As you tighten it in.
I use it for Caliper's rubout etc. When I tighten the Screw and open the Plate with 4POTCaliper like NC30, the Plate is not parallel and I can't get the 4 Pistons to be even etc.
The fact that it cannot be pushed in makes it difficult to use. The texture is good, so I would like to have the Guide of Plate as Quantity instead of 1 pc.:I am wondering if I should have purchased the 2pc one.
View detail
Fits: Others , HONDA GROM, HONDA MSX125, HONDA MONKEY125, HONDA SUPER CUB110, HONDA CROSSCUB110
I don't want it in jc92Clutch.
I don't use it to replace the Clutch on my jc92.
Clutch lock nut is 19mm.
View detail
Somewhat difficult to use
I'm glad it's reasonably priced, but it seems a little difficult to use…
It is not a consumable item, and I wish it were more expensive and easier to use.
The instructions on the back of the Package were easy to understand.
View detail
OHLINS Preload AdjusterTool
As for the dryness of use, it is only an OEMTool, and the accuracy of the Size is good and easy to use.
But the Gold amount is still too high.
View detail
The stuff is good, but I didn't need it!
Purchased to remove Locker Arm on xs250sp 4a8.
I bought it without checking because it was mentioned in the tool section of the service manual and was also used in the photo of the procedure for removing the Locker Arm.
As a result, the Bolt of Locker Arm was M8 and the size was not M6.
If you check the photos of the procedure carefully, it is just a Bolt. The color is different!
I bought a M8×180mm Bolt for 300 yen at a nearby Home center and was able to remove it successfully.
Things are good. I just didn't need it.
View detail
Monozukuri Japan is a thing of the past
This is a replacement for a Brush (Manufacturer unknown) that I bought about 10 years ago.
good point
I think the costumers are good.
A bad point
・ Brush width can be adjusted according to Chain/Size. but when adjusting to a thin Chain, Brush cannot be fixed.
You will have to go to the trouble of using old newspapers or Vinyl gloves to grab the Grease-soaked Brush.
Two rows of adjustment grooves should be added.
I bought Brush about 10 years ago." and the structure is the same, no growth. Mr. DAYTONA, the venerable DAYTONA!!!
...in a TV commercial for Tooth Brush. Head is thin." If this Brush Head is also made thinner, it should be possible to reduce the overall width by about 5mm.
It improves workability by preventing interference with Nut around Chain case and Sprocket.
Others
I would like the employees of a company that handles Motorcycle products to be Motorcycle enthusiasts, to have a thorough knowledge of the actual products they handle, and to plan and develop them with passion.
View detail
Hard to polish the details...
I purchased this product for the purpose of shortening ChainMaintenance time.
It is efficient because it can clean three surfaces at the same time, but the bristles of the Brush are thick and hard, so it is difficult to polish fine details.
So I do a rough overall cleaning with a 3-sided Brush, and then polish the fine details with a pig-bristle Brush or regular tooth Brush.
In the end, I don't think it's much of a time saver...
View detail
Note the length of Drill.
If the Drill length is too short, the hole cannot be drilled. View detail
It's just one of those things.
It's not impossible to use, but it was easy to come off because the hook was too weak.
I think it would have been easier to use if there were no bumps in the patches.
View detail
I don't think it fits...
I couldn't figure out why it was exclusive to 2Valve, so I bought it to try it out.
As a result, the duplex Spring could not be pushed off by hand and could not be used.
For use with Mini bikes.
View detail
You can't have hard ends.
I could not Cut the hard end of the PillowGrip on the Pro taper.
I stopped because the iron part of Cutter was deformed while I was beating it.
I bought it for this...
Since the Material is iron, I thought I could make the cutter part a little sharper.
The kratom crackers in the picture cut it with no problem.
I don't know if it's because I don't care too much about the finish, but as others have said, the holes are definitely a little gapped.
If you don't mind, it might not be a problem.
It's not a tool I use often, and the price seemed a bit high, so I didn't change it for a long time.
If it was about $1,500, I would have bought it sooner.
I thought it would be nice to have a plastic Case to store everything in!
View detail
Fits: HONDA Shirley 70, HONDA Shirley 50., HONDA Shirley 70, HONDA Shirley 50.
Skewed!
The mounting bracket is totally skewed.. Had contact with seller but did not solve the problem. Only siad it could be mounted even with a skewed bracket, but that's NOT what I want in my Chaly! Can't upload photo unfortunately.. View detail
Difficult to use
The accuracy of the metal saw's guide is not quite right, and it gets stuck in the middle of the process, which can be a bit annoying. It is. View detail
After the worst
If there's a problem with the LCD or operation, it can be repaired, but then I'll buy another one, and that's repair pricing
I'm not bad at wearing the solder on the base, but I'm not good at it
I can't imagine buying another one
View detail
Fits: HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA GORILLA, HONDA GORILLA, HONDA GORILLA, HONDA MONKEY, HONDA GORILLA
Unsuitable for adherent flaho
I used it to remove the flywheel from my 30 year old Motorcycle and it was easy to use It's not good
One thing that is not so good is that the Handlebar, which is the part to put the force, is screw shaped and It is the point that it is not possible to work with force, such as biting the Pipe
You might be able to use it for a non-adherent flaho, but remove the flaho when it's not sticking in the first place I don't think there are many opportunities for this
By the way, the Furaho that couldn't be removed by this product came off easily with the OEM tool
View detail
I was sent a shoddy product
I ordered a specified part number that fit the top cap, but received a poorly processed item that did not fit the size at all
The top cap was scratched at the tentative fitting stage, and was replaced by the official Japan distributor We have submitted an Objection directly to EngineerRing
The top cap was scratched by a badly machined tool, so we asked them to process the tool to make the top cap more durable The cap was also replaced with a new one
Mr. MatsumotoEngineerRing's objection support was very reliable, but the I think it's best to inspect the product itself by yourself because it may be a bit of a stretch It is
Since it is a Made in Italy product, you should be more careful than Japanese products When something happens, it takes a long time to deliver
We recommend that you contact your authorized distributor immediately if there are any deficiencies
View detail
How is that?
When using 1 or 2 times Screw - - - Fixed with Tap and Dice after use (sweat) Screw run out after 3 rd use, it was not possible to use (Tears) After examining various things, Mr. Takekawa's Chain Tool was not well received! It was exactly right (Lol) View detail
Pump and Hose need more time!
The essential Pump and Oil Resistant Hose are removed during work. Since it does not become a thing if it is as it is, I fixed the joint with liquid packing. Pump is made by medical NIPRO, but it is not compatible with Oil Resistant Hose.
Well ~ Motorcycle related Parts are generally useless unless you add your own hands!
View detail
It can break immediately with the first time
There was a set of Body and a substitute Pick.
First turn turn Screw before Chain cut and you see that Pick is bent.
Since I can not use it, I tried doing it with Cut, but it caught on pulling out and broke.
When I exchanged for a replacement Pick and turned Screw, it was not bent more than the first one.
Chain cut and tried to pull out again.
It is durable due to poor precision.
If so high things are better.
View detail